NTB23-002
Service Bulletin Details
Public Details for: NTB23-002
Models from 2022
2022 NISSAN ROGUE |
Models from 2021
2021 NISSAN ROGUE |
Classification: EC22-011 Reference: Date: NTB23-002 January 6, 2023 MIL ON WITH DTC P062F-00 STORED IN THE ECM APPLIED VEHICLES: APPLIED ENGINES: 2021-2022 Rogue (T33) PR25DD IF YOU CONFIRM The MIL is ON with DTC P062F-00 (Internal Control Module EEPROM Error) stored in the ECM. ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/3 SERVICE PROCEDURE 1. Using CONSULT-III plus, confirm the current ECM part number and write it on the repair order. If it matches one of the part numbers in Table 1, continue to step 2 on page 3. If it does not match one of the part numbers in Table 1, this bulletin does not apply. Go back to ASIST for further diagnostic and repair information. Table 1 MODEL CURRENT ECM PART NUMBER: 23761- 2021-2022 Rogue 6RA2D, 6RA2E, 6RA6B, 6RA6C, 6RA6D, 6RA7C, 6RA7D, 6RA7E, 6RA8C, 6RA8D, 6RA8E, 6RA9C, 6RA9D, 6RA9E, 6RG8A, 6RG8B, 6RG9A, 6RG9B, 6RR0E, 6RR1C, 6RR1D, 6RR1E, 6RR3E, 6RR4C, 6RR4D, 6RR4E, 6RR6B, 6RR6C, 6RR6D, 6RR6E, 6RR7A, 6RR7B, 6RR7C, 6RR7D, 6RR7E, 6RR8A, 6RR8B, 6RR8C, 6RR8D, 6RR8E, 6RR9B, 6RR9C, 6RR9D, 6RR9E, 6RW0B, 6RW0C, 6RW0D, 6RW0E, 6RW1B, 6RW1C, 6RW1D, 6RW1E, 6RW2B, 6RW2C, 6RW2D, 6RW2E, 6RW3B, 6RW3C, 6RW3D, 6RW3E, 6RW6A, 6RW6B, 6RW7A, 6RW7B, 6RW8A, 6RW8B, 6RW9A, 6RW9B Perform the following before starting the reprogramming procedure to prevent damage to the control unit. Connect the AC Adapter to the CONSULT PC. Connect the CONSULT PC to the Internet via Wi-Fi or a network cable. Ensure ASIST on the CONSULT PC has been synchronized (updated) to the current date and all CONSULT software updates (if any) have been installed. Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI. If Bluetooth® signal waves are within range of the CONSULT PC or VI during reprogramming, the reprogramming may be interrupted. Turn the hazard warning lamps ON. o Turn OFF all other vehicle electrical loads such as exterior lights, interior lights, HVAC, blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc. If electrical loads remain ON, the ECM may be damaged. Connect a battery maintainer or smart charger, set to reflash mode or a similar setting, to ensure the battery voltage stays between 12.0 V and 15.5 V. HINT: Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learning conditions: o Engine coolant temperature: 70 - 100°C (158 - 212°F) o Battery voltage: More than 12.9 V (At idle) o Transmission: Warmed up When reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learning, Accelerator Closed Position, and DTC Erase. 2/3 NTB23-002 2. Reprogram the ECM. HINT: If you are not familiar with the reprogramming procedure, click here. This will link you to the "CONSULT REPROGRAMMING FOR ENGINE OR TRANSMISSION CONTROL MODULE (ECM OR TCM)" general procedure. 3. After completing Erase All DTCs, print a copy of the CONSULT screen showing the before and after part numbers of the control unit and attach it to the repair order. CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: (1) (2) DESCRIPTION PFP OP CODE SYM DIA FRT Reprogram ECM (1) DE97AA ZE 32 (2) Reference the electronic parts catalog and use the ECM (23703-*****) as the Primary Failed Part (PFP). Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat Rate Time (FRT). AMENDMENT HISTORY PUBLISHED DATE REFERENCE January 6, 2023 NTB23-002 DESCRIPTION Original bulletin published 3/3 NTB23-002