15-305-22R
Service Bulletin Details
Public Details for: 15-305-22R
The following information announces reprogramming file availability and provides a software update installation procedure to optimize the new gen 4.5 denso cp1.5 audio and navigation head units utilized in the models listed.
- 2023 -
Models from 2023
2023 SUBARU ASCENT |
2023 SUBARU LEGACY |
2023 SUBARU OUTBACK |
ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q IMPORTANT - All Service Personnel Should Read and Initial in the boxes provided, right. SERVICE MANAGER q © 2022 Subaru of America, Inc. All rights reserved. SERVICE BULLETIN APPLICABILITY: 23MY Outback/Legacy Models (including Wilderness models) 23MY Ascent Models SUBJECT: NUMBER: 15-305-22R DATE: 11/15/22 REVISED: 03/09/23 Reprogramming File Availability for Optimization of Gen 4.5 Denso CP1.5 Infotainment Systems INTRODUCTION: The following information announces reprogramming file availability and provides a software update installation procedure to optimize the new Gen 4.5 Denso CP1.5 Audio and Navigation head units utilized in the models listed above. As in previous models, the procedure will involve either downloading the software update files from Subarunet or using those sent directly from Nuspire to the SDS Notebook and transferring them onto a USB flash drive for head unit installation. It is VERY IMPORTANT to read and understand this information completely before proceeding. CAUTION: VEHICLE SERVICE PERFORMED BY UNTRAINED PERSONAL COULD RESULT IN THE EQUIPMENT DAMAGE OR EVEN SERIOUS INJURY. Service Bulletin is intended for use by trained technicians ONLY. It informs technicians of conditions, which may occur in some vehicles or provides information, which could assist with proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. A timeline chart along with a complete list of all the conditions addressed and enhancements included in this and previous Denso software updates are provided in “Appendix D” and “Appendix E” located at the end of this bulletin. IMPORTANT NOTE: The update contains 1 folder and 1 file. When performing an update, the USB must contain the matching number of folders and files and all files must be replaced. ALWAYS use the latest files together as a set. NEVER reuse or combine files from a prior update with a newer version. CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. Subaru of America, Inc. is ISO 14001 Compliant ISO 14001 is the international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 1 of 30 PART INFORMATION: NOTE: High Level unit is equipped with Navigation option (Map icon on Home screen) 11.6-Inch Display, Mid and High Level Units Dual 7.0-Inch Display, Base Level Unit Materials Required: An empty, USB 2.0 or 3.0 storage device (flash drive) will be needed to perform the update procedure. The device should be dedicated to storing and transferring these updating files only. It should be a minimum of 64GB or more in size and contain a NTFS file format before downloading the update files onto it. Be sure to locate and re-format any existing USB drives used for updating audio units. They must be fully cleared before adding these new update files to them. IMPORTANT NOTES: • NEVER change the update file names after downloading them. • NEVER save any other files on the same flash drive. There are various types of USB flash drive available from many suppliers. If the head unit does NOT recognize the USB drive during the reprogramming process due to Controller IC type of USB drive or Compatibility with the head unit, confirm the flash drive format is NTFS. The flash drive must be formatted for NTFS. If a recognition problem persists, use a USB flash drive from another manufacturer. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 2 of 30 • Kingston®: DataTraveler G3 Series DataTraveler 100 G3 DT100G3 DataTraveler SE9 Series DataTraveler SE9 G2 3.0 DTSE9G2 Digital Data Traveler 3.0 USB Flash Drive - Violet DTIG4 • SanDisk®: Ultra Series SDCZ48-064G-J57 Cruzer Blade Series Cruzer Glide Series CZ60 SDCZ60-064G-B35 • Transcend®: JetFlash 790 Series TS64GJF790KBE • PNY®: Retract USB 3.0 Flash Drive, black (P-FD64GTRTC-GE) • Silicon Power®: 2 Pack USB 3.0/3.1 Gen1 USB Flash Drive Blaze B02 IMPORTANT NOTE: The update contains 1 folder and 1 file. When performing an update, the USB must contain the matching number of folders and files and all files must be replaced. ALWAYS use the latest files together as a set. NEVER reuse or combine files from a prior update with a newer version. Bulletin Number: 15-305-22R; Revised: 03/09/23 Continued... Page 3 of 30 SERVICE PROCEDURE / INFORMATION: REMINDER: Customer satisfaction and retention starts with performing quality repairs. STEP 1- VERY IMPORTANT: Before proceeding with the software updating procedure, the currently installed software version ID MUST be confirmed by following the steps below: 1a) After starting the engine and system boot-up completes, from the HOME screen, touch the Settings button. 