NTB21-092

Classification:
Reference:
EC21-014
Date:
NTB21-092
September 30, 2021
MIL ON WITH DTC P0404 STORED IN THE ECM
APPLIED VEHICLES:
APPLIED ENGINE:
2021 Rogue (T33)
PR25DD
IF YOU CONFIRM
The MIL is ON and DTC P0404 (EGR VOLUME CONTROL VALVE) is stored in the ECM,
AND
There are no drivability concerns.
ACTION
1.
Confirm the current ECM part number.
2.
Reprogram the ECM, if applicable.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/3
SERVICE PROCEDURE
Using C-III plus, confirm the current ECM part number and write it on the repair order.
1.

If it matches one of the part numbers in Table 1, continue to step 2 on page 3.

If it does not match one of the part numbers in Table 1, this bulletin does not apply.
Go back to ASIST for further diagnostic and repair information.
Table 1
MODEL
Rogue
YEAR
CURRENT ECM PART NUMBER: 23761-
2021
6RA2E
6RA6B, 6RA7C
6RA8C, 6RA9C
6RR0E, 6RR1C
6RR3E, 6RR4C
6RR6B, 6RR6C
6RR7A, 6RR7B, 6RR7C, 6RR7D
6RR8A, 6RR8B, 6RR8C
6RR9B, 6RR9C
6RW0B, 6RW0C, 6RW0E
6RW1B, 6RW1C, 6RW1E
6RW2B, 6RW2C, 6RW2E
6RW3B, 6RW3C, 6RW3E
Perform the following before starting the reprogramming procedure to prevent damage to the
control unit.







Connect the AC Adapter to the CONSULT PC.
Connect the CONSULT PC to the Internet via Wi-Fi or a network cable.
Ensure ASIST on the CONSULT PC has been synchronized (updated) to the current
date and all C-III plus software updates (if any) have been installed.
Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range
of the CONSULT PC and the VI. If Bluetooth® signal waves are within range of the
CONSULT PC or VI during reprogramming, the reprogramming may be interrupted.
Turn OFF all vehicle electrical loads.
Turn ON the hazard warning lamps.
Connect a battery maintainer or smart charger, set to reflash mode or a similar setting,
to ensure the battery voltage stays between 12.0 V and 15.5 V.
2/3
NTB21-092
HINT:
 If you are not familiar with the reprogramming procedure, click here. This will link you
to the "CONSULT-III plus (C-III plus) ECM Reprogramming" general procedure.
 Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume
Learning conditions:
 Engine coolant temperature: 70 - 100°C (158 - 212°F)
 Battery voltage: More than 12.9 V (At idle)
 Transmission: Warmed up
 When reprogramming is complete, you will be required to perform Throttle Valve
Closed Position, Idle Air Volume Learning, Accelerator Closed Position and DTC
Erase.
2.
Reprogram the ECM.
3.
After completing Erase ALL DTCs, print a copy of the C-III plus screen showing the
before and after part numbers of the control unit and attach it to the repair order.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Reprogram the ECM
(1)
DE97AA
ZE
32
(2)
(1) Reference the electronic parts catalog and use the ECM part number (23703-*****) as
the Primary Failed Part (PFP).
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time (FRT).
AMENDMENT HISTORY
PUBLISHED DATE
REFERENCE
September 30, 2021
NTB21-092
DESCRIPTION
Original bulletin published
3/3
NTB21-092