22G05
Service Bulletin Details
Public Details for: 22G05
Certain 2022 model year f-150 and super duty vehicles exterior badge retrofit due to a supplier shortage of exterior vehicle badges, some 2022 model year f-150 and super duty vehicles will be shipped and can be sold to customers with tempo
- 2022 -
Models from 2022
2022 FORD F-150 |
2022 FORD F-250 SD |
2022 FORD F-350 SD |
2022 FORD F-450 SD |
2022 FORD F-550 SD |
Stacy L. Balzer Operating Director Service Engineering Operations Ford Customer Service Division Ford Motor Company P. O. Box 1904 Dearborn, Michigan 48121 October 21, 2022 TO: All U.S. Ford and Lincoln Dealers SUBJECT: Recommended Delivery Hold Component Installation Program 22G05 Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit REF: EFC - Supersede of Product Offering Changes: 22MY F150 & Super Duty Temporary Exterior Vehicle Badges Dated: September 30, 2022 F-150 Customer Acknowledgement Form Super Duty Customer Acknowledgement Form PROGRAM TERMS This program will be in effect through October 31, 2032, or a maximum of 150,000 miles, whichever occurs first. If a vehicle already has accumulated more than 150,000 miles, this coverage will last through October 31, 2023. AFFECTED VEHICLES Vehicle Model Year F-150 2022 Super Duty 2022 Assembly Plant Build Dates Dearborn Beginning July 28, 2022 Kansas City Beginning July 31, 2022 Kentucky Beginning July 23, 2022 Ohio Beginning August 11, 2022 Affected vehicles are identified in OASIS and FSA VIN Lists. NOTE: The list of affected VINs may be updated daily as vehicles are added to the program. End build dates will be provided once they are established at all assembly plants. NOTE - Verify VIN status: Some vehicles may be in the process of being repaired at the plant. Monitor OASIS before opening an RO and/or beginning a repair. Parts purchased for an FSA can be returned for credit, if required. See the EXCESS STOCK RETURN details in Attachment II for more information. Copyright 2022 Ford Motor Company REASON FOR THIS PROGRAM Due to a supplier shortage of exterior vehicle badges, some 2022 Model Year F-150 and Super Duty vehicles will be shipped and can be sold to customers with temporary or missing badges. Temporary/missing badges will not impact the vehicle performance or function. Trucks may not have the same number of temporary badges and/or missing badges. All temporary badges will be molded in color black. • F150 - Temporary F-150 badges could include both side fender vent nameplate/trim badges (e.g., molded in color black in place of F-150/XLT). Missing badges could include both door powertrain badges (e.g., PowerBoost), XLT Texas/Oklahoma badge and/or EcoBoost badge on tailgate, and/or King Ranch badge on tailgate. • Super Duty - Temporary Super Duty badges could include both side fender vent nameplate/trim badges (e.g., molded in color black in place of F-250/Lariat). Missing badges could include both door powertrain badges (e.g.,6.7L Power Stroke), and/or King Ranch badge on tailgate. Customers will be required to sign an acknowledgement letter, notifying them of the temporary or missing badges prior to vehicle sale. Reference: Electronic Field Communication (EFC) - Supersede of Product Offering Changes: 22MY F150 & Super Duty Temporary Exterior Vehicle Badges. SERVICE ACTION Dealers will install missing badges for all impacted 2022 Model Year F-150 and Super Duty customers. New in-stock vehicles: install badges prior to new vehicle delivery when possible. • Ford will place VIN specific orders for badges and ship them to delivering dealers. o VIN will be printed on the package label. o Dealers may look up a VIN specific list of missing badges at https://22g05badgecheck.com/ • For special or unique situations, (non-involved VIN, different badge count vs. shipped parts, damaged part, etc.) please use the SSSC contact selection Badge Inquiry. • Verify VIN status: Some vehicles may be in the process of being repaired at the plant. Monitor OASIS before opening an RO and/or beginning a repair. Dealers are to install the missing badges per technical information – from 1 to 5 badges for F-150 or from 1 to 7 for Super Duty (vehicle specific). Dealers will also remove any temporary fender badges (side vents), clean surfaces, and install new badge(s) in the proper location(s). This service must be performed on all affected vehicles at no charge to the vehicle owner. To assist vehicle owners to have this update completed, dealers should: • Arrange for a mobile repair at the owner’s location, • Mobile service should be made available for all customers. Refer to the Claiming sections for further details. NOTE: Please notify the SSSC if vehicle is being dealer traded or otherwise delivered by another dealer (include new