A22-022

Service Bulletin
22-022
July 15, 2022
Version 2
ACC Warning Light Is On With DTC B2A60-96
Supersedes 22-022, dated June 24, 2022, to update the information highlighted in yellow.
AFFECTED VEHICLES
Year
Model
Trim
VIN Range
2022
Civic Sedan
LX
2HGFE2F2.NH500001 thru 2HGFE2F2.NH584673
2022
Civic Sedan
Sport
2HGFE2F5.NH500002 thru 2HGFE2F5.NH586203
2022
Civic Sedan
EX
2HGFE1F7.NH302433 thru 2HGFE1F7.NH321367
2022
Civic Sedan
Sport Touring
2HGFE1F9.NH300001 thru 2HGFE1F9.NH321070
2022
Civic Sedan
Si
2HGFE1E5.NH470001 thru 2HGFE1E5.NH473860
2022
Civic Hatchback
LX
19XFL2H5.NE000002 thru 19XFL2H5.NE016807
2022
Civic Hatchback
Sport CVT
19XFL2H8.NE000001 thru 19XFL2H8.NE022700
2022
Civic Hatchback
Sport MT
19XFL2G8.NE000003 thru 19XFL2G8.NE022701
2022
Civic Hatchback
EX-L
19XFL1H7.NE000004 thru 19XFL1H7.NE021755
2022
Civic Hatchback
Sport Touring
CVT
19XFL1H8.NE000007 thru 19XFL1H8.NE021756
2022
Civic Hatchback
Sport Touring MT 19XFL1G8.NE000003 thru 19XFL1G8.NE021533
REVISION SUMMARY
Under AFFECTED VEHICLES, the 2022 Civic Hatchback was added.
SYMPTOM
Cruise control is not working and all the ACC lights are illuminated with DTC B2A60-96, Multipurpose Camera Unit
Hardware Malfunction.
POSSIBLE CAUSE
Software issues with the multipurpose camera.
CORRECTIVE ACTION
Update the driver support software to the most current software version.
CUSTOMER INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume
this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an
authorized Honda automobile dealer.
©
2022 American Honda Motor Co., Inc. — All Rights Reserved
Page 1 of 10
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation
Number
Description
Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
4815D2
Update the ACC/CMBS
Software.
0.2 hr
03214
03217
A22022A
36163-T20-A04
SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from a failure to update the diagnostic and reprogramming software
are not covered under warranty.
Before beginning the repair, make sure all diagnostic and reprogramming software are updated as listed.
i-HDS Software Version
1.006.062 or later
HDS Software Version
3.104.047 or later
J2534 Rewrite Software Information
PC Application Version
1.00.0034
Database Update
31-MAY-2022 or later
NoticeDB Version
31-MAY-2022 or later
Update only the systems and software listed in this service bulletin.
Do not use the MongoosePRO VCI for this service bulletin as it is not an American Honda-approved device.
For more information about updating vehicle systems, refer to service bulletin 01-023, Updating Control Units/Modules.
Year/Model
Vehicle System
Program ID (or later)
2022 Civic Sedan
ACC/CMBS
36161-T20-A080
2022 Civic Hatchback
ACC/CMBS
36161-T47-A070
2022 Civic Si Sedan
ACC/CMBS
36161-T38-A070
INSPECTION PROCEDURE
Connect the i-HDS and check for DTC’s.
•
If DTC B2A60-96, Multipurpose Camera Unit Hardware Malfunction is found, clear and recheck.
•
If the DTC remains cleared, proceed to the Repair Procedure and update the ACC/CMBS software.
•
If the DTC does not clear, continue with normal troubleshooting.
REPAIR PROCEDURE
•
Make sure the 12-volt battery is fully charged before starting an update.
•
Connect a fully charged jumper battery to the vehicle, and leave it connected during the entire procedure to maintain
steady voltage.
•
Do not use the GR8 because the vehicle requires a steady electrical current.
•
Control module failure caused by the improper completion of a software update (early key cycle, low battery voltage,
disconnected DLC cable, etc.) is not covered by warranty.
Page 2 of 10
•
If an error occurs during the update or the i-HDS freezes, do not disconnect the battery or turn the ignition to
OFF. Reboot the i-HDS, and start over.
•
To prevent control unit damage, do not operate anything electrical (headlights, audio system, brakes, A/C, power
windows, door locks, etc.) during the update.
•
Warranty reimbursement for technician labor is not allowed for routine checking/installation of any available
software update.
•
High temperature in the engine compartment might cause the VSA modulator-control unit to become too hot to run
the update. If the engine has been running before this procedure, open the hood and cool the engine compartment.
•
Do an ALL DTC Check to clear any codes that may have set during the update.
NOTE: When doing this update on vehicles with the 9" center display, certain system messages may appear on the
screen after the update. This is normal and the messages will clear after a few minutes once the ignition is placed in
IGII or in the run position.
1. From the desktop, select i-HDS.
2. From the HOME menu, select the J2534 Rewrite.
Page 3 of 10
3. When prompted select Start, do not enter a service bulletin number.
NOTE: Under certain conditions the HOME menu screen may come up. If it does, just minimize it to show the
screen under it.
4. Connect the i-HDS to the vehicle and select Start to begin reprogramming.
Page 4 of 10
5. Follow the screen prompts, then select Next.
Page 5 of 10
6. Enter the VIN and repair order number. Then, select Next.
Page 6 of 10
7. Select the ACC/CMBS, and then Select.
NOTE: Wait until vehicle communication has completed.
8. Confirm the update information, then select ENTER to proceed.
Page 7 of 10
9. Select ENTER to begin reprogramming, and follow the screen prompts.
Page 8 of 10
Page 9 of 10
10. Once the module is updated, the following screen appears, then select EXIT.
11. Do an ALL DTC Check then clear any codes set during the update.
12. Place the ignition in IGII and leave it in this mode until the warning lights are off, then turn the ignition to OFF and
leave it for 15 seconds.
13. Repeat step 12 two additional times.
14. Once the three ignition cycles are complete, place the ignition in IGII and check for any illuminated sensing support
warning lights. If none, the update is complete and successful.
15. If Sensing support lights illuminate and B2A60-96 returns, continue with normal trouble shooting.
NOTE: When doing this update on vehicles with the 9" center display, certain system messages may appear on the
screen after the update. This is normal and the messages will clear after a few minutes once the ignition is placed in IGII
or in the run position.
END
Page 10 of 10