TSB_FUE058
Service Bulletin Details
Public Details for: TSB_FUE058
Technical service bulletin:1.6l t-gdi with mil on dtc P00B7 ecm logic improvement & a/c torque demand - this bulletin provides the procedure to update the software logic of the engine control module (ecm) system on some 2021-2022my k5 (dl3a
Models from 2022
2022 KIA K5 |
Models from 2021
2021 KIA K5 |
GROUP MODEL FUE 2021-2022MY K5 (DL3a) w/1.6L T-GDI NUMBER DATE 058 April 2022 TECHNICAL SERVICE BULLETIN 1.6L T-GDI WITH MIL ON DTC P00B7 ECM LOGIC IMPROVEMENT & A/C TORQUE DEMAND This bulletin provides the procedure to update the software logic of the Engine Control Module (ECM) system on some 2021-2022MY K5 (DL3a) vehicles equipped with the Gamma 1.6L T-GDI engine produced from March 27, 2020 through January 10, 2022, which may exhibit an MIL ON with DTC P00B7 and/or RPM fluctuation and possible stalling when turning A/C ‘OFF’ while vehicle is parked. Follow the procedure outlined in this publication to apply the improved logic to the ‘Engine’ system using the KDS ECU Upgrade function as described in this bulletin. For confirmation that the latest reflash has been applied to a vehicle you are working on, verify the ROM ID using the table on page 3 of this bulletin. DTC Description: P00B7 – Engine Coolant Flow Low/Performance Kia Diagnostic System (KDS) A printed copy is for reference only; publication information can be updated at any time. Always refer to KGIS for the latest information. After logging in kdealer.com, the newest technical publications are listed in ‘Service Releases’ and has the latest service information that has been released. Page 2 of 8 1.6L T-GDI WITH MIL ON DTC P00B7 ECM LOGIC IMPROVEMENT & A/C TORQUE DEMAND SUBJECT: ECU Upgrade Procedure: To correct this condition, the ECU should be reprogrammed using the KDS download, as described in this bulletin. Upgrade Event Name 607. DL3a GAMMA 1.6TGDI ENGINE MIL ON DTC (P00B7) JUDGMENT LOGIC IMPROVEMENT NOTICE • Confirm a fully charged battery (12.3 volts or higher is necessary) is used or utilize a fully charged jump starter box connected to the battery. • Ensure the KDS is sufficiently charged at 60% or higher prior to reflash. • All ECU upgrades must be performed with the ignition set to the ‘ON’ position unless otherwise stated. • Damaged VCI II units should not be used and promptly replaced. • Be careful not to disconnect the VCI-II connected to the vehicle during the ECU upgrade procedure. • DO NOT start the engine during ECU upgrade. • DO NOT turn the ignition key ‘OFF’ or interrupt the power supply during ECU upgrade. • When the ECU upgrade is completed, turn the ignition ‘OFF’ and wait 10 seconds before starting the engine. • ONLY use approved ECU upgrade software designated for the correct application. IMPORTANT It is recommended to ALWAYS check the Electronic Parts Catalog (EPC) to locate the ECU Part Number respective to Auto/Manual Mode ROM IDs. DO NOT reference the parts label affixed to the ECU. Before attempting an ECU upgrade on any Kia model, make sure to first determine whether the applicable model is equipped with an immobilizer security system. Failure to follow proper procedures may cause the PCM to become inoperative after the upgrade and any claims associated with this repair may be subject to chargeback. Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information. TSB: FUE058 K5 (DL3a) April 2022 Page 3 of 8 1.6L T-GDI WITH MIL ON DTC P00B7 ECM LOGIC IMPROVEMENT & A/C TORQUE DEMAND SUBJECT: ROM ID INFORMATION TABLE: Upgrade Event #607 Model EM TM IMMO ISG ECU P/No. Previous New 39121 2MKK0 TDLA1NU06F022E0K TDLA1NU06F122E0K TDLA1NU06F223E0K TDLA1NU06F424E0K TDLA1NU06F524E0K TDLA1NU06F52FE0K 39123 2MKK0 TDLA1NU06E022E0K TDLA1NU06E122E0K TDLA1NU06E223E0K TDLA1NU06E424E0K TDLA1NU06E524E0K TDLA1NU06E52FE0K 39121 2MKT0 TDLA1NU06F022E03 TDLA1NU06F122E03 TDLA1NU06F223E03 TDLA1NU06F424E03 TDLA1NU06F524E03 TDLA1NU06F52FE03 39123 2MKT0 TDLA1NU06E022E03 TDLA1NU06E122E03 TDLA1NU06E223E03 TDLA1NU06E424E03 TDLA1NU06E524E03 TDLA1NU06E52FE03 Yes 39121 2MKV0 TDLA1NU06F026K03 TDLA1NU06F126K03 TDLA1NU06F12FK03 No 39123 2MKV0 TDLA1NU06E026K03 TDLA1NU06E126K03 TDLA1NU06E12FK03 Yes 39121 2MKK1 TDLA2NU06F02EE0K TDLA2NU06F12FE0K TDLA2NU06F22FE0K No 39123 2MKK1 TDLA2NU06E02EE0K TDLA2NU06E12FE0K TDLA2NU06E22FE0K Yes 39121 2MKT1 TDLA2NU06F02EE03 TDLA2NU06F12FE03 TDLA2NU06F22FE03 No 39123 2MKT1 TDLA2NU06E02EE03 TDLA2NU06E12FE03 TDLA2NU06E22FE03 Yes 39121 2MKV1 TDLA2NU06F02EK03 TDLA2NU06F12FK03 TDLA2NU06F22FK03 No 39123 2MKV1 TDLA2NU06E02EK03 TDLA2NU06E12FK03 TDLA2NU06E22FK03 Yes Yes No 21MY DL3a Yes (1.6L T-GDI) ULEV 70 8AT No No Yes 22MY DL3a (1.6L T-GDI) ROM ID No To verify the vehicle is affected, be sure to check the Calibration Identification of the vehicle's ECM ROM ID and reference the Information Table as necessary. Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information. TSB: FUE058 K5 (DL3a) April 2022 Page 4 of 8 1.6L T-GDI WITH MIL ON DTC P00B7 ECM LOGIC IMPROVEMENT & A/C TORQUE DEMAND SUBJECT: NOTICE Prior to performing the ECU upgrade, be sure to check that the KDS is fully charged. 1. Connect the VCI-II to the OBD-II connector, located under the driver’s side of the instrument panel. NOTICE The ECU upgrade function on KDS operates wirelessly. It is not necessary to perform the upgrade via USB cable. 2. With the ignition ON, turn ON the KDS tablet. Select ‘KDS’ from the home screen. Confirm communication with VCI (A) and then configure the vehicle (B) using the ‘AUTO VIN’ (C) feature. B A C 4. Select ‘ECU Upgrade’. Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information. TSB: FUE058 K5 (DL3a) April 2022 Page 5 of 8 1.6L T-GDI WITH MIL ON DTC P00B7 ECM LOGIC IMPROVEMENT & A/C TORQUE DEMAND SUBJECT: 5. The KDS will check the server for recently uploaded Events and then automatically download Upgrade Event #607. NOTICE The vehicle must be identified in Vehicle Selection to download an Event for that vehicle. 6. KDS screenshot shown above is for demonstration purposes only. Events shown in screenshot are not applicable to this bulletin. Select Auto Mode. CAUTION Do NOT attempt to perform a Manual Mode upgrade UNLESS Auto Mode fails. Always follow the instructions given on the KDS in either Auto or Manual mode. Select the Engine system under the System selection menu. Touch ID Check (D) and confirm that the latest D update is available. Select Upgrade Event #607 and select Upgrade to continue. The ECU upgrade will begin and the progress of the upgrade will appear on the bar graph. E Upgrade part (1/2) (E) will download the upgrade event to the VCI-II. Upgrade part (2/2) (F) will upgrade the ECU. CAUTION F Do not touch the system buttons (like ‘Back’, ‘Home’, ‘etc.’) while performing ECU Upgrade. Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information. TSB: FUE058 K5 (DL3a) April 2022 Page 6 of 8 1.6L T-GDI WITH MIL ON DTC P00B7 ECM LOGIC IMPROVEMENT & A/C TORQUE DEMAND SUBJECT: 9. If a “Communication Fail” screen appears, verify that the VCI-II and KDS are communicating properly. Select ‘OK’ and restart the procedure from step 4. NOTICE If an error notice continues to appear or if the upgrade cannot be performed, DO NOT disconnect the KDS/VCI-II. Contact GIT America Help Desk at (888) 542-4371 or Techline. 