delivering Dealer in SSSC contact). NOTE: Ford Oval badges are not included in this program and should be considered a mis-build if missing. Copyright 2022 Ford Motor Company CUSTOMER NOTIFICATION Owners of record will be notified via first-class mail after parts supply is at launch levels - ordering information has been provided to dealers. Dealers should repair any affected vehicles that arrive at their dealerships, whether or not the customer has received a letter. ATTACHMENTS Attachment I: Attachment II: Attachment III: Attachment IV: Attachment V: Administrative Information Labor Allowances and Parts Ordering Information Technical Information – F150 Technical Information – Super Duty Mobile Service Record QUESTIONS & ASSISTANCE For questions and assistance, contact the Special Service Support Center (SSSC) via the SSSC Web Contact Site. The SSSC Web Contact Site can be accessed through the Professional Technician System (PTS) website using the SSSC link listed at the bottom of the OASIS VIN report screen or listed under the SSSC tab. Sincerely, Stacy L. Balzer Copyright 2022 Ford Motor Company ATTACHMENT I Page 1 of 3 Recommended Delivery Hold Component Installation Program 22G05 Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit MOBILE REPAIR RECOMMENDATIONS • Confirm with customer a mobile repair is feasible. • Check OASIS prior to going to the customer’s home or business to confirm if any other outstanding FSA needs to be completed. • Transportation – due to the simplicity of this repair, a specialty vehicle is not required. MOBILE REPAIR ADDITIONAL INFORMATION Please ensure the technician brings the following to the mobile repair destination: • Printed Technical Instructions. • Printed Repair/Work Order or any other necessary documentation as customer copy(s) o Documents could also be emailed to the customer. • Shirt/uniform and vehicle graphic with dealership or Ford logos are recommended. • Recommended tools and cleaning supplies: Plastic trim removal tool, isopropyl alcohol, microfiber cleaning cloths, and making tape. MOBILE REPAIR QUESTIONS AND ASSISTANCE • For questions and assistance, contact the Special Service Support Center (SSSC) via the SSSC Web Contact Site. Work with Dealership warranty administrator to create a SSSC contact ID#. • Once an SSSC agent responds to the new contact ID#, you may opt to call the SSSC hotline: (800) 325-5621. OASIS ACTIVATION OASIS will be activated on October 21, 2022. FSA VIN LISTS ACTIVATION FSA VIN Lists will begin to be available through https://web.fsavinlists.dealerconnection.com on October 21, 2022, and continuously updated as vehicles are added to the program. Owner names and addresses will be available once parts are in good status. NOTE: Your FSA VIN Lists may contain owner names and addresses obtained from motor vehicle registration records. The use of such motor vehicle registration data for any purpose other than in connection with this program is a violation of law in several states, provinces, and countries. Accordingly, you must limit the use of this listing to the follow-up necessary to complete this service action. SOLD VEHICLES • Owners of affected vehicles will be directed to dealers for repairs. • Immediately contact any of your affected customers whose vehicles are not on your VIN list but are identified in OASIS. Give the customer a copy of the Owner Notification Letter (when available) and schedule a service date. • Correct other affected vehicles identified in OASIS which are brought to your dealership. • Dealers are to prioritize repairs of customer vehicles over repairs of new and used vehicle inventory. Copyright 2022 Ford Motor Company ATTACHMENT I Page 2 of 3 Recommended Delivery Hold Component Installation Program 22G05 Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit STOCK VEHICLES • Correct all affected units in your new vehicle inventory before delivery. • Use OASIS to identify any affected vehicles in your used vehicle inventory. TITLE BRANDED / SALVAGED VEHICLES Affected title branded and salvaged vehicles are eligible for this service action. OWNER REFUNDS Refunds are not approved for this program. RENTAL VEHICLES Rental vehicles are not approved for this program. ADDITIONAL REPAIR (LABOR TIME AND/OR PARTS) Additional repairs identified as necessary to complete the FSA should be managed as follows: • For related damage and access time requirements, refer to the Warranty and Policy Manual – Section 6 – Ford/Lincoln Program Policies – Field Service Actions (FSA) – Related Damage. • For vehicles within new vehicle bumper-to-bumper warranty coverage, no SSSC approval is required. o Ford vehicles – 3 years or 36,000 miles For vehicles outside new vehicle bumper-to-bumper warranty