No. 209-22
Service Bulletin Details
Public Details for: No. 209-22
Technical information on wnq3 a?? Checking windshield and re-bonding if necessary
- 2021 -
Models from 2021
2021 PORSCHE MACAN |
Service Technical Information 209/22 ENU WNQ3 6 WNQ3 – Checking Windshield and Re-Bonding if Necessary (Workshop Campaign) Vehicle Type: Macan (95B) Model Year: 2021 Concerns: Windshield Cause: On the affected vehicles, there is a possibility that the windshield was not installed according to the specifications during production. Due to a potentially insufficient hardening of adhesive, a gap can occur between the windshield seal and the roof due to slight slipping. As a result, wind noise can be perceived by the customer from a driving speed of approx. 60 km/h (37 mph). Action required: Check windshield and re-bond it depending on the inspection result. Affected Vehicles: Only vehicles assigned to the campaign (see also PCSS Vehicle Information). Required parts and materials Information No parts are required for inspection. Required parts: Part No. Designation – Point of use Quantity 00004330535 Adhesive set, commercially available: - Teroson - Makra - 3M 1 piece* 9A795560900 Adhesive film – Rain sensor 1 piece *If necessary, the adhesive set can be ordered using the specified Porsche part number or from your consumables supplier. When purchasing the adhesive set from your consumables supplier, enter Part No. WNQ10000001, designation “adhesive” as an additional part costing $ 118.65 during warranty invoicing. AfterSales Feb 9, 2023 Page 1 of 4 6 Service Required materials: Technical Information ENU 209/22 WNQ3 Part No. Designation – Point of use ... Cutting wire for loosening glass panes, corresponds to 1 piece* (for warranty invoicing part number 00004330332 only) commercially available: Würth Quantity * If necessary, the cutting wire can be obtained using the Porsche part number provided or through your consumables supplier. In the last case, enter Part no. WNQ30000002, designation “cutting wire” as external item & additional measures costing $ 2.10 during warranty invoicing. Required tools Information No tools are required to inspect the windshield. Required tools: • • • • VAG 1474B - Windshield cutting tool or VAS 861001A - Cutting thread VAS 6427 - Release pliers VAS 6935 - Pole terminal puller 9768 - 9768 - Electronic torque wrench, 2 - 100 Nm (1.5 - 74 ftlb.) Checking windshield Work Procedure: 1 Check for gaps between windshield and seal. Information The seal must always contact the roof over the entire area. Please note that even a small gap can cause wind noise. Feb 9, 2023 Page 2 of 4 AfterSales Service Technical Information 209/22 ENU WNQ3 6 Checking windshield Assessment ( ) There is no windshield gap. Action – End of action – Continue with Step 3. [Scope 1] (✗) There is a windshield gap. Continue with Step 2. [Scope 2] 2 Remove and re-bond windshield. Workshop Manual '641219 Removing and installing windscreen' 3 Enter the campaign in the Warranty and Maintenance booklet. Warranty processing Information The indicated labor times were determined specifically for this campaign and may differ from the labor times published in the Labor Operation List in the PCSS. AfterSales Feb 9, 2023 Page 3 of 4 6 Service WNQ3 Scope 1: Technical Information ENU 209/22 Checking windshield Labor time: Labor time: 16 TU Checking windshield Damage code WNQ3 066 000 1 Scope 2: Checking and re-bonding windshield Labor time: Checking and re-bonding windshield Includes: Removing and installing interior rearview mirror Removing and installing rain sensor Removing and installing mobile communication antenna Removing and installing cowl panel cover Removing and installing left and right A-pillar trim panels. Loosening and securing front headliner Removing and installing windshield trim strip Labor time: 416 TU Required parts: WNQ30000001 Adhesive set 1 piece (for warranty invoicing only)* 9A795560900 Adhesive film 1 piece WNQ30000002 Cutting wire 1 piece (for warranty invoicing only)** * For warranty invoicing, invoice the Part No. WNQ30000001, “adhesive” designation, as an additional part. Cost: $ 118.65. ** For warranty invoicing for Part No. WNQ30000002, enter “expendable items” designation as sublet item & additional measures. Amount $ 2.10. Damage code WNQ3 066 000 1 Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed. © 2023 Porsche Cars North America, Inc. Feb 9, 2023 Page 4 of 4 AfterSales