WNT1

WNT1 Workshop campaign - Reprogramming
Connect control unit and the central computer
(PCM) (Cluster 37)
Update 2/13/23
Please note that there may be a failure of the integration test during the performing of this campaign.
This concern is currently under review by PAG and we will provide further updates when available.
WNT1 Workshop campaign - Reprogramming Connect
control unit and the central computer (PCM) (Cluster 37)
ID Number
WNT1
Models
Cayenne (9YA/9YB)
Models Years
2022
VIN List
Attached
Number of Affected VINs
9,960
Issue Description
Optimized software is available for the central computer (PCM) control unit and Connect control unit.
The software for the Connect control unit and the central computer (PCM) control unit must therefore be
updated on the affected vehicles and the Driver's Manual must be replaced with an updated status.
What Dealers Should do
Please arrange for this measure to be carried out as
soon as possible on affected vehicles. As of the time
of this posting, the repair is immediately available.
TI Number
No. 236-22
Important information on handling the integration test on
the PIWIS Tester as part of a workshop campaign
1
WNT1 Workshop campaign - Reprogramming Connect control unit and the central computer (PCM) (Cluster
37)
The integration test on the PIWIS Tester checks the conformity of the control unit system of vehicles on the
basis of the approved customer service installation specification (Service Installation Instructions). This will
detect an unapproved or no longer up-to-date control unit system.
When new control unit software is provided, the Service Installation Instructions are also amended. This will
take effect immediately with the related PIWIS Tester release. As a result, all relevant vehicles are tested
against the currently approved software system after the PIWIS Tester release has been installed. Depending
on the result of the check, all relevant control units must be updated when prompted to do so by the PIWIS
Tester.
Following this workshop campaign, all control units to be programmed as per the integration test in the PIWIS
Tester will be displayed as "red" when the relevant PIWIS Tester release is published and must therefore be
updated.
Required parts
The campaign must not be carried out without replacing the Driver's Manual.
Scope 2 (Cayenne):
Part number
WKD9Y002B2122*
Designation
Driver's Manual
Quantity/vehicle
1 piece
Parts return*
No
*For warranty invoicing, enter the Part No. WNT10000001 with the designation "Owner's Manual" as
accessories costing $0.01. If you incur shipping costs when ordering the Owner's Manual, please invoice these
costs under the Part No. WNT10000002, with the designation "Shipping costs" as an additional part. Maximum
cost $5.25. Please document a copy of the invoice for this in the warranty claim.
Required tools
Designation
Part No./Specification/Special instructions
Battery charger
Battery charger with a current rating of at least 90 A
and - if required - also with a current and voltage-controlled charge map for lithium starter batteries.
PIWIS Tester 3
-
Blank USB storage medium Type A+C 32 GB (for
PCM update)
V04014999WW000
Blank USB storage medium, Type C (for onboard
Driver's Manual update**)
e.g. V04014999WW000
* The PCM control unit software update is performed using a USB storage
medium. The software version that is specific to each region must be
downloaded using the software tool PiUS (Porsche integrated Update Service)
and must be installed on a blank USB storage medium.
2
WNT1 Workshop campaign - Reprogramming Connect control unit and the central computer (PCM) (Cluster
37)
Pay particular attention to the following:
• For this PCM software update, the USB storage medium USB Type A+C 32 GB with the part number
V04014999WW000 must be used.
• To use the software tool, one blank or re-writable USB storage medium is required for each individual
software.
• The software available in PiUS must only be used in accordance with the instructions provided in a
Technical Information published for this purpose.
Overview of PiUS software versions
Scope 1-6:
Part No.*
Designation
Vehicle allocation
- Region
9Y2909000F
PCM software update
- North America
- Mexico
I-No. ER3 / ER4+KD0
Blank USB storage medium for Driver's Manual update:
A blank USB storage medium is required for installing the onboard Driver's Manual (approx. 100 MB). If there is
already data stored on the USB storage medium, this will be deleted during the procedure.
Required software
PIWIS Tester 3/4 test software version
41.700.010 (or higher) Cayenne only
Customer mobility
If requested, mobility for the affected customer can be guaranteed by offering a suitable replacement vehicle.
Please invoice this additional service via WWS with the campaign scope.
Further Information
Validity:
This workshop campaign will be carried out up to February 3rd, 2028 and will be closed on that date.
Please note that warranty claims can only be processed before this date.
Attachments
1. VIN_List_Report_WNT1_2023-02-03_V2.xlsx
2. WNT1_Checklist.pdf
3