No. 182-21
Service Bulletin Details
Public Details for: No. 182-21
Information on reverse camera - misted up and/or droplets forming in camera lens. Rework rea lid release.
- 2021 - 2020 - 2019 - 2018 - 2017 -
Models from 2021
2021 PORSCHE PANAMERA |
Models from 2020
2020 PORSCHE PANAMERA |
Models from 2019
2019 PORSCHE PANAMERA |
Models from 2018
2018 PORSCHE PANAMERA |
Models from 2017
2017 PORSCHE PANAMERA |
Service Technical Information 182/21 ENU 9143 9 Reversing Camera Misted Up and/or Droplets Forming in the Camera Lens: Rework Rear Lid Release (182/21) Model Line: Panamera (971) Model Year: As of 2017 up to 2021 Equipment: • • Concerns: Reversing camera Information: The customer complains that the image on the reversing camera view on the PCM screen is cloudy. Drops and/or fogging are visible behind the reversing camera lens. Ultrasonic parking assistant and reversing camera (M-no. 7X8) Ultrasonic parking assistant with Real Top View (M-no. 8A4) This may be caused by joint tolerances of the components in the reversing camera area as well as tolerances in the thickness of the body seam seal. They can cause the release for the rear lid in which the reversing camera is installed to touch the rear lid. If this happens, there is a gap between the release and the rear lid that can allow water to penetrate into the reversing camera. Formation of drops Contact between PVC seam and rear lid release AfterSales Dec 10, 2021 Page 1 of 7 9 Service Technical Information ENU 182/21 9143 Gap between release and rear lid Action required: In the event of a complaint, rework rear lid release and replace reversing camera. Required tools, parts and materials Tool: • • Calliper gauge Fine-grained file Parts Info: Part No. Designation Number 9A798055600 Reversing camera 1 ea or 5Q0980546A Materials: • Camera (Real Top View) 1 ea Adhesive tape/insulating tape Preparatory work Work Procedure: 1 Dec 10, 2021 Page 2 of 7 Remove reversing camera. Workshop Manual '914319 Removing and installing reversing camera' AfterSales Service Technical Information 182/21 ENU 9143 9 Reworking rear lid release Work Procedure: Affix a max. 5 mm/ 0.20 in wide chamfer to the actuator for the rear lid to prevent contact between the rear lid release and rear lid and to ensure that the seal is secure. 1 Set calliper gauge to a width of 5 mm/ 0.20 in. Then scribe the surface to be removed as shown in Marking area to be removed using the calliper gauge. Contact points Marking area to be removed AfterSales Dec 10, 2021 Page 3 of 7 9 Service Technical Information ENU 182/21 9143 2 Mask the spray nozzle for the reversing camera at the actuator for the rear lid as shown in Masking spray nozzle using suitable adhesive or insulating tape. Masking spray nozzle Dec 10, 2021 Page 4 of 7 AfterSales Service Technical Information 3 182/21 ENU 9143 9 Remove the area you marked earlier using a fine-grained file over a width of max. 5 mm/ 0.20 in. Installing chamfer Information In most cases, it is sufficient to remove approx. 2-3 mm/ 0.08 — 0.12 in of material. Therefore, install the rear lid release in between and check the installation position after you have removed some material. Then, remove more material if necessary. Installing chamfer AfterSales Dec 10, 2021 Page 5 of 7 9 Service Technical Information ENU 182/21 9143 4 Remove previously applied adhesive tape or insulating tape from the spray nozzle for the reversing camera. Example of completed rework Dec 10, 2021 Page 6 of 7 AfterSales Service Technical Information 182/21 ENU 9143 9 Concluding work Work Procedure: 1 Install new reversing camera in the reworked release for the rear lid and install release for the rear lid together with the reversing camera. Then calibrate the reversing camera. For instructions, see: Workshop Manual '555719 Removing and installing rear lid release' Workshop Manual '914319 Removing and installing reversing camera' Invoicing Invoicing: For documentation and warranty invoicing, enter the working position and PCSS encryption specified below in the warranty claim: APOS Labor operation 91434900 Rework reversing camera I No. PCSS encryption: Location (FES5) 91430 Reversing camera Damage type (SA4) 5012 fogging, water condensation, humidity References: Workshop Manual '914319 Removing and installing reversing camera' Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed. © 2021 Porsche Cars North America, Inc. AfterSales Dec 10, 2021 Page 7 of 7