coverage, submit an Approval Request to the SSSC Web Contact Site prior to completing the repair. CLAIMS PREPARATION AND SUBMISSION • Claim Entry: Enter claims using Dealer Management System (DMS) or One Warranty Solution (OWS) online. o When entering claims: Claim type 31: Field Service Action The FSA number 22G05 is the sub code Customer Concern Code (CCC): B60 – Exterior nameplate/badge troubles Condition Code (CC): 39 – Missing Part Causal Part Number: 16702, Part Quantity: 0 o For additional claims preparation and submission information, refer to the Recall and Customer Satisfaction Program (CSP) Repairs in the OWS User Guide. • Related Damage/Additional labor and/or parts: Must be claimed as Related Damage on a separate repair line from the FSA with same claim type and sub code as described in Claim Entry above. IMPORTANT: Click the Related Damage Indicator radio button. Copyright 2022 Ford Motor Company ATTACHMENT I Page 3 of 3 Recommended Delivery Hold Component Installation Program 22G05 Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit • • Special Allowances o Mobile service allowances can be claimed for dealer-performed mobile repairs. Dealers that are working with Ford-contracted mobile repair companies should refer to those companies for claiming instructions. o For dealer-performed mobile service, retain a copy of the Service Management signed record (see Attachment IV), with the repair order documentation. o Claim the mobile service allowance Labor Operation Code 22G05MM along with the applicable Labor Operation Code for the repair (refer to the Labor Allowances table in Attachment II). Provision for Locally Obtained Supplies: Includes isopropyl alcohol, cleaning cloths, and making tape that can be used for multiple vehicles. Submit on the same line as the repair. o Program Code: 22G05 o Misc. Expense: OTHER o Misc. Expense: Claim up to $3.50 Copyright 2022 Ford Motor Company ATTACHMENT II Page 1 of 3 Recommended Delivery Hold Component Installation Program 22G05 Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit LABOR ALLOWANCES Description General admin/processing (per Technical Information) and claimed with one or more of the following labor codes. Includes drive in/out. Both LH/RH Front Fender Vent Badge Install – expected to be in pairs. Remove Temporary Badge - Includes Cleaning Surfaces - Any Vehicle line LH - One Part - Front Door Badge Install (Peel-and-Stick) - F-150 Only (PowerBoost) - Includes Cleaning Surfaces RH - One Part - Front Door Badge Install (Peel-and-Stick) - F-150 Only (PowerBoost) - Includes Cleaning Surfaces LH - Two Parts - Front Door Badge Install (Peel-and-Stick) - Super Duty Only (6.7L Power Stroke) - Includes Cleaning Surfaces RH - Two Parts - Front Door Badge Install (Peel-and-Stick) - Super Duty Only (6.7L Power Stroke) - Includes Cleaning Surfaces One Tailgate Badge (Peel-and-Stick) - Includes Cleaning Surfaces - Any Vehicle Line - Cannot be claimed with H Two Tailgate Badges (Peel-and-Stick) - Includes Cleaning Surfaces - Any Vehicle Line - Cannot be claimed with G Mobile Service: Can be used when the repair takes place away from the dealership. If Additional Time is Required Due to Travel, Please Submit an SSSC Approval Form. Labor Operation Labor Time 22G05A 0.3 Hours 22G05B 0.1 Hours 22G05C 0.1 Hours 22G05D 0.1 Hours 22G05E 0.2 Hours 22G05F 0.2 Hours 22G05G 0.1 Hours 22G05H 0.2 Hours 22G05MM 0.5 Hours Copyright 2022 Ford Motor Company ATTACHMENT II Page 2 of 3 Recommended Delivery Hold Component Installation Program 22G05 Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit PARTS REQUIREMENTS / ORDERING INFORMATION NOTE: VIN specific part orders to be placed on behalf of dealers. Parts are not yet available to repair all vehicles. Until further notice, Dealers will be automatically shipped the appropriate badge parts per VIN. Dealers may look up a VIN specific list of missing badges at: o https://22g05badgecheck.com/ • For special or unique situations, (non-involved VIN, different badge count vs. shipped parts, collision repair, etc.) please use the SSSC contact selection Badge Inquiry. NOTE: Ford Oval badges are not included in this program and should be considered a mis-build if missing. • • • DEALER PRICE For latest prices, refer to DOES II. PARTS RETENTION, RETURN, & SCRAPPING Follow the provisions of the Warranty and Policy Manual, Section 1 - WARRANTY PARTS RETENTION AND RETURN POLICIES. If a replaced part receives a scrap disposition, the part must be scrapped in accordance with all applicable local, state and federal environmental protection and hazardous material regulations. Federal law prohibits selling motor vehicle parts or components that are under safety, compliance, or emissions recall. EXCESS STOCK RETURN