ITB22-014
Service Bulletin Details
Public Details for: ITB22-014
Enabling wireless apple carplay® features service information to enable wireless use of current apple carplay® features, follow the service procedure in this bulletin. Note: depending on the software version, the av control unit may
Models from 2021
2021 INFINITI Q50 |
2021 INFINITI Q60 |
2021 INFINITI QX50 |
Models from 2020
2020 INFINITI Q50 |
2020 INFINITI Q60 |
2020 INFINITI QX50 |
Classification: Reference: Date: AN22-009 ITB22-014 March 31, 2022 ENABLING WIRELESS APPLE CARPLAY® FEATURES APPLIED VEHICLES: 2020-2021 Q50 (V37) 2020-2021 Q60 (CV37) 2020-2021 QX50 (J55) SERVICE INFORMATION To enable wireless use of current Apple CarPlay® features, follow the SERVICE PROCEDURE in this bulletin. NOTE: Depending on the software version, the AV control unit may need to be updated. Perform steps 1-4 to check the software version. Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. 1/21 REQUIRED SPECIAL TOOL One of special tool USB drive J-52727-1 was previously shipped to each retailer and should already be available (Figure 1). Do not use any other USB drive to perform the procedure in this bulletin. Additional USB drives may be purchased from Tech•Mate: infinititechmate.com or 1-800-662-2001. The update-software only needs to be downloaded once, and can then be used continuously on multiple APPLIED VEHICLES. The update-software must be the only file on the USB drive. HINT: Figure 1 2/21 ITB22-014 SERVICE PROCEDURE IMPORTANT: Configuration of the audio unit (steps 27 - 45 on pages 10 - 17) is required after the software update (if performed). If the configuration steps are not completed, the wireless CarPlay will not operate. Check the Software Version 1. Press and hold the AUDIO button while, at the same time, rotating the volume knob left-rightleft. Figure 2 2. Select Confirmation/Adjustment. Figure 3 3. Select Version Information. Figure 4 3/21 ITB22-014 4. Confirm the Software Version. If the Software Version (digits 6-9, as shown in Figure 5) is lower than xxxxx2992x, select the back button and proceed to step 5 on page 5. If the Software Version is xxxxx2992x or higher (digits 6-9), select the back button and skip to step 27 on page 10 to configure the AV control unit for wireless CarPlay. Back button Figure 5 4/21 ITB22-014 Update the AV Control Unit (if needed) IMPORTANT: Before starting, make sure: ASIST is connected to the internet. ASIST has been synchronized (updated) to the current date. NOTE: In the following steps, if more than one CONSULT PC is available and the “PVI002” infotainment update-software has already been downloaded through ASIST to one of them, use the CONSULT PC with the pre-existing download. 5. Insert special tool USB drive J-52727-1 into a CONSULT PC. If the infotainment software has already been downloaded onto special tool USB drive J-52727-1 from a prior service procedure, skip to step 14 on page 7. HINT: o Special tool USB drive J-52727-1 is the only USB drive approved for use with this procedure. o The initial download of the update-software to the CONSULT PC and file transfer to the USB drive is estimated to take 6 hours. After the initial download of the update-software, file transfer to the USB drive is estimated to take 1 hour. o The update-software must be the only file on the USB drive. 6. Open ASIST. 7. Select Specialty Tools, and then select Infotainment Software Updates. Specialty Tools Infotainment Software Updates Figure 6 5/21 ITB22-014 8. Select the check box next to the “PVI002” Infotainment update-software (Figure 7). 9. Use the drop-down menu and select the location of the USB drive that was inserted in step 5 on page 5. Check box D:\ USB drive location PVI002 Infotainment update-software “Transfer” displays here if Infotainment update-software is already downloaded Drop-down menu Figure 7 10. Select Download, and then wait for the download to complete. If the PVI002 infotainment update-software has already been downloaded, “Transfer” will be displayed instead of “Download” when the infotainment software update box is checked. HINT: o The initial download of the update-software to the CONSULT PC and file transfer to the USB drive is estimated to take 6 hours. After the initial download of the update-software, file transfer to the USB drive is estimated to take 1 hour. o If while attempting to download the update-software to the CONSULT PC, you receive the message shown in Figure 8: a. First attempt to clear space on the CONSULT PC hard drive (40 GB required). b. If space cannot be cleared and a second CONSULT PC is available with space, use it and start over from step 5 on page 5. Figure 8 6/21 ITB22-014 11. Select OK. Figure 9 12. Once the transfer is complete, safely remove the USB drive from the CONSULT PC. a. From the PC toolbar, select the Safely Remove Hardware icon. o The icon is on the toolbar, or can be found after selecting the arrow. b. Select the USB drive to be removed, and then remove the USB drive from the CONSULT PC. Follow the steps to safely remove the USB drive. If not followed, the USB drive may corrupt the infotainment update-software. o If you are not familiar with the process of safe USB drive removal, ask for assistance at your retailer. Safely Remove Hardware icon Arrow on toolbar Figure 10 13. Close all ASIST Infotainment Software Update screens. 