NTB23-051

Classification:
Reference:
RA23-001
Date:
NTB23-051
June 15, 2023
VIBRATION AND/OR NOISE FROM THE REAR OF THE VEHICLE
WHEN TURNING
APPLIED VEHICLES:
2021-2023 Rogue (T33)
APPLIED DATES:
VINs starting with 5N1 – built on or after February 1, 2022
VINs starting with JN8 – built on or after April 26, 2021
APPLIED DRIVETRAINS:
AWD
IF YOU CONFIRM
A binding feeling, vibration, and/or noise coming from the rear end when turning at low
speed,
AND
The issue is resolved by unplugging the Actuator Assembly (AWD Actuator) on the rear
Final Drive Unit.
ACTION
1.
Remove the Electro-hydraulic Coupling Assembly (AWD Coupler).
2.
Clean the Coupling Oil Tank.
3.
Replace the Electro-hydraulic Coupling Assembly (AWD Coupler).
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/4
SERVICE PROCEDURE
Remove the AWD Coupler
1.
Perform Adjustment Before Removal of the AWD Coupler.

2.
Refer to the ESM: TRANSMISSION & DRIVELINE > DRIVELINE > REAR FINAL
DRIVE: R145 > REMOVAL AND INSTALLATION > ELECTRO-HYDRAULIC
COUPLING > Adjustment > ADJUSTMENT BEFORE REMOVAL
Remove the AWD Coupler.

Refer to the ESM: TRANSMISSION & DRIVELINE > DRIVELINE > REAR FINAL
DRIVE: R145 > REMOVAL AND INSTALLATION > ELECTRO-HYDRAULIC
COUPLING > Removal and Installation > REMOVAL
Clean the Coupling Oil Tank
3.
Remove the fill plug from the side of
the coupling oil tank cover.
Coupling oil tank cover
fill plug
Front of vehicle
Figure 1
4.
Spray brake cleaner into the coupling oil tank until clean solvent is running out of the
AWD Coupler fluid hole.
IMPORTANT: Allow the brake cleaner to fully evaporate before proceeding to step 5
on page 3.
AWD Coupler
fluid hole
Coupling oil tank cover fluid fill hole
Brake cleaner
Figure 3
Figure 2
2/4
NTB23-051
Install the New AWD Coupler
5.
Install the new AWD Coupler.

Refer to the ESM: TRANSMISSION & DRIVELINE > DRIVELINE > REAR FINAL
DRIVE: R145 > REMOVAL AND INSTALLATION > ELECTRO-HYDRAULIC
COUPLING > Removal and Installation > INSTALLATION
IMPORTANT: Only use the fluid listed in the PARTS INFORMATION. The fluid
has a tendency to have clutch additive separate during long storage, it is critical to
shake the fluid for 30-60 seconds before using.
6.
Perform Adjustment After Installation of the AWD Coupler.

Refer to the ESM: TRANSMISSION & DRIVELINE > DRIVELINE > REAR FINAL
DRIVE: R145 > REMOVAL AND INSTALLATION > ELECTRO-HYDRAULIC
COUPLING > Adjustment > ADJUSTMENT AFTER INSTALLATION
IMPORTANT: The AIR BLEEDING AND INITIALIZE OIL DETERIORATION
LEVEL process will need to be performed several times until there is no noise
from the Final Drive Unit.
7.
Record the Final Drive Unit
manufacture date on the Repair Order.
HINT:
o The manufacture date is
located in the casting stamp
located on the rear passenger
(RH) side of the Final Drive
Unit.
o For example, Figure 4 has a
casting stamp of FF210817B.
The manufacture date is
08-17-2021.
3/4
Figure 4
NTB23-051
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
COUPLING ASSY-ELECTRICAL
LIMITED SLIP COUPLER TRANSMISSION FLUID
12-301 (1) (2)
38760-6RE3A
1
999MP-LSCTRF
As needed
(1)
Order this item through the Nissan Maintenance Advantage program: Phone 877-NISNMA1 (877-647-6621). Website order via link on the dealer portal; www.NNAnet.com
and click on the “Maintenance Advantage-Tire/Battery/Chemical” link.
(2)
This fluid has a tendency to have clutch additive separate during long storage, it is
critical to shake the fluid for 30-60 seconds before using.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
Replace AWD Electronic Coupling
Assembly & Clean Oil Tank
(1)
PFP
OP CODE
SYM
DIA
FRT
(1)
LX13AA
ZE
32
1.8
Reference the electronic parts catalog and use the Electric Coupling (38760-*****) as
the Primary Failed Part (PFP).
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
June 15, 2023
NTB23-051
DESCRIPTION
Original bulletin published
4/4
NTB23-051