Excess stock returned for credit must have been purchased from Ford Customer Service Division in accordance with Policy Procedure Bulletin 4000. REPLACED FSA PARTS INSPECTION AND SIGN OFF Effective March 1st 2021 all parts replaced as part of an FSA repair with a repair order open date of March 1st 2021 or later must be inspected and signed off on the repair order by a member of your dealers fixed operations management team or an employee the task has been delegated to. If the task is to be delegated to a non-management employee, the employee needs to be someone other than the technician who completed the repair and needs to understand the importance of completing this task consistently and accurately. • All parts replaced as part of an FSA repair should be returned to the parts department following the Warranty Parts Retention and Return Policies. • Inspect the replaced parts to verify the FSA repair was completed. • If the FSA repair is found to be complete, the designated employee signs the repair order line or parts return stamp area (electronic or hand signed) for the FSA repair indicating the parts were inspected and validated to have been replaced. • After the parts have been inspected, they should be handled based on the guidance in the parts status report in the Online Warranty System (Hold, Return, CORE, Scrap, etc.). Copyright 2022 Ford Motor Company ATTACHMENT II Page 3 of 3 Recommended Delivery Hold Component Installation Program 22G05 Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit REPLACED FSA PARTS INSPECTION AND SIGN OFF (continued) This process is subject to review during warranty audits for FSA repairs with a repair order open date of March 1st 2021 or later. Any eligible FSA claims requiring parts replacement, found not to have been inspected and signed off during a warranty audit will be subject to chargeback and consideration for enrollment into the Dealer Incomplete Recall Repair Process. Note: Other approvals (electronic or handwritten) for add-on repair lines, dealer owned vehicle repairs, and repeat repairs do not qualify as FSA parts inspection approvals. The post repair FSA parts inspection process (electronic or handwritten) is independent from other warranty approval requirements. The approval by the designated employee implies that the FSA parts were found to be replaced and must be able to be clearly identified on the Repair Order. If multiple FSA’s require approval on a single Repair Order, each applicable occurrence will require individual post repair approval by the designated employee. • Copyright 2022 Ford Motor Company ATTACHMENT III PAGE 1 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 CERTAIN 2022 MODEL YEAR F-150 AND SUPER DUTY VEHICLES – EXTERIOR BADGE RETROFIT SERVICE PROCEDURE F-150 VEHICLES Table Of Contents Front Fender Vent Badges Left Hand/Right Hand (LH/RH).............................2 Front LH Door Badge.........................................................................................3 Front RH Door Badge.........................................................................................4 PowerBoost............................................................................................3 PowerBoost............................................................................................4 Tailgate Badge....................................................................................................5 EcoBoost................................................................................................5 King Ranch.............................................................................................6 Texas Edition..........................................................................................7 Oklahoma Edition..................................................................................8 Tremor.....................................................................................................9 Raptor.....................................................................................................10 NOTE: Ford Oval badges are not included in this program and should be considered a mis-build if missing. IMPORTANT: Badges must be installed when ambient temperatures and surface temperatures of vehicle and badge are confirmed to be between 60°F (16°C) and 100°F (38°C). Materials List Ruler/Scale (12"/30cm minimum) Clean Cloths Masking Tape Isopropyl Alcohol Plastic Trim Tool MOBILE SERVICE INSTRUCTIONS NOTE: If you suspect that you will not have Internet access at the vehicle's mobile service location then, you should print a copy of these instructions (including any required Workshop Manual references) for reference during the mobile service. CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 ATTACHMENT III PAGE 2 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Front Fender Vent Door Badges (LH/RH) NOTE: RH and LH front fender vent door badges are expected to be updated in pairs. If a normal production level badge is present, do not replace it (it should match the new part though). 