22-NA-200

Bulletin No.:
Service Bulletin
Date:
22-NA-200
February, 2023
TECHNICAL
Subject:
Brand:
Cadillac
Child Safety Lock Update
Model:
CT4
CT5
Model Year:
VIN:
from
to
from
to
2020
2022
—
—
Engine:
Transmission:
—
—
Involved Region or Country
United States, Canada, China
Condition
Some customers may comment on a message reading "UPDATE UNSUCCESSFUL.”
The over-the-air update was released to correct a concern with the Child Lock not
working properly.
Cause
The cause of the condition may be a Body Control Module (BCM) software update that
failed to complete.
Correction
The updated software is currently available in the Service Programming System (SPS)
database. Reprogram the BCM with the current calibrations to resolve this concern.
Service Procedure
Important: Service agents must comply with all
International, Federal, State, Provincial, and/or
Local laws applicable to the activities it performs
under this bulletin, including but not limited to
handling, deploying, preparing, classifying,
packaging, marking, labeling, and shipping
dangerous goods. In the event of a conflict between
the procedures set forth in this bulletin and the
laws that apply to your dealership, you must follow
those applicable laws.
• Ensure the programming tool is equipped with the
latest software and is securely connected to the
data link connector. If there is an interruption
during programming, programming failure or
control module damage may occur.
• Stable battery voltage is critical during
programming. Any fluctuation, spiking, over
voltage or loss of voltage will interrupt
programming. Install a GM Authorized
Programming Support Tool to maintain system
voltage. Refer to www.gmdesolutions.com for
further information. If not available, connect a fully
charged 12V jumper or booster pack disconnected
from the AC voltage supply. DO NOT connect a
battery charger.
• Follow the on-screen prompts regarding ignition
power mode, but ensure that anything that drains
excessive power (exterior lights, HVAC blower
motor, etc) is off.
Copyright 2023 General Motors LLC. All Rights Reserved.
•
Clear DTCs after programming is complete.
Clearing powertrain DTCs will set the Inspection/
Maintenance (I/M) system status indicators to NO.
Important: The service technician always needs to
verify that the VIN displayed in the TLC left side drop
down menu and the top center window match the VIN
plate of the vehicle to be programmed prior to using
Service Programming System 2 (SPS2) for
programming or reprogramming a module.
• For the TLC application, service technicians need
to always ensure that the power mode (ignition) is
“ON” before reading the VIN from the vehicle’s
VIN master module and that they do not select a
VIN that is already in the TLC application memory
from a previous vehicle.
• If the VIN that shows up in the TLC top center
window after correctly reading the VIN from the
vehicle does not match the VIN plate of the
vehicle, manually type in the VIN characters from
the vehicle VIN plate into the TLC top center
window and use these for programming or
reprogramming the subject module with the
correct vehicle VIN and software and/or
calibrations.
• The Engine Control Module (ECM) is the master
module (for VIP vehicles) that TLC reads to
determine the VIN of the vehicle. If the VIN read
from the vehicle by TLC does not match the VIN
plate of the vehicle, the ECM also needs to be
reprogrammed with the correct VIN, software and
calibrations that match the vehicle’s VIN plate.
Page 2
February, 2023
Bulletin No.: 22-NA-200
•
The Body Control Module (BCM) is the master
module (for GEM vehicles) that TLC reads to
determine the VIN of the vehicle. If the VIN read
from the vehicle by TLC does not match the VIN
plate of the vehicle, the BCM also needs to be
reprogrammed with the correct VIN, software and
calibrations that match the vehicle’s VIN plate.
Caution: Be sure the VIN selected in the drop down
menu (1) is the same as the vehicle connected (2)
before beginning programming.
5743643
Important: If the vehicle VIN DOES NOT match, the
message below will be shown.
5877000
Bulletin No.: 22-NA-200
February, 2023
Page 3
5644477
Important: Techline Connect screen shown above.
Important: If the same calibration/software warning is
noted on the TLC or SPS Summary screen, select OK
and follow screen instructions. After a successful
programming event, the WCC is located in the Service
Programming System dialogue box of the SPS
Summary screen. Document the WCC on the job card.
No further action is required. Refer to the Warranty
Information section of this bulletin.
1. Reprogram the Body Control Module. Refer to K9
Body Control Module: Programming and Setup in
the Service Manual.
Page 4
February, 2023
Bulletin No.: 22-NA-200
5644478
Note: The screenshot above is an example of module
programming and may not be indicative of the specific
module that is being programmed. Module selection
and VIN information have been blacked out.
Important: To avoid warranty transaction rejections,
you MUST record the warranty claim code provided on
the Warranty Claim Code (WCC) screen shown above
on the job card. Refer to callout 1 above for the location
of the WCC on the screen.
2. Record the Warranty Claim Code on the job card
for warranty transaction submission.
Warranty Information
For vehicles repaired under warranty, use:
Labor
Operation
Description
Labor Time
Use
Published
Body Control Module
Labor
2810215*
Reprogramming with SPS
Operation
Time
Important: *To avoid warranty transaction rejections,
carefully read and follow the instructions below:
• The Warranty Claim Code must be accurately entered
in the “SPS Warranty Claim Code” field of the
transaction.
• When more than one Warranty Claim Code is
generated for a programming event, it is required to
document all Warranty Claim Codes in the “Correction”
field on the job card. Dealers must also enter one of the
codes in the “SPS Warranty Claim Code” field of the
transaction, otherwise the transaction will reject. It is
best practice to enter the FINAL code provided by
SPS/SPS2.
Bulletin No.: 22-NA-200
February, 2023
Page 5
Warranty Claim Code Information Retrieval
6125774
If the Warranty Claim Code was not recorded on the
Job Card, the code can be retrieved in the SPS2
system as follows:
1. Open TLC on the computer used to program the
vehicle.
2. Select and start SPS2.
3. Select Settings (1).
4. Select the Warranty Claim Code tab (2).
The VIN, Warranty Claim Code and Date/Time will be
listed on a roster of recent programming events. If the
code is retrievable, dealers should resubmit the
transaction making sure to include the code in the SPS
Warranty Claim Code field.
Version
2
Modified
Released October 10, 2022
Revised February 02, 2023 – Added the 2020 Model Year.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these
technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper
service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a
job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your
vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the
information.
WE SUPPORT VOLUNTARY
TECHNICIAN
CERTIFICATION