SSM71910
Service Bulletin Details
Public Details for: SSM71910
Comprehensive component monitor-
- 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 - 2008 - 2007 - 2006 - 2005 - 2004 - 2003 - 2002 - 2001 - 2000 - 1999 - 1998 - 1997 -
Models from 2017
| 2017 JAGUAR XK |
Models from 2016
| 2016 JAGUAR XK |
Models from 2015
| 2015 JAGUAR XK |
Models from 2014
| 2014 JAGUAR XK |
Models from 2013
| 2013 JAGUAR XK |
Models from 2012
| 2012 JAGUAR XK |
Models from 2011
| 2011 JAGUAR XK |
Models from 2010
| 2010 JAGUAR XK |
Models from 2009
| 2009 JAGUAR XK |
Models from 2008
| 2008 JAGUAR XK |
Models from 2007
| 2007 JAGUAR XK |
Models from 2006
| 2006 JAGUAR XK |
Models from 2005
| 2005 JAGUAR XK |
Models from 2004
| 2004 JAGUAR XK |
Models from 2003
| 2003 JAGUAR XK |
Models from 2002
| 2002 JAGUAR XK |
Models from 2001
| 2001 JAGUAR XK |
Models from 2000
| 2000 JAGUAR XK |
Models from 1999
| 1999 JAGUAR XK |
Models from 1998
| 1998 JAGUAR XK |
Models from 1997
| 1997 JAGUAR XK |
TOPIx - SSM71910 - Comprehensive Component Monitor- XK (X100) ONLY. Reference SSM71910 Models XK / X100 Title Comprehensive Component Monitor- XK (X100) ONLY. Category Driveability Last modified 29-Jul-2014 00:00:00 Symptom 623000 Emissions Compliance Attachments DSG_03-06MY_X100_Pedal_Sensors.xml, Drive Cycles.pdf Content Issue: Page 1 of 1 2003-2006 XK (X100) Vehicles may fail the state inspection in some states which require the completion of the comprehensive component monitor, such as in New Jersey. Cause: The Accelerator Pedal Demand Position Sensor voltage is out of range, at 0% pedal angle. The voltage for pedal demand position sensor 1 should be between 0.88V and 0.99V. The voltages for pedal demand position sensor 2 should be between 3.89V and 4.18V. If the voltage for either sensor is not within the specified range at 0% pedal angle, it will inhibit the comprehensive component monitor from running. Solution: 1.Carry out an initial check on both the reference voltage and ground wiring to the Pedal Demand Sensor. 2. If no fault found, continue to investigate accelerator pedal sensor. Check the pedal demand position sensor voltages using IDS/SDD with ignition on. Refer to SSM 54457 - New Datalogger Signal Grouping Feature to assist in installing the attached xml file which will assist you in monitoring these two signals. 3. At 0% pedal angle, the voltage for pedal demand position sensor 1 should be between 0.88V and 0.99V. The voltages for pedal demand position sensor 2 should be between 3.89V and 4.18V. If either sensor voltage reading is outside of these ranges, replace entire pedal demand position sensor(s) assembly. Follow the Removal and Installation procedure found in TOPIx if replacement is required. Jaguar Special Tool 310-101 accelerator cable adjustment tool is required to successfully complete this repair. 4. After fitting a new Pedal Demand Sensor, conduct the following: with the engine running, depress accelerator pedal, raising pedal demand position sensor 1 voltage above 1.9V. Release pedal and idle for 10 seconds. Repeat until comprehensive component monitor sets to complete. If required, perform the attached drive cycles in order to get all other remaining monitors to set. http://topix.jaguar.jlrint.com/topix/service/archive/491432/index 8/5/2014