1. Using a plastic trim tool, remove the LH side temporary front fender door badge. See Figure 1. NOTE: RH side shown, LH side similar. ONLY REPLACE TEMPORARY FRONT FENDER VENT DOOR BADGES 22624F FIGURE 1 2. Using isopropyl alcohol and a clean cloth, wipe the area where the new badge is to be installed. 3. Using another clean cloth, dry the area that was cleaned. 4. Allow the isopropyl alcohol one minute to fully evaporate. 5. Remove the tape liner from the back of the new badge 6. Install the new badge by aligning the clips on the back with the holes in the sheet metal and pressing in until they click. 7. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. 8. Repeat steps 1-7 for the RH side of the vehicle. STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 PLACE COPY HERE ATTACHMENT III PAGE 3 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Front LH Door Badge - PowerBoost 9. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 10. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 11. Using another clean cloth, dry the area that was cleaned. 12. Allow the isopropyl alcohol one minute to fully evaporate. 13. Measure and apply locating masking tape to the front LH door outer panel. See Figure 2. 22624C FIGURE 2 14. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 3. 15. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. See Figure 3. STUD FOR MISSING NUT STUD FOR 22624D MISSING NUT FIGURE 3 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 4 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Front RH Door Badge - PowerBoost 16. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 17. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 18. Using another clean cloth, dry the area that was cleaned. 19. Allow the isopropyl alcohol one minute to fully evaporate. 20. Measure and apply locating masking tape to the front RH door outer panel. See Figure 4. 22624A FIGURE 4 21. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 5. 22. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. See Figure 5. STUD FOR 22624B NUT MISSING FIGURE 5 STUD FOR MISSING NUT PLACE COPY HERE CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 5 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Tailgate Badge - EcoBoost 23. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 24. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 25. Using another clean cloth, dry the area that was cleaned. 26. Allow the isopropyl alcohol one minute to fully evaporate. 27. Measure and apply locating masking tape to the front tailgate outer panel. See Figure 6. 22624M FIGURE 6 28. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 7. 29. Using medium hand pressure, press for 3 seconds at a minimum of 3 separate locations along the length of the badge until the tape is fully adhered. See Figure 7. STUD FOR MISSING NUT 22624N FIGURE 7 STUD FOR MISSING NUT PLACE COPY HERE CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 6 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Tailgate Badge - King Ranch 30. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 31. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 32. Using another clean cloth, dry the area that was cleaned. 33. Allow the isopropyl alcohol one minute to fully evaporate. 34. Measure and apply locating masking tape to the tailgate outer panel. See Figure 8. 22624K FIGURE 8 35. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 9. 36. Using medium hand pressure, press for 3 seconds at a minimum of 2 separate locations along the length of the badge until the tape is fully adhered. See Figure 9. STUD FOR MISSING NUT 22624L FIGURE 9 STUD FOR MISSING NUT PLACE COPY HERE CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 7 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Tailgate Badge - Texas Edition 37. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 38. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 39. Using another clean cloth, dry the area that was cleaned. 40. Allow the isopropyl alcohol one minute to fully evaporate. 41. Measure and apply locating masking tape to the tailgate outer panel. See Figure 10. 22624G FIGURE 10 42. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 11. 43. Using medium hand pressure, press for 3 seconds at a minimum of 2 separate locations along the length of the badge until the tape is fully adhered. See Figure 11. STUD FOR MISSING NUT 22624H FIGURE 11 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 8 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Tailgate Badge - Oklahoma Edition 44. