A3423632070167_1

Technical Service Bulletin
34 Cooling oil valve fails basic settings after repair DTC: P1A5B00
34 23 63 2070167/1 May 12, 2023.
Model(s)
Year
A6
2016 – 2021
A4 allroad, and
A4
2017 – 2021
A5, A5 Cabriolet,
A5 Sportback,
2018 – 2021
and Q5
Q5 e quattro
2020 – 2021
A7 e quattro, and
Q5 Sportback
2021
VIN Range
Vehicle-Specific Equipment
All
0CK, 0HL, 0CJ, or 0DK Transmission
Condition
Customer states:
No customer statement as the DTC entry may occur after replacing the Transmission Control Unit or Valve Body
for another concern.
Workshop findings:
The “Calibration of cooling oil valve” basic setting cannot be performed successfully after a repair.
The following DTC is stored transmission control module (TCM), J217 (address word 0002)
DTC: P1A5B00 “Cooling oil valve, no basic setting” with symptom code 20832
Technical Background
After a repair, the routine for calibrating the cooling oil valve must be performed. Interruptions may occur. The
routine is aborted as the value is outside the tolerance.
Production Solution
Not Applicable
Service
Page 1 of 4
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of
this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
If the event memory entry “P1A5B00: Cooling oil valve, no basic setting” with symptom 20832 is logged after a
repair to the transmission proceed as follows:
Compare the software part number/software version number of the transmission control module (TCM), J217
(address word 0002) (Figure 1) with the software part number/software version number in the SVM Table below.
If the vehicle has an installed software part number and software version number in the SVM table perform repair
option 1. If the vehicle doesn’t have installed software part number and software version number in the SVM table
perform repair option 2.
Figure 1. Software part number/software version
Repair Option 1:
SVM Update Instructions
1. Follow all instructions in TSB 2011732: 00 Software Version Management (SVM), operating instructions.
2. Update the of transmission control module (TCM), J217 (address word 0002) using the SVM action code as
listed in the table below, if necessary:
Model
A4
Installed
Software Part
Number
Installed
Software
Version
8W2927155BP
0002
4K0927153M
0003
4K0927153M
0005
A6/A7
New Software
Part Number
New Software
Version
SVM Code
Input
(or higher)
8W2927155BP
0003
4K0927153M
0007
02A222
No further calibration is then required. The software delivers a default value. The vehicle can therefore be
operated with immediate effect.
Repair Option 2:
If the software part number/software version number is not listed in the SVM table, the complete mechatronic unit
must be replaced according to the repair manual instructions. It is not necessary to adapt the cooling oil valve for
the mechatronic unit available.
After installing the new Mechatronics unit with the scan tool perform the following:
• Activate the new control unit using the Guided Function “0002 - Replace mechatronic unit (control unit)”.
Only perform the following basic settings according to ODIS:
• Calibration of position sensors -G487...G490-
Page 2 of 4
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of
this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
• Adaption of clutch kiss points.
• Calibration of gear sensor -> only for 2016 and 2017 A6 2.0 Front Wheel Drive.
Warranty
Claim Type:
• 110 up to 48 Months/50,000 Miles.
• G10 for CPO Covered Vehicles – Verify Owner.
• If the vehicle is outside any warranty, this Technical Service Bulletin is informational
only.
Service Number:
3511
Damage Code:
0016
Repair Option 1:
Labor Operations:
Software update
0151 0000
Time stated on
diagnostic
protocol
50 TU (Max)
Diagnostic Time:
GFF – Checking and clearing fault codes
included in existing labor operations
No allowance
0 TU
Road test prior to service procedure
No allowance
0 TU
Road test after service procedure
No allowance
0 TU
Remove and install mechatronic unit
3511 19xx
See SRTs with
associated
operations
0150 0000
Time stated on
diagnostic
protocol
Repair Option 2:
(Plus predecessors and items that are included
repair operations)
GFF – Checking and clearing fault codes
included in existing labor operations
100 TU (Max)
Diagnostic Time:
Road test prior to service procedure
No allowance
0 TU
Road test after service procedure
No allowance
0 TU
Claim Comment:
As per TSB 2070167/1
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Page 3 of 4
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of
this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Required Parts and Tools
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Part Number
Part Description
Quantity
See ETKA
Fasteners, Bolts, Nuts and Screws as needed per the
Repair Manual
See ETKA/ELSA
See ETKA
Mechatronics unit (Repair Option 2)
01
(Order to VIN)
Additional Information
All parts and service references provided in this TSB (2070167) are subject to change and/or removal.
©2023 Audi of America, Inc. All rights reserved. The information contained in this document is based on the
latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes
at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Page 4 of 4
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of
this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.