22-NA-147

Service Bulletin
Bulletin No.:
22-NA-147
Date:
April, 2023
TECHNICAL
Subject:
Service 4–Wheel Drive Message Illuminated in DIC with DTC C15AC Set
Brand:
Model:
Chevrolet
GMC
Model Year:
Breakpoint:
from
to
from
to
Silverado
2500HD/3500HD
2020
2023
SOP
Built prior to
July 1, 2022
Sierra
2500HD/3500HD
2020
2023
SOP
Built prior to
July 1, 2022
Engine:
Transmission:
Involved Region or Country
United States
Additional Options (RPOs)
Equipped with RPO NQF
Condition
Some customers may comment on Service 4-wheel drive message on the DIC (Driver
Information Center).
Technician may find DTC C115AC current or in history.
Cause
The cause of the condition may be software anomalies with the Transfer Case Control
Module.
Correction
Verify the software in the Transfer Case Control Module.
• If the TCCM isn’t up to date then reprogram the TCCM, refer to the Service Procedure
below.
• If the TCCM has the latest software update, them complete a Transfer Case Actuator
Learn Procedure.
Service Procedure
Important: Service agents must comply with all
International, Federal, State, Provincial, and/or
Local laws applicable to the activities it performs
under this bulletin, including but not limited to
handling, deploying, preparing, classifying,
packaging, marking, labeling, and shipping
dangerous goods. In the event of a conflict between
the procedures set forth in this bulletin and the
laws that apply to your dealership, you must follow
those applicable laws.
Caution: Before downloading the update files, be sure
the computer is connected to the internet through a
network cable (hardwired). DO NOT DOWNLOAD or
install the files wirelessly. If there is an interruption
during programming, programming failure or control
module damage may occur.
• Ensure the programming tool is equipped with the
latest software and is securely connected to the
data link connector. If there is an interruption
during programming, programming failure or
control module damage may occur.
Copyright 2023 General Motors LLC. All Rights Reserved.
•
•
•
•
Stable battery voltage is critical during
programming. Any fluctuation, spiking, over
voltage or loss of voltage will interrupt
programming. Install a GM Authorized
Programming Support Tool to maintain system
voltage. Refer to www.gmdesolutions.com for
further information. If not available, connect a fully
charged 12 V jumper or booster pack
disconnected from the AC voltage supply. DO
NOT connect a battery charger.
Follow the on-screen prompts regarding ignition
power mode, but ensure that anything that drains
excessive power (exterior lights, HVAC blower
motor, etc) is off
Please verify that the radio time and date are set
correctly before inserting USB drive into vehicle
for programming, otherwise an error will result..
Clear DTCs after programming is complete.
Clearing powertrain DTCs will set the Inspection/
Maintenance (I/M) system status indicators to NO.
Page 2
April, 2023
Important: The service technician always needs to
verify that the VIN displayed in the TLC left side drop
down menu and the top center window match the VIN
plate of the vehicle to be programmed prior to using
Service Programming System 2 (SPS2) for
programming or reprogramming a module.
• For the TLC application, service technicians need
to always ensure that the power mode (ignition) is
“ON” before reading the VIN from the vehicle’s
VIN master module and that they do not select a
VIN that is already in the TLC application memory
from a previous vehicle.
• If the VIN that shows up in the TLC top center
window after correctly reading the VIN from the
vehicle does not match the VIN plate of the
vehicle, manually type in the VIN characters from
the vehicle VIN plate into the TLC top center
window and use these for programming or
reprogramming the subject module with the
correct vehicle VIN and software and/or
calibrations.
• The Engine Control Module (ECM) is the master
module (for VIP vehicles) that TLC reads to
determine the VIN of the vehicle. If the VIN read
from the vehicle by TLC does not match the VIN
plate of the vehicle, the ECM also needs to be
reprogrammed with the correct VIN, software and
calibrations that match the vehicle’s VIN plate.
• The Body Control Module (BCM) is the master
module (for GEM vehicles) that TLC reads to
determine the VIN of the vehicle. If the VIN read
from the vehicle by TLC does not match the VIN
plate of the vehicle, the BCM also needs to be
reprogrammed with the correct VIN, software and
calibrations that match the vehicle’s VIN plate.
Bulletin No.: 22-NA-147
Bulletin No.: 22-NA-147
April, 2023
Page 3
Caution: Be sure the VIN selected in the drop down
menu (1) is the same as the vehicle connected (2)
before beginning programming.
5743643
Important: If the vehicle VIN DOES NOT match, the
message below will be shown
5877000
Page 4
April, 2023
Bulletin No.: 22-NA-147
5644477
Important: Techline Connect and TIS2WEB screens
shown above.
Important: If the same calibration/software warning is
noted on the TLC or SPS Summary screen, select OK
and follow screen instructions. After a successful
programming event, the WCC is located in the Service
Programming System dialogue box of the SPS
Summary screen. No further action is required. Refer to
the Warranty section of the bulletin.
1. Reprogram the Transfer Case Control Module.
Refer to Transfer Case Control Module
Programming and Setup in SI.
Bulletin No.: 22-NA-147
April, 2023
Page 5
5644478
Note: The screenshots above are an example of
module programming and may not be indicative of the
specific module that is being programmed. Module
selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections,
you MUST record the warranty claim code provided on
the Warranty Claim Code (WCC) screen shown above
on the job card. Refer to callout 1 above for the location
of the WCC on the screen.
2. Record Warranty Claim Code on job card for
warranty transaction submission.
Page 6
April, 2023
Bulletin No.: 22-NA-147
Warranty Information
For vehicles repaired under the Bumper-to-Bumper
coverage (Canada Base Warranty coverage), use the
following labor operation. Reference the Applicable
Warranties section of Investigate Vehicle History (IVH)
for coverage information:
Labor Operation
Description
Labor Time
*2888868
Transfer Case Control Module Reprogramming with SPS for
Service 4-Wheel Drive Message
0.5 hr
*2889478
Transfer Case Actuator Learn Procedure for DTC C15AC
0.3 hr
*This is a unique Labor Operation for Bulletin use only.
Important: **To avoid warranty transaction rejections, carefully read and follow the instructions below:
6125814
•
•
The Warranty Claim Code must be accurately entered in the “SPS Warranty Claim Code” field of the transaction.
When more than one Warranty Claim Code is generated for a programming event, it is required to document all Warranty
Claim Codes in the “Correction” field on the job card. Dealers must also enter one of the codes in the “SPS Warranty Claim
Code” field of the transaction, otherwise the transaction will reject. It is best practice to enter the FINAL code provided by
SPS/SPS2.
Bulletin No.: 22-NA-147
April, 2023
Page 7
Warranty Claim Code Information Retrieval
If the Warranty Claim Code was not recorded on the
Job Card, the code can be retrieved in the SPS2
system as follows:
6125774
1. Open TLC on the computer used to program the
vehicle.
2. Select and start SPS2.
3. Select Settings.
4. Select the Warranty Claim Code tab.
The VIN, Warranty Claim Code and Date/Time will be
listed on a roster of recent programming events. If the
code is retrievable, dealers should resubmit the
transaction making sure to include the code in the SPS
Warranty Claim Code field.
Version
2
Modified
Released July 26, 2022
Revised March 27, 2023 – Updated Labor Time and added additional Labor Operation
under Warranty Information
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these
technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper
service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a
job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your
vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the
information.
WE SUPPORT VOLUNTARY
TECHNICIAN
CERTIFICATION