TSB009021Rev2

T-SB-0090-21
Rev2
October 28, 2021
2022 Tundra Pre-Delivery Service (PDS)
Service
Category
General
Section
Pre-Delivery Service
Market USA
Applicability
YEAR(S)
MODEL(S)
2022
Tundra
ADDITIONAL INFORMATION
REVISION NOTICE
April 20, 2022 Rev2:
 The Warranty Information section has been updated.
January 18, 2022 Rev1:
 The Set Hybrid Radio Feature to “OFF” and Navigation — “Set Date & Time by GPS” sections
have been included.
 The Entune™ 3.0 App Suite Connect Initialization/Update section has been excluded.
Any previous printed versions of this bulletin should be discarded.
Introduction
Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer
feedback indicates the following areas deserve special attention when performing PDS:




Careful inspection for paint chips/scratches and body dents/dings.
Proper operation of electrical accessories (including interior light, clock, and radio reset).
Interior cleanliness.
Proper function of mechanical systems.
Customer retention and proper maintenance of vehicles are and have always been a major focus
for Toyota. To help remind customers that regular service is essential to the proper maintenance
of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing
this, customers will be reminded to return to your dealership for service. Your current service
reminder sticker may be used. (See PDS Check Sheet item 8 of “Final Inspection and Cleaning.”)
This bulletin contains the PDS procedures that apply specifically to 2022 model year Tundra
vehicles. A universal PDS Check Sheet that contains PDS steps that apply to all 2022 model year
Toyota vehicles has been developed. To properly perform a complete PDS, you must complete
all procedures contained in this TSB as well as the universal PDS Check Sheet.
In addition, if the vehicle is stored for over 30 days, be sure to follow Long-Term Vehicle
Storage Guidelines.
© 2021 Toyota Motor Sales, USA
Page 1 of 5
T-SB-0090-21
Rev2
October 28, 2021
Page 2 of 5
2022 Tundra Pre-Delivery Service (PDS)
Warranty Policy
If the need for additional repairs or adjustment is noted during PDS, the required service should
be performed under warranty. Reimbursement will be managed under the warranty policy.
The Warranty Policy and Procedures Manual requires that you maintain the completed
Check Sheet in the customer’s file. If you cannot produce a completed form for each retailed
vehicle upon TMS and/or Region/Distributor audit, the PDS payment amount will be subject
to debit.
An additional Repair Order completed in conjunction with normal PDS MUST have time
punch/flags for service. If multiple repairs are performed, separate time flags MUST be punched
for each repair.
Warranty Information
OP CODE
DESCRIPTION
MODEL
TIME
OFP
T1
T2
001013
Pre-Delivery Service (PDS)
Tundra
0.9
–
–
–
Required Tools & Equipment
REQUIRED EQUIPMENT
SUPPLIER
Techstream ADVi*
QTY
TSADVUNIT
Techstream 2.0
Techstream Lite
PART NUMBER
TS2UNIT
ADE
Techstream Lite (Green Cable)
TSLITEPDLR01
TSLP2DLR01
*Essential SST.
NOTE
 Only ONE of the Techstream units listed above is required.
 Software version 17.00.020 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.
© 2021 Toyota Motor Sales, USA
1
T-SB-0090-21
Rev2
October 28, 2021
Page 3 of 5
2022 Tundra Pre-Delivery Service (PDS)
Procedures

D/C Cut Fuse Installation ....................................................................................................... 3

Seating Position Control ECU Initialization ............................................................................. 4

Front License Plate and Mounting Bracket Installation* .......................................................... 4

Set Hybrid Radio Feature to OFF ........................................................................................... 4

Navigation — Set Date & Time by GPS ................................................................................. 5

Tire Pressure Warning System (TPWS) Initialization .............................................................. 5
*If applicable.
D/C Cut Fuse Installation
To minimize battery discharge, the D/C cut fuse (30A) has been removed and is stored in the
engine compartment relay block. Install the D/C cut fuse (30A) and confirm ALL related
Diagnostic Trouble Codes (DTCs) are cleared.
Figure 1.
1
3
2
1
Relay Block
2
Remove D/C Cut Fuse (30A)
3
Install D/C Cut Fuse (30A)
© 2021 Toyota Motor Sales, USA
T-SB-0090-21
Rev2
October 28, 2021
Page 4 of 5
2022 Tundra Pre-Delivery Service (PDS)
Seating Position Control ECU Initialization
Refer to the applicable Repair Manual for the seating position control ECU
initialization procedure (procedure 2).
Front License Plate and Mounting Bracket Installation
1. Align the holes on the license plate mounting bracket with the dimples on the front of
the bumper.
NOTICE
Do NOT drill holes through the front bumper or overtighten the self-tapping screws.
2. Install two long self-tapping screws through the recessed holes on the license plate mounting
bracket and screw them through the bumper.
3. Insert the license plate onto the tabs on the license plate mounting bracket.
4. Align the holes on the license plate with the holes on the license plate mounting bracket.
5. Install one short self-tapping screw through the driver side license plate hole extending into the
license plate mounting bracket.
6. Install one short self-tapping screw through the passenger side license plate hole extending
into the license plate mounting bracket.
Set Hybrid Radio Feature to OFF
Without a Wi-Fi subscription, the customer will receive a “Subscription Required” pop-up while in
weak broadcast radio signal areas. This pop-up notification may cause confusion to the customer.
Therefore, it is necessary to toggle the Hybrid Radio feature to the OFF position.
1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Navigate the following menus in the head unit: Settings – Sound and Media – Radio –
Hybrid Radio.
3. Ensure the Hybrid Radio feature is set to the OFF position.
NOTE
The Enable Hybrid Radio feature is factory preset to the ON position.
© 2021 Toyota Motor Sales, USA
T-SB-0090-21
Rev2
October 28, 2021
Page 5 of 5
2022 Tundra Pre-Delivery Service (PDS)
Navigation — Set Date & Time by GPS
Before selling a Toyota vehicle, it is necessary to turn the Set Date & Time by GPS setting to the
ON position.
1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Navigate the following menus in the head unit: Settings – General – Date & Time –
Set date & time by GPS.
3. Ensure the Set Date & Time by GPS function is set to the ON position.
Tire Pressure Warning System (TPWS) Initialization
Refer to the applicable Repair Manual for the TPWS initialization procedure. Note the spare tire
does NOT have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop
temperature, perform a Health Check using Techstream and select the compensation tire pressure
checkbox. Compensation pressures will display on the Health Check results screen. Adjust the tire
pressure when the tires are cold.
© 2021 Toyota Motor Sales, USA