1b) Press the General button. Use the down arrow to scroll to System Information then press to display the System Information / Version information. The examples below identify the head unit model and the last 6 digits signify the software version number. Examples: • F61WHMxxx-xxx (High model software) • F61WMMxxx-xxx (Mid model software) • F61WBMxxx-xxx (Base model software) Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 4 of 30 MY 23MY Carline Outback/Legacy (including Wilderness models) 23MY Trim/Grade Older Software Versions Latest Software Versions BASE 013-280 023-580 033-680 MID 013-280 023-580 033-681 HIGH 013-280 023-580 033-681 MID 023-580 033-681 HIGH 023-580 033-681 Ascent If the software version number matches “Older Software Versions” proceed to STEP 2 below. If the software version is “Latest Software Version” as the unit already has the latest software version installed. STEP 2- Prepare the USB: CAUTION: Do not use any USB flash drive which utilizes file organizing software or an operating system. VERY IMPORTANT: Before attempting to download any data files, confirm the PC and flash drive being used is not infected with any virus. The flash drive MUST be formatted for NTFS. • Make sure the USB flash drive contains no other files. • Right click on the corresponding “Removable Disk”. • Select “Format”. • From the File System drop-down menu, select “NTFS” • Check the “Quick Format” box (if not already done). • Click on “Start” to format the USB flash drive. STEP 3- Download the Update Files to the USB: The files are available for download on Subarunet (see “A” below). The applicable reprogramming files have also been sent directly to retailers by Nuspire in the same way a Select Monitor Update would be pushed out. (see “B” below). Follow “A” when using files downloaded from Subarunet. Follow “B” when using the files sent directly to the SDS notebook from Nuspire. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 5 of 30 “A” When using update files downloaded from Subarunet: IMPORTANT: Files downloaded from Subarunet will be .zip files and must be unzipped before they can be used. Using the normal audio / navigation system file update download procedure: Go to Subarunet, select Service Operations and Technical>>Forms/Downloads>>Gen 4/Denso for Audio/ Navi then click on the applicable Hyperlink to download the file(s) to your SDS Notebook or PC: Updates for Gen 4.5 Denso Audio and Navigation Head Units - 2023MY Legacy/Outback and 2023MY Ascent: 23-Legacy-Outback-23-Ascent-Denso-CP1.5 AUDIO UPDATE- February 2023 • Go to Downloads. • CAUTION: After download is complete, NEVER change the file or folder names. • Open / display the contents of File folder, for example: “File name TBD”. • Click on “Extract All Files”. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 6 of 30 • The screen below will appear to set a destination for the extracted file. • Double-click on the required folder (for this example, used folder titled “Version7(RC2105)_ F11GHM072-582(High)”). Copy all files then paste (or click / drag) it to the “clean” USB flash drive as listed (Removable Disk) in the directory. IMPORTANT NOTE: The update contains 1 folder and 1 file. When performing an update, the USB must contain the matching number of folders and files and all files must be replaced. ALWAYS use the latest files together as a set. NEVER reuse or combine files from a prior update with a newer version. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 7 of 30 • To avoid confusion, use a permanent marker to label the flash drive with the file contents (e.g. Denso CP1.5 2023MY ALL). • Go to Step 4. “B” When using update files sent directly from Nuspire: • Go to My Documents on the GUI screen click on the folder “Denso CP1 Audio-Navi Update Files” to display the list of available update files shown below. IMPORTANT: Always confirm there is a correct folder. If not, the SDS notebook hasn’t been updated with the latest release. Please contact Nuspire to request they resend the update.” • CAUTION: After download is complete, NEVER change the file or folder names. • Double-click on the required folder (for this example, select the file entitled “2023”) and the update file will display as shown. Select all folders and files and either copy / paste or click / drag them to the USB flash drive. IMPORTANT NOTE: The update contains 1 folder and 1 file. When performing an update, the USB must contain the matching number of folders and files and all files must be replaced. ALWAYS use the latest files together as a set. NEVER reuse or combine files from a prior update with a newer version. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 8 of 30 • Once all files have been loaded onto the USB flash drive, right click on the drive and select “Eject”. CAUTION: NEVER change the file names. • Remove the USB flash drive after the prompt appears that says “Safe to Remove Hardware”. • Mark the USB to indicate the head unit it will update (Denso CP1.5 2023MY ALL in this example). • Proceed to STEP 4 below. STEP 4- Perform the software update. CAUTIONS: NEVER attempt to install the software immediately following an exchange module installation. Let the system restart first and operate for 20 minutes. NEVER attempt to install the software a second time for 30 minutes following a previously unsuccessful software installation. NEVER attempt to install the software for at least 30 minutes after completing a FOTA update. 4a) Perform the update in a well ventilated location if updating with the engine running OR with the ignition ON and a battery charger connected. 4b) PRESS and HOLD the RIGHT-side temperature control buttons (both up and down) and press the Tune / Scroll knob 6 times then release all to display the Dealership Mode Menu. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 9 of 30 4c) Select Software Update from the Dealership Mode menu. IMPORTANT NOTE: On a RARE occasion, the message “Software update setup is initializing…” may be displayed. Should this occur, proceed to “Appendix A” starting on pg. 16 of this bulletin for further instruction. 4d) The screen below will be displayed. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 10 of 30 4e) Insert reprogramming USB into the USB port and press OK. NOTE: If after plugging in the USB, the screen displays a Software Loading Unsuccessful message, confirm the USB device has been properly formatted and the software on the device matches the system being reprogrammed (example: Base software is being used to update a Base system) and retry. If you get the message Software Update Incomplete as shown below, please don’t replace the hardware but retry updating the software according to the instructions in “Appendix B ” on pg. 17. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 11 of 30 4f) The screen below will be displayed. Press OK to start the software update. NOTE: The actual software version displayed will be different from the picture shown below. Software Version Table Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 12 of 30 4g) Once the update begins, the screen below will be displayed with a progress bar. It takes about 15 to 20 minutes for the update to complete. VERY IMPORTANT: NEVER turn off the ignition while the software update is in process. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 13 of 30 4h) When the software update is complete, the following screen will be displayed (the actual software version will be different). IMPORTANT NOTE: On rare occasions a “Software Update Incomplete” message may appear in this step which occurs due to a bug in the software update procedure. Proceed to Step 4i below to confirm the software version has been updated to the latest version. 4i) Select OK in the screen above then remove the H/U reprogramming USB from the USB port. 4j) Turn the Ignition OFF, open the driver’s door then close the driver’s door. 4k) Wait for 3 minutes, then turn the ignition ON. 4l) Access Dealership Mode following steps provided item 4b and using the tables below, confirm the software update completed successfully. NOTE: The new Software Version number must be entered when prompted at claim entry. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 14 of 30 Software Version Table (Including Wilderness) 4m) Turn the ignition OFF, open the driver’s door then close the driver’s door to complete the procedure. WARRANTY / CLAIM INFORMATION: For vehicles within the Basic New Car Limited Warranty period or covered by an active Subaru Added Security Gold plan, this repair may be submitted using the following claim information: REMINDER: The new Software Version number must be entered when prompted at claim entry. NOTE: Retailers are now permitted to claim up to $5.00 per claim in Sublet to help offset the cost of replacement USB drives. Repeated re-formatting of the USB drives used for reprogramming can compromise their ability to operate properly. Over time, hardware connections can loosen and stored data files can become corrupted. Retailers are responsible for replacing any worn or otherwise inoperable USB drives as needed. This compensation is intended to help defray those costs. IMPORTANT REMINDERS: • SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time. • Always check for any open recalls or campaigns anytime a vehicle is in for servicing. • Always refer to STIS for the latest service information before performing any repairs. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 15 of 30 “APPENDIX A” Follow this procedure in the RARE case of “Software update setup is initializing…” message is displayed: • If the screen shown below appears, WAIT for approximately 30 minutes or as long as necessary (waiting for longer than 60 minutes might indicate system malfunction). In that case please perform recovery according to the instructions in “Appendix B ” to allow the Software update setup initialization process to complete. Base High/Mid • The screens shown below will be displayed when the process completes. Base High/Mid 1. Turn the ignition OFF, open the driver’s door, close the driver’s door and WAIT for 3 or more minutes before proceeding further. 