A6922862051242_6
Service Bulletin Details
Public Details for: A6922862051242_6
This bulletin contains instructions for correcting dtc B1225f1.
Models from 2019
| 2019 AUDI A4 |
| 2019 AUDI A5 |
| 2019 AUDI A5 CABRIOLET |
| 2019 AUDI Q5 |
| 2019 AUDI Q7 |
| 2019 AUDI RS5 |
| 2019 AUDI S4 |
| 2019 AUDI S5 |
| 2019 AUDI S5 CABRIOLET |
| 2019 AUDI SQ5 |
Models from 2018
| 2018 AUDI A4 |
| 2018 AUDI A5 |
| 2018 AUDI A5 CABRIOLET |
| 2018 AUDI Q5 |
| 2018 AUDI Q7 |
| 2018 AUDI S4 |
| 2018 AUDI S5 |
| 2018 AUDI S5 CABRIOLET |
| 2018 AUDI SQ5 |
Models from 2017
| 2017 AUDI A4 |
| 2017 AUDI Q7 |
Technical Service Bulletin 69 Airbag warning light on, DTC B1225F1 stored in the airbag control module 69 22 86 2051242/6 May 4, 2022. Supersedes Technical Service Bulletin Group 69 number 19-41 dated July 24, 2019, for reasons listed below. Model(s) Year VIN Range Vehicle-Specific Equipment All Not Applicable A4 allroad, 2017 – 2019 A4, and Q7 S4, A5, A5 Cabriolet, A5 Sportback, S5, S5 2018 – 2019 Cabriolet, S5 Sportback, Q5, SQ5, and SQ7 RS 5, and RS5 Sportback 2019 Condition REVISION HISTORY Revision Date Purpose 6 - Revised Service (Added note for Campaign 74E3) 5 07/24/2019 Revised Condition (Removed Note) 4 06/26/2019 Revised header (Added Q5) Revised Service (Added Q5 procedure) Customer states: © 2021 Audi of America, Inc. Page 1 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin • Airbag warning lamp is illuminated in the driver information system (DIS). • Customer may also report that the passenger airbag indicator lamp in the overhead console may show that the airbag is off. Workshop findings: The following DTC is stored in the airbag control module, J234 (address word 0015): DTC B1225F1 (Seat occupied recognition sensor mat Shield wire, open circuit). Technical Background Not applicable. Production Solution There is a concern with the aluminum shielding on the PODS harness under the seat that is causing the DTC B1225F1 to occur. The aluminum sleeve isn’t fitted tight enough to the harness, a small amount of interference is possible and causes the fault. The service solution is to apply cable ties at two different points of the harness under the seat which tightens the fit of the aluminum shielding and corrects the issue. Service A4 and A5 1. Do not follow this TSB. Please perform Campaign 74E3 instead. Q7 1. To apply the cable ties, the seat does not need to be removed. You will need to move the lateral seat adjustment all the way to rearmost adjustment limit and the vertical height adjustment all the way to the upper adjustment limit. Once the seat is adjusted to the above-mentioned position, you will see the need to attach the cable ties at two points on the harness as shown (Figure 1). © 2021 Audi of America, Inc. Page 2 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin Figure 1. Positions of the cable ties. Note: You are not going to secure the harness to any part of the seat with the cable ties, you are only applying the cable ties to the harness to apply clamping force to the harness and shielding. DO NOT ATTACH THE HARNESS TO THE SEAT FRAME. 2. You will attach the first cable tie in the yellow marked area on the harness between the cable tie clip and the crossbar tube as shown below (Figure 2). © 2021 Audi of America, Inc. Page 3 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin Figure 2. Attach the first cable tie in the yellow area. 3. The second cable tie position is to the rear of the crossbar tube where the harness drops down from the frame. Place the cable tie in the yellow marked area shown below (Figure 3). © 2021 Audi of America, Inc. Page 4 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin Figure 3. Attach the second cable tie to the yellow marked area. Note: When tightening the cable ties, only tighten them with your hands, do not use any tools to tighten the cable tie as this can damage the harness. Check that the cable ties cannot be rotated on the harness by hand, to ensure that proper tension is achieved. Then cut off the excess length from the tie wrap. 4. Once you have the cable ties properly secured and installed, return the seat to the original position and clear the faults stored in the system. © 2021 Audi of America, Inc. Page 5 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin Q5 1. To apply the cable ties, the seat does not need to be removed. You will need to move the lateral seat adjustment all the way to rearmost adjustment limit and the vertical height adjustment all the way to the upper adjustment limit. Once the seat is adjusted to the above-mentioned position, you will see the need to attach the cable tie at two points on the harness as shown (Figure 4-6). Figure 4. Positions of the cable ties (front to back). © 2021 Audi of America, Inc. Page 6 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin Figure 5. Positions of the cable ties (back to front). Note: You are not going to secure the harness to any part of the seat with the cable ties, you are only applying the cable ties to the harness to apply clamping force to the harness and shielding. DO NOT ATTACH THE HARNESS TO THE SEAT FRAME. 2. You will attach the first cable tie in the yellow marked area on the harness between the cable tie clip and the crossbar tube (Figure 2). 3. The second cable tie position is to the rear of the black 8-pin connector (T8m) for the backrest and lumbar adjustment and in front of the harness push pin (Figure 6). © 2021 Audi of America, Inc. Page 7 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin Figure 6. Position of second cable tie behind the 8-pin connector. Note: When tightening the cable ties, only tighten them with your hands, do not use any tools to tighten the cable tie as this can damage the harness. Check that the cable ties cannot be rotated on the harness by hand, to ensure that proper tension is achieved. Then cut off the excess length from the tie wrap. © 2021 Audi of America, Inc. Page 8 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 4. Once you have the cable ties properly secured and installed, return the seat to the original position and clear the faults stored in the system. Warranty Claim Type: • 110 up to 48 Months/50,000 Miles. • G10 for CPO Covered Vehicles – Verify Owner. • If the vehicle is outside any warranty, this Technical Service Bulletin is informational only. Service Number: 7210 Damage Code: 0018 Labor Operations: Seat Wiring Harness Repair 7210 9999 25 TU Diagnostic Time: GFF – Checking and clearing fault codes 0150 0000 20 TU Road test prior to service procedure No allowance 0 TU Road test after service procedure No allowance 0 TU Claim Comment: As per TSB 2051242/6 All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty. Required Parts and Tools Always check with your Parts Department and/or ETKA for the latest information and parts bulletins. Part Number Part Description Quantity N 90937702 Cable strap 02 © 2021 Audi of America, Inc. Page 9 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin See ETKA Fasteners, Bolts, Nuts, and Screws as needed per the See ETKA/ELSA Repair Manual Additional Information All parts and service references provided in this TSB (2051242) are subject to change and/or removal. ©2022 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. © 2021 Audi of America, Inc. Page 10 of 10 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.