NTB21-080
Service Bulletin Details
Public Details for: NTB21-080
Models from 2021
2021 NISSAN FRONTIER |
Models from 2020
2020 NISSAN FRONTIER |
Classification: Reference: EC21-018 Date: NTB21-080 September 1, 2021 MIL ON WITH DTC P0223, P0507 AND/OR P2135 STORED IN THE ECM APPLIED VEHICLES: 2020-2021 Frontier (D40) IF YOU CONFIRM The MIL is ON and one or more of the following DTCs is stored in the ECM: P0223 - TP SEN 1/CIRC-B1 P0507 - ISC SYSTEM P2135 - TP SENSOR-B1 AND There are no drivability concerns. ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/3 SERVICE PROCEDURE Using C-III plus, confirm the current ECM part number and write it on the repair order. 1. If it matches one of the part numbers in Table 1, continue to step 2 on page 3. If it does not match one of the part numbers in Table 1, this bulletin does not apply. Go back to ASIST for further diagnostic and repair information. Table 1 MODEL Frontier YEAR CURRENT ECM PART NUMBER: 23710- 2020 9BT6A, 9BT7A 2021 9BT8A, 9BT9A Perform the following before starting the reprogramming procedure to prevent damage to the control unit. Connect the AC Adapter to the CONSULT PC. Connect the CONSULT PC to the Internet via Wi-Fi or a network cable. Ensure ASIST on the CONSULT PC has been synchronized (updated) to the current date and all C-III plus software updates (if any) have been installed. Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI. If Bluetooth® signal waves are within range of the CONSULT PC or VI during reprogramming, the reprogramming may be interrupted. Turn OFF all vehicle electrical loads. Turn ON the hazard warning lamps. Connect a battery maintainer or smart charger, set to reflash mode or a similar setting, to ensure the battery voltage stays between 12.0 V and 15.5 V. HINT: If you are not familiar with the reprogramming procedure, click here. This will link you to the "CONSULT-III plus (C-III plus) ECM Reprogramming" general procedure. Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learning conditions: Engine coolant temperature: 70 - 100°C (158 - 212°F) Battery voltage: More than 12.9 V (At idle) Transmission: Warmed up When reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learning, Accelerator Closed Position and DTC Erase. 2/3 NTB21-080 2. Reprogram the ECM. 3. After completing Erase ALL DTCs, print a copy of the C-III plus screen showing the before and after part numbers of the control unit and attach it to the repair order. CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Reprogram the ECM (1) DE97AA ZE 32 (2) (1) Reference the electronic parts catalog and use the ECM part number (23703-*****) as the Primary Failed Part (PFP). (2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat Rate Time (FRT). AMENDMENT HISTORY PUBLISHED DATE REFERENCE September 1, 2021 NTB21-080 DESCRIPTION Original bulletin published 3/3 NTB21-080