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 45. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 46. Using another clean cloth, dry the area that was cleaned. 47. Allow the isopropyl alcohol one minute to fully evaporate. 48. Measure and apply locating masking tape to the tailgate outer panel. See Figure 12. 22624I FIGURE 12 49. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 13. 50. Using medium hand pressure, press for 3 seconds at a minimum of 2 separate locations along the length of the badge until the tape is fully adhered. See Figure 13. STUD FOR MISSING NUT FIGURE 13 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 STUD22624J FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 9 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Tailgate Badge - Tremor 51. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 52. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 53. Using another clean cloth, dry the area that was cleaned. 54. Allow the isopropyl alcohol one minute to fully evaporate. 55. Measure and apply locating masking tape to the tailgate outer panel. See Figure 14. 22624Y FIGURE 14 56. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 15. 57. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. See Figure 15. STUD FOR MISSING NUT FIGURE 15 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 STUD22624Z FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT III PAGE 10 OF 10 COMPONENT INSTALLATION PROGRAM 22G05 Tailgate Badge - Raptor 58. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 59. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 60. Using another clean cloth, dry the area that was cleaned. 61. Allow the isopropyl alcohol one minute to fully evaporate. 62. Measure and apply locating masking tape to the tailgate outer panel. See Figure 16. 22624AA FIGURE 16 63. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 17. 64. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. See Figure 17. STUD FOR MISSING NUT FIGURE 17 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 STUD FOR 22624AB MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT IV PAGE 1 OF 7 COMPONENT INSTALLATION PROGRAM 22G05 CERTAIN 2022 MODEL YEAR F-150 AND SUPER DUTY VEHICLES – EXTERIOR BADGE RETROFIT SERVICE PROCEDURE SUPER DUTY VEHICLES Table Of Contents Front Fender Vent Badges Left Hand/Right Hand (LH/RH).............................2 Front LH Door Badge.........................................................................................3 Power Stroke..........................................................................................3 6.7L..........................................................................................................4 Front RH Door Badge.........................................................................................5 Power Stroke..........................................................................................5 6.7L..........................................................................................................6 Tailgate Badge....................................................................................................7 King Ranch.............................................................................................7 NOTE: Ford Oval badges are not included in this program and should be considered a mis-build if missing. IMPORTANT: Badges must be installed when ambient temperatures and surface temperatures of vehicle and badge are confirmed to be between 60°F (16°C) and 100°F (38°C). Materials List Ruler/Scale (12"/30cm minimum) Clean Cloths Masking Tape Isopropyl Alcohol Plastic Trim Tool MOBILE SERVICE INSTRUCTIONS NOTE: If you suspect that you will not have Internet access at the vehicle's mobile service location then, you should print a copy of these instructions (including any required Workshop Manual references) for reference during the mobile service. CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 ATTACHMENT IV PAGE 2 OF 7 COMPONENT INSTALLATION PROGRAM 22G05 Front Fender Vent Door Badges (LH/RH) NOTE: RH and LH front fender vent door badges are expected to be updated in pairs. If a normal production level badge is present, do not replace it (it should match the new part though). 1. Using a plastic trim tool, remove the LH side temporary front fender door badge. See Figure 1. NOTE: RH side shown, LH side similar. ONLY REPLACE TEMPORARY FRONT FENDER VENT DOOR BADGES 22624E FIGURE 1 2. Using isopropyl alcohol and a clean cloth, wipe the area that the new badge is to be installed at. 3. Using another clean cloth, dry the area that was cleaned. 