14. Set the parking brake. 15. Start the engine, and then wait 60 seconds for the system to load. HINT: The engine needs to idle for the duration of the update to retain battery charge. 7/21 ITB22-014 16. Insert the USB drive with the infotainment update-software into the vehicle’s USB media port (Figure 11). HINT: Charging ports are marked in the vehicle with a “lightning bolt” symbol (Figure 12). Do not insert the USB drive into a charging port. If used, the update-software and/or USB drive may become damaged. Only insert the USB drive in a USB media port. Do not remove the USB drive during the update to the vehicle until instructed to. If the USB drive is removed during the update, the audio unit may become damaged. USB media port symbol DO NOT USE USB ports with a “lightning bolt” Figure 11 17. Figure 12 Wait for the update to complete. Follow the on-screen instructions while waiting. HINT: The update lasts 15-25 minutes. Figure 13 18. Once the update is complete (Figure 14), remove the USB drive; the system will reboot (restart). HINT: The system will not reboot until the USB drive is removed. Figure 14 8/21 ITB22-014 Steps 19 - 26 must be completed. If they are not completed, the update may become corrupted. 19. Allow the reboot to complete (approximately 30 seconds). The Infiniti logo will be displayed during the reboot. Figure 15 20. Turn the ignition OFF. The steps below will fully reboot the infotainment system twice. 21. Open and close the driver (LH) door, and then ensure that all doors are closed. 22. Wait 5 minutes. Ensure that all doors remain closed during the 5-minute wait period. If a door is opened during the 5-minute wait period, the update may not complete and the AV control unit may become inoperable. HINT: The engine does not need to be running for the next steps. 23. Turn the ignition ON (engine OFF) and wait for the Infiniti logo to appear (Figure 15). 24. After the Infiniti logo appears, wait about 1 minute. 25. If the Infiniti logo does not appear (this might take up to 30 seconds), start over from step 20. The MENU (Home) screen in Figure 16 will be displayed. Turn OFF the ignition. Figure 16 26. Repeat steps 21 - 25 one more time (for a total of two [2] times) to complete the update. 9/21 ITB22-014 Configure AV Control Unit for Wireless CarPlay 27. Connect a battery maintainer/smart charger to the vehicle. 28. Connect the VI to the vehicle. 29. Start C-III plus. 30. Wait for the VI to be recognized (Figure 17). 31. The serial number will display when the VI is recognized. Select Re/programming, Configuration. The VI is recognized Figure 17 10/21 ITB22-014 32. Check the box to confirm the precaution instructions have been read, and then select Next. NOTE: Use the arrows (if needed) to view and read all the precautions. Figure 18 33. Select Manual Selection(Vehicle Name), select the applicable Vehicle Name and Model Year, and then select Select. EXAMPLE Figure 19 11/21 ITB22-014 34. Confirm the VIN or Chassis # is correct, and then select Confirm. XXXXXXXXXXX QX50 Figure 20 35. Confirm the VIN is correct for the vehicle, and then select Confirm. XXXXXXXXXXXXXXXXX Figure 21 12/21 ITB22-014 36. Select MULTI AV. Figure 22 37. Select Before ECU Replacement under VEHICLE CONFIGURATION. Figure 23 13/21 ITB22-014 38. Scroll through each of the pages of configuration items and write down each Item and Setting Value. If a printer is connected to the CONSULT PC, you may select Print. IMPORTANT: Write down or print all the configuration settings, as these settings will be used in step 42 on page 15. EXAMPLE Figure 24 39. After the current configurations have been written down or printed, select Back in the upper LH corner of the screen (Figure 24). 40. Select After ECU Replacement under VEHICLE CONFIRGURATION. Figure 25 14/21 ITB22-014 41. Select Manual selection. Figure 26 42. Use the drop down menus to select the configuration options that were printed or written down in step 38 on page 14, and then select Next. IMPORTANT: The default Setting Value for Wireless CarPlay is “WITHOUT”. Be sure to change this Setting Value to “WITH” (Figure 27). Wireless CarPlay For Wireless CarPlay, change Setting Value to “WITH” Figure 27 15/21 ITB22-014 43. Confirm the configuration displayed is correct, and then select OK. IMPORTANT: Be sure the Setting Value for Wireless CarPlay is “WITH” before selecting OK. Wireless CarPlay Figure 28 44. Allow the configuration to transfer to the vehicle. Wireless CarPlay Figure 29 16/21 ITB22-014 45. Select End. Figure 30 Erase DTCs 46. Select Diagnosis (All Systems). Figure 31 17/21 ITB22-014 47. Select Automatic Selection(VIN). EXAMPLE Figure 32 48. Allow the CONSULT to perform automatic VIN selection. Figure 33 18/21 ITB22-014 49. Confirm the VIN or Chassis # is correct, and then select Confirm. XXXXXXXXXXX QX50 Figure 34 50. Select ERASE. Figure 35 19/21 ITB22-014 51. Select Execute. Figure 36 52. Select Close. Figure 37 53. Close C-III plus. 54. Remove the VI from the vehicle. 55. Disconnect the battery maintainer/smart charger. 20/21 ITB22-014 AMENDMENT HISTORY PUBLISHED DATE REFERENCE March 31, 2022 ITB22-014 DESCRIPTION Original bulletin published 21/21 ITB22-014