A22-022
Service Bulletin Details
Public Details for: A22-022
Service bulletin - cruise control is not working and all the acc lights are illuminated with dtc B2A60-96, multipurpose camera unit hardware malfunction. Software issues with the multipurpose camera.
- 2022 -
Models from 2022
2022 HONDA CIVIC |
Service Bulletin 22-022 June 24, 2022 Version 1 ACC Warning Light Is On With DTC B2A60-96 AFFECTED VEHICLES Year Model Trim VIN Range 2022 Civic Sedan LX 2HGFE2F2.NH500001 thru 2HGFE2F2.NH584673 2022 Civic Sedan Sport 2HGFE2F5.NH500002 thru 2HGFE2F5.NH586203 2022 Civic Sedan EX 2HGFE1F7.NH302433 thru 2HGFE1F7.NH321367 2022 Civic Sedan Sport Touring 2HGFE1F9.NH300001 thru 2HGFE1F9.NH321070 2022 Civic Sedan Si 2HGFE1E5.NH470001 thru 2HGFE1E5.NH473860 SYMPTOM Cruise control is not working and all the ACC lights are illuminated with DTC B2A60-96, Multipurpose Camera Unit Hardware Malfunction. POSSIBLE CAUSE Software issues with the multipurpose camera. CORRECTIVE ACTION Update the driver support software to the most current software version. WARRANTY CLAIM INFORMATION The normal warranty applies. Operation Number Description Flat Rate Time Defect Code Symptom Code Template ID Failed Part Number 4815D2 Update the ACC/CMBS Software. 0.2 hr 03214 03217 A22022A 36163-T20-A04 CUSTOMER INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. © 2022 American Honda Motor Co., Inc. — All Rights Reserved Page 1 of 10 SOFTWARE INFORMATION NOTE: Unnecessary or incorrect repairs resulting from a failure to update the diagnostic and reprogramming software are not covered under warranty. Before beginning the repair, make sure all diagnostic and reprogramming software are updated as listed. i-HDS Software Version 1.006.062 or later HDS Software Version 3.104.047 or later J2534 Rewrite Software Information PC Application Version 1.00.0034 Database Update 31-MAY-2022 or later NoticeDB Version 31-MAY-2022 or later Update only the systems and software listed in this service bulletin. Do not use the MongoosePRO VCI for this service bulletin as it is not an American Honda-approved device. For more information about updating vehicle systems, refer to service bulletin 01-023, Updating Control Units/Modules. Year/Model Vehicle System Program ID (or later) 2022 Civic Sedan ACC/CMBS 36161-T20-A080 2022 Civic Hatchback ACC/CMBS 36161-T47-A070 2022 Civic Si Sedan ACC/CMBS 36161-T38-A070 INSPECTION PROCEDURE Connect the i-HDS and check for DTC’s. • If DTC B2A60-96, Multipurpose Camera Unit Hardware Malfunction is found, clear and recheck. • If the DTC remains cleared, proceed to the Repair Procedure and update the ACC/CMBS software. • If the DTC does not clear, continue with normal troubleshooting. REPAIR PROCEDURE • Make sure the 12-volt battery is fully charged before starting an update. • Connect a fully charged jumper battery to the vehicle, and leave it connected during the entire procedure to maintain steady voltage. • Do not use the GR8 because the vehicle requires a steady electrical current. • Control module failure caused by the improper completion of a software update (early key cycle, low battery voltage, disconnected DLC cable, etc.) is not covered by warranty. • If an error occurs during the update or the i-HDS freezes, do not disconnect the battery or turn the ignition to OFF. Reboot the i-HDS, and start over. • To prevent control unit damage, do not operate anything electrical (headlights, audio system, brakes, A/C, power windows, door locks, etc.) during the update. • Warranty reimbursement for technician labor is not allowed for routine checking/installation of any available software update. • High temperature in the engine compartment might cause the VSA modulator-control unit to become too hot to run the update. If the engine has been running before this procedure, open the hood and cool the engine compartment. Page 2 of 10 • Do an ALL DTC Check to clear any codes that may have set during the update. NOTE: When doing this update on vehicles with the 9" center display, certain system messages may appear on the screen after the update. This is normal and the messages will clear after a few minutes once the ignition is placed in IGII or in the run position. 1. From the desktop, select i-HDS. 2. From the HOME menu, select the J2534 Rewrite. Page 3 of 10 3. When prompted select Start, do not enter a service bulletin number. NOTE: Under certain conditions the HOME menu screen may come up. If it does, just minimize it to show the screen under it. 4. Connect the i-HDS to the vehicle and select Start to begin reprogramming. Page 4 of 10 5. Follow the screen prompts, then select Next. Page 5 of 10 6. Enter the VIN and repair order number. Then, select Next. Page 6 of 10 7. Select the ACC/CMBS, and then Select. NOTE: Wait until vehicle communication has completed. 8. Confirm the update information, then select ENTER to proceed. Page 7 of 10 9. Select ENTER to begin reprogramming, and follow the screen prompts. Page 8 of 10 Page 9 of 10 10. Once the module is updated, the following screen appears, then select EXIT. 11. Do an ALL DTC Check then clear any codes set during the update. 12. Place the ignition in IGII and leave it in this mode until the warning lights are off, then turn the ignition to OFF and leave it for 15 seconds. 13. Repeat step 12 two additional times. 14. Once the three ignition cycles are complete, place the ignition in IGII and check for any illuminated sensing support warning lights. If none, the update is complete and successful. 15. If Sensing support lights illuminate and B2A60-96 returns, continue with normal trouble shooting. NOTE: When doing this update on vehicles with the 9" center display, certain system messages may appear on the screen after the update. This is normal and the messages will clear after a few minutes once the ignition is placed in IGII or in the run position. END Page 10 of 10