10. When instructed on the KDS, turn the ignition OFF for ten (10) seconds then back on. Select ‘OK’ to continue. 11. Once the upgrade is complete, select ‘OK’ to finalize the procedure. 12. When prompted, select ‘YES’ to check for Diagnostic Trouble Codes (DTC) and erase any DTCs stored such as EPS, ESC, and TPMS that may have been set during the upgrade. 13. Start the engine to confirm normal operation of the vehicle. Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information. TSB: FUE058 K5 (DL3a) April 2022 Page 7 of 8 1.6L T-GDI WITH MIL ON DTC P00B7 ECM LOGIC IMPROVEMENT & A/C TORQUE DEMAND SUBJECT: Manual Upgrade Procedure: NOTICE The manual upgrade should ONLY be performed if the automatic upgrade fails. If the automatic upgrade fails, turn the ignition ‘OFF’ for about 10 seconds then place it back in the ‘ON’ position to reset the control unit BEFORE performing manual upgrade. See table below for ‘Manual Mode’ passwords. Manual Mode ECU Upgrade Passwords Menu Password DL3a Gamma 1.6TGDI ULEV 70 8AT +IMMO/SMK +ISG (21MY): 39121-2MKK0 0701 DL3a Gamma 1.6TGDI ULEV 70 8AT -IMMO +ISG (21MY): 39123-2MKK0 0702 DL3a Gamma 1.6TGDI ULEV 70 8AT +IMMO/SMK (21MY): 39121-2MKT0 0703 DL3a Gamma 1.6TGDI ULEV 70 8AT -IMMO (21MY): 39123-2MKT0 0704 DL3a Gamma 1.6TGDI ULEV 70 8AT +IMMO/SMK (21MY): 39121-2MKV0 0705 DL3a Gamma 1.6TGDI ULEV 70 8AT -IMMO (21MY): 39123-2MKV0 0706 DL3a Gamma 1.6TGDI ULEV 70 8AT +IMMO/SMK +ISG (22MY): 39121-2MKK1 0707 DL3a Gamma 1.6TGDI ULEV 70 8AT -IMMO +ISG (22MY): 39123-2MKK1 0708 DL3a Gamma 1.6TGDI ULEV 70 8AT +IMMO/SMK (22MY): 39121-2MKT1 0709 DL3a Gamma 1.6TGDI ULEV 70 8AT -IMMO (22MY): 39123-2MKT1 0710 DL3a Gamma 1.6TGDI ULEV 70 8AT +IMMO/SMK (22MY): 39121-2MKV1 0711 DL3a Gamma 1.6TGDI ULEV 70 8AT -IMMO (22MY): 39123-2MKV1 0712 1. Within the ECU Upgrade screen displayed, select Manual Mode. 2. Select the Engine system under the System selection menu. Select Upgrade Event #607 and select Upgrade to continue. 3. Select the appropriate control unit part number with reference to the ROM ID Information Table on page 3, and select OK. 4. Enter the appropriate password from the Manual Mode password table above and select OK. 5. The upgrade will begin and the progress of the upgrade will appear on the bar graph. 6. When instructed on the KDS, turn the ignition OFF for ten (10) seconds then back on. Select OK. 7. Once the upgrade is complete, select OK to finalize the procedure. 8. When prompted, select YES to check for Diagnostic Trouble Codes (DTC) and erase any DTCs stored such as EPS, ESC, and TPMS that may have been set during the upgrade. 9. Start the engine to confirm proper operation of the vehicle. Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information. TSB: FUE058 K5 (DL3a) April 2022 Page 8 of 8 1.6L T-GDI WITH MIL ON DTC P00B7 ECM LOGIC IMPROVEMENT & A/C TORQUE DEMAND SUBJECT: AFFECTED VEHICLE RANGE: Model Production Date Range K5 (DL3a) March 27, 2020 to January 10, 2022, REQUIRED TOOL: Tool Name Figure Comments KDS Kia Diagnostic System WARRANTY INFORMATION: N Code: I3A C Code: ZZ3 Claim Type W Causal P/N Qty. Repair Description 39101 2S002 0 ECM Logic Improvement Labor Op Op Replacement Code Time P/N 39121F02 0.4 M/H Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information. TSB: FUE058 K5 (DL3a) April 2022 N/A Qty. 0