2. Open the driver’s door again and either turn the ignition ON (if a charger is connected) or start the engine. 3. Go to Dealership Mode menu again (PRESS and HOLD the RIGHT-side temperature control buttons (both up and down) and press the Tune / Scroll knob 6 times then release all to display the Dealership Mode) and select Software Update as in STEP 4c beginning on pg. 10. IMPORTANT NOTE: If this procedure is required, contact Techline as additional action may be necessary. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 16 of 30 “APPENDIX B” In case of retrying the software update after the first attempt of update fails. • If the first attempt of update fails with the message below, follow the steps described below 1-2 to 1-8 before retrying the software update. 1-1. Select OK in the screen below High/Mid Base 1-2. Turn the ignition switch or the engine OFF, and turn it ON again. Caution: Do not remove battery terminal and keep battery power supply. Base High/Mid Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 17 of 30 1-3. Select Software Update in the Dealership Mode diagnostics screen. Base High/Mid 1-4. When you see the screen below, wait for approx. 15 minutes until the initialization is complete Base High/Mid Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 18 of 30 1-5. You will see the screen below when the initialization is complete. Base High/Mid 1-6. Turn the ignition switch or the engine OFF, open the driver side door and close the door then wait for 3 minutes. 1-7. Open the driver side door then turn the ignition switch or the engine ON. 1-8. Go to Dealership Mode menu again (PRESS and HOLD the RIGHT-side temperature control buttons (both up and down) and press the Tune / Scroll knob 6 times then release all to display the Dealership Mode) and select Software Update as in STEP 4c beginning on pg. 10. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 19 of 30 “APPENDIX C” In case the Gracenote update popup screen appears or software initializing screen does not go away for more than 20 minutes, please perform steps 2-1 to 2-11. High/Mid 2-1. Select “Settings” in the Dealership Mode diagnostics screen. High/Mid Base Base Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 20 of 30 2-2. Select “Memory Initialization” High/Mid 2-3. Select “OK” After Memory Initialization, all settings are reset to factory default. High/Mid Base Base Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 21 of 30 2-4. You will see the following screen High/Mid Base 2-5. After a few seconds, system restarts itself. 2-6. Select “Software Update” in the Dealership Mode diagnostics screen. Base High/Mid Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 22 of 30 2-7. When you see the screen below, wait for about 15 minutes until the initialization is complete Base High/Mid 2-8. You will see the screen below when the initialization is complete. High/Mid Base 2-9. Turn the ignition switch or engine OFF, open the driver side door and close the door then wait for 3 minutes. 2-10. Open the driver side door then turn the ignition swatch or engine ON. 2-11. Go to Dealership Mode menu again (PRESS and HOLD the RIGHT-side temperature control buttons (both up and down) and press the Tune / Scroll knob 6 times then release all to display the Dealership Mode) and select Software Update as in STEP 4c beginning on pg. 10. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 23 of 30 “APPENDIX D” Denso Gen 4.5 Software Update Timeline (TSB Number: 15-305-22) Update # MY Version Release Date: 0 2023 0 9/1/2022 F61WHM013-280 (High model software) F61WMM013-280 (Mid model software) F61WBM013-280 (Base model software) NEW Version ID #: SOP for 23MY Outback/Legacy 1 2023 RC1 11/11/2022 F61WHM023-580 (High model software) F61WMM023-580 (Mid model software) F61WBM023-580 (Base model software) - See “Conditions Addressed by Update #1” as outlined in “Appendix E” below 2 2023 RC2 2/24/2023 F61WHM033-681 (High model software) F61WMM033-681 (Mid model software) F61WBM033-680 (Base model software) Conditions Addressed: - See "Conditions Addressed by Update #1" as outlined in "Appendix E" below Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 24 of 30 “APPENDIX E” Symptoms Addressed By Update #2: Number Symptoms to be Improved: 1 CID goes black and does not accept any control. 2 CID reboots. 3 “Manage Devices” is grayed out and cannot establish Bluetooth connection. 4 When the Bluetooth connection is cancelled manually on the mobile phone side during hands-free calling, the Bluetooth connection is disabled for that particular mobile phone. Even when it occurs, the connection can be reestablished by deleting the device in “Manage Devices” and register the device again by adding operation. 