4. Allow the isopropyl alcohol one minute to fully evaporate. 5. Remove the tape liner from the back of the new badge 6. Install the new badge by aligning the clips on the back with the holes in the sheet metal and pressing in until they click. 7. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. 8. Repeat steps 1-7 for the RH side of the vehicle. STUD FOR MISSING NUT STUD FOR MISSING NUT PLACE COPY HERE CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 PLACE COPY HERE PLACE COPY HERE ATTACHMENT IV PAGE 3 OF 7 COMPONENT INSTALLATION PROGRAM 22G05 Front LH Door Badge - Power Stroke 9. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 10. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 11. Using another clean cloth, dry the area that was cleaned. 12. Allow the isopropyl alcohol one minute to fully evaporate. 13. Measure and apply locating masking tape to the front LH door outer panel. See Figure 2. 22624O FIGURE 2 14. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 3. 15. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. See Figure 3. STUD FOR MISSING NUT FIGURE 3 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 STUD22624P FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT IV PAGE 4 OF 7 COMPONENT INSTALLATION PROGRAM 22G05 Front LH Door Badge - 6.7L 16. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 17. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 18. Using another clean cloth, dry the area that was cleaned. 19. Allow the isopropyl alcohol one minute to fully evaporate. 20. Measure and apply locating masking tape to the front RH door outer panel. See Figure 4. 22624Q FIGURE 4 21. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 5. 22. Using medium hand pressure, press for 3 seconds at a minimum of 2 separate locations along the length of the badge until the tape is fully adhered. See Figure 5. STUD FOR MISSING NUT FIGURE 5 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 STUD22624R FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT IV PAGE 5 OF 7 COMPONENT INSTALLATION PROGRAM 22G05 Front RH Door Badge - Power Stroke 23. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (16°C) and 100°F (38°C). 24. Using isopropyl alcohol and a clean cloth, wipe the area where the badge is to be installed. 25. Using another clean cloth, dry the area that was cleaned. 26. Allow the isopropyl alcohol one minute to fully evaporate. 27. Measure and apply locating masking tape to the front tailgate outer panel. See Figure 6. 22624S FIGURE 6 28. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 7. 29. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. See Figure 7. STUD FOR MISSING NUT FIGURE 7 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 STUD22624T FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT IV PAGE 6 OF 7 COMPONENT INSTALLATION PROGRAM 22G05 Front RH Door Badge - 6.7L 30. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (15.5°C) and 100°F (37.7°C). 31. Using isopropyl alcohol and a clean cloth, wipe the area that the badge is to be installed at. 32. Using another clean cloth, dry the area that was cleaned. 33. Allow the isopropyl alcohol one minute to fully evaporate. 34. Measure and apply locating masking tape to the front RH door outer panel. See Figure 8. 22624U FIGURE 8 35. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 9. 36. Using medium hand pressure, press for 3 seconds at a minimum of 2 separate locations along the length of the badge until the tape is fully adhered. See Figure 9. STUD FOR MISSING NUT 22624V FIGURE 9 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 STUD FOR MISSING NUT PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE ATTACHMENT IV PAGE 7 OF 7 COMPONENT INSTALLATION PROGRAM 22G05 Tailgate Badge - King Ranch 37. Confirm that the ambient temperature and surface temperature of both the vehicle and badge are between 60°F (15.5°C) and 100°F (37.7°C). 38. Using isopropyl alcohol and a clean cloth, wipe the area that the badge is to be installed at. 39. Using another clean cloth, dry the area that was cleaned. 40. Allow the isopropyl alcohol one minute to fully evaporate. 41. Measure and apply locating masking tape to the tailgate outer panel. See Figure 10. 22624W FIGURE 10 42. Remove the tape liner from the back of the badge and install to the door using the locating tape to properly align the badge. See Figure 11. 43. Using medium hand pressure, press for 3 seconds at a minimum of 4 separate locations along the length of the badge until the tape is fully adhered. See Figure 11. STUD FOR MISSING NUT STUD FOR MISSING NUT 22624X FIGURE 11 CPR © 2022 FORD MOTOR COMPANY DEARBORN, MICHIGAN 48121 10/2022 PLACE COPY HERE PLACE COPY HERE PLACE COPY HERE