131520275854

Technical Service Bulletin
21 Rattling/jarring noise from engine - 2.0 TFSI EA888 transverse
21 13 15 2027585/4 June 24, 2013. Supersedes Technical Service Bulletin Group 21 number 12-09 dated May 16,
2012 for reasons listed below.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
A3
2008 - 2013
All
CCTA, CBFA engines
TT
2008 - 2014
All
CCTA, CETA engines
Condition
REVISION HISTORY
Revision
Date
Purpose
4
-
Revised header data (Added model years)
3
5/16/2012
Revised Warranty (Updated time units)
2
3/6/2012
Revised Warranty
1
11/14/2011
Original publication
Rattling and/or jarring noises heard from the engine compartment/exhaust system between 1800 and 2900 rpm.
Technical Background
Because of exhaust gas pulsations, the wastegate flap and rods vibrate at the start of the boost air control. This
vibration causes rattling or jarring noises.
Production Solution
Not applicable.
© 2013 Audi of America, Inc.
Page 1 of 6
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Service
A spring clip (06J145220A) must be fitted on the wastegate
adjustment (Figure 1).
Figure 1. Spring clip
On vehicles with front wheel drive:
1.
Remove the noise damping according to the instructions in Elsa: Repair Manual >> Body >> Body Exterior
>> 50 Body Front >> Removal and Installation >> Noise Insulation.
2.
Remove the drive shaft protection.
3.
Fit the clip from the side (Figure 2).
Figure 2. Wastegate linkage with clip fitted
from the side.
© 2013 Audi of America, Inc.
Page 2 of 6
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
4.
Turn the clip to the left until the lugs slot in (Figure 3).
Figure 3. Wastegate linkage with clip in final
position.
On vehicles with four wheel drive (Quattro):
1.
Remove the propshaft heat shield according to the instructions in Elsa: Repair Manual >> Body >> 66
Exterior Equipment >> Removal and Installation >> Underbody Trim Panels >>Heat Shields, Driveshaft
2.
Reach through from behind to position the clip (Figure 4).
Figure 4. Reach through and position clip.
© 2013 Audi of America, Inc.
Page 3 of 6
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
3.
Fit the spring clip on the wastegate adjustment (Figure 5).
Figure 5. Fit the spring clip on the wastegate
adjustment.
Tip: The spring tip must not be overstretched. The
maximum opening of the spring clip is 14 mm. In the
example in the image, the opening is approximately 10.5
mm (Figure 6).
The spring clip must be replaced after every removal.
Figure 6. (1) Maximum opening of spring
clip.
© 2013 Audi of America, Inc.
Page 4 of 6
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
4.
After fitting the spring clip, check for correct fit (Figure 7).
Figure 7. Spring clip correct fitting.
5.
Check the position of the original circlip (Figure 8), and
correct if necessary.
Figure 8. (2) Position of the original circlip.
© 2013 Audi of America, Inc.
Page 5 of 6
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Warranty
Claim Type:
Use applicable claim type. If vehicle is outside any warranty, this Technical Service
Bulletin is informational only.
Service Number:
2130
Damage Code:
0018
Labor Operations:
Remove and install sound protection tray
1082 1900
20 TU
Remove and install heat shield (Quattro Only)
3970 1999
10 TU
Install spring clip
2130 2199
10 TU
GFF
No allowance
0 TU
Road test prior to service procedure
0121 0002
10 TU
Road test after service procedure
0121 0004
10 TU
Diagnostic Time:
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:
As per TSB #2027585/4
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Required Parts and Tools
Part Number
Part Description
Quantity
06J145220A
Spring clip
1
Additional Information
All parts and service references provided in this TSB are subject to change and/or removal. Always check with
your Parts Department and service manuals for the latest information.
© 2013 Audi of America, Inc.
Page 6 of 6
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.