5 Bluetooth connection fails against the device that was pared before and “Manage Devices” is grayed out. 6 Bluetooth connection is disabled with a discrepancy in the display of status bar (showing Bluetooth devices being connected) and the “Manage Devices” screen (showing no Bluetooth devices being connected.) 7 Android Auto Wireless (AAW) cannot be connected. 8 Android Auto Wireless (AAW) cannot be started from “Manage Devices” Screen. 9 Sound volume control does not work while using Android Auto. It is caused by data communication error between Android device and CCU. 10 Cyclic short noise like a drilling or vibration is heard from speakers. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 25 of 30 Number Symptoms to be Improved: 11 Sound is lost when changed to Subchannel 2 right after a preset HD radio channel has been selected. 12 After the destination is set on Navi screen, voice recognition command of “Findalong route” is made, search results are not given in order of distance. 13 When “Call” button is pressed in “Confirm Destination” screen of Navigation system (to call the destination site,) the call can be made but the screen does not transit to phone call screen. 14 Popup of “The update was successfully installed” is not displayed after reboot (IG-OFF and ON) operation of FOTA (Firmware Over The Air) update. 15 When tapping preset “Team Channel” on SMX, a popup of different game is displayed. It can occur under the following sequence of operations: 16 A wrong search location is used on TravelLink function. Example of the symptom. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 26 of 30 Number Symptoms to be Improved: 17 Music cannot be played sequentially when they are stored in different folders in a USB memory. The specifications are improved to enable music in different folders to be played sequentially. 18 "Repeat All” is added as one of the play modes. 19 “Track-up/down” can be used across folders in “Repeat All” mode. Symptoms Addressed By Update #1: Number 1 Symptoms to be Improved: iPod/iPhone tab in Media screen cannot be selected, when connected by USB. The symptom occurs when the iPhone is connected to CP1.5 via Bluetooth in parallel to USB connection by error. (It is supposed to be connected either via Bluetooth or by USB.) 2 On the “Manage Devices” screen Bluetooth cannot be selected as connection preference. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 27 of 30 Number 3 Symptoms to be Improved: Status of Bluetooth on Manage Device screen is displayed as disconnect even though the Bluetooth Icon on top right of the screen is showing active. 4 Cannot pair new Bluetooth device or cannot connect paired Bluetooth device. This symptom possibly occurs after repeating IG OFF/ON operation while still pairing operation. 5 Cannot pair Bluetooth device, when Bluetooth device has long name including symbols. 6 SXM station shortcut created by the customer does not work when the SXM has not been used as audio source after the Ignition Switch was turned on in the ignition cycle. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 28 of 30 Number Symptoms to be Improved: 7 Manage Device Screen becomes dark and inoperative when Ignition Switch is turned Off and On while starting CarPlay by CID operation. 8 Cannot connect to CarPlay via wireless connection. This symptom possibly occurs after the Ignition Switch was turned Off and On abruptly. 9 POI Search Result shows only city names and distances (without unit) when voice recognition POI search with Category name like “Find toll gate” is used. 10 Navigation restarts itself, when the letters are rashly entered or deleted using keyboard function to search destination. 11 “Manage Route” button is not displayed when touching the route line on Navigation system, when the route search criteria got changed in the Route Preference Screen after a route had been searched. Continued... Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 29 of 30 Number Symptoms to be Improved: 12 “Manage Route” button is not displayed and buttons on the Current Route Screen become unselectable (turns to grayish fill) when the Navigation system is operated in the sequence of “Manage Route” > “Avoid Blocked Road” (in the Current Route Screen) > “Back.” 13 After the FOTA is completed, the CCM does not send the confirmation data to the server even though it displays pop-up message of completion. The status is updated when the FOTA operation is made next time. 14 A pop-up message of “Connection Error” is displayed when the pop-up message of Service Appointment Scheduler Popup is displayed after the engine was turned on and the “Read Now” button is pressed immediately after that. 15 Pop-up message ”Please go to your retailer to update the Gracenote Database” appears every time CP1 system is rebooted due to interruption of CP1 software update via USB port (ACC OFF or BATT power remove etc.) *** Note*** In case this USB update failure occurs, retry updating according to the instructions in “Appendix C” Bulletin Number: 15-305-22R; Revised: 03/09/23 Page 30 of 30