A6923902051242_7

Technical Service Bulletin
69 Airbag warning light on, DTC B1225F1 stored in the airbag control module
69 23 90 2051242/7 June 2, 2023. Supersedes Technical Service Bulletin Group 69 number 22-86 dated May 4,
2022, for reasons listed below.
Model(s)
Year
A4 allroad, A4,
and Q7
2017 – 2019
S4, A5, A5
Cabriolet, A5
Sportback, S5,
2018 – 2019
S5 Cabriolet, S5
Sportback, RS 5,
Q5, and SQ5
RS 5 Sportback
VIN Range
Vehicle-Specific Equipment
All
Not Applicable
2019
Condition
REVISION HISTORY
Revision
Date
Purpose
7
-
Revised Warranty (Updated Labor Operations)
6
05/04/2022
Revised Service (Added note for Campaign 74E3)
5
07/24/2019
Revised Condition (Removed Note)
Customer states:
• Airbag warning lamp is illuminated in the driver information system (DIS).
• Customer may also report that the passenger airbag indicator lamp in the overhead console may show that the
airbag is off.
Workshop findings:
The following DTC is stored in the airbag control module, J234 (address word 0015):
• DTC B1225F1 (Seat occupied recognition sensor mat Shield wire, open circuit).
Technical Background
Not Applicable
Page 1 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Production Solution
There is a concern with the aluminum shielding on the PODS harness under the seat that is causing the DTC
B1225F1 to occur. The aluminum sleeve isn’t fitted tight enough to the harness, a small amount of interference is
possible and causes the fault.
The service solution is to apply cable ties at two different points of the harness under the seat which tightens the
fit of the aluminum shielding and corrects the issue.
Service
A4 and A5
1. Do not follow this TSB. Please perform Campaign 74E3 instead.
Q7
1. To apply the cable ties, the seat does not need to be removed. You will need to move the lateral seat
adjustment all the way to rearmost adjustment limit and the vertical height adjustment all the way to the
upper adjustment limit.
Once the seat is adjusted to the above-mentioned position, you will see the need to attach the cable ties at
two points on the harness as shown (Figure 1).
Page 2 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 1. Positions of the cable ties.
Note:
You are not going to secure the harness to any part of the seat with the cable ties, you are only applying the
cable ties to the harness to apply clamping force to the harness and shielding. DO NOT ATTACH THE
HARNESS TO THE SEAT FRAME.
2. You will attach the first cable tie in the yellow marked area on the harness between the cable tie clip and the
crossbar tube as shown below (Figure 2).
Page 3 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 2. Attach the first cable tie in the yellow area.
3. The second cable tie position is to the rear of the crossbar tube where the harness drops down from the
frame. Place the cable tie in the yellow marked area shown below (Figure 3).
Page 4 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 3. Attach the second cable tie to the yellow marked area.
Note:
When tightening the cable ties, only tighten them with your hands, do not use any tools to tighten the cable tie as
this can damage the harness. Check that the cable ties cannot be rotated on the harness by hand, to ensure
that proper tension is achieved. Then cut off the excess length from the tie wrap.
4. Once you have the cable ties properly secured and installed, return the seat to the original position and clear
the faults stored in the system.
Q5
Page 5 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
1. To apply the cable ties, the seat does not need to be removed. You will need to move the lateral seat
adjustment all the way to rearmost adjustment limit and the vertical height adjustment all the way to the
upper adjustment limit.
Once the seat is adjusted to the above-mentioned position, you will see the need to attach the cable tie at
two points on the harness as shown (Figure 4-6).
Figure 4. Positions of the cable ties (front to back).
Page 6 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 5. Positions of the cable ties (back to front).
Note:
You are not going to secure the harness to any part of the seat with the cable ties, you are only applying the
cable ties to the harness to apply clamping force to the harness and shielding. DO NOT ATTACH THE
HARNESS TO THE SEAT FRAME.
2. You will attach the first cable tie in the yellow marked area on the harness between the cable tie clip and the
crossbar tube (Figure 2).
3. The second cable tie position is to the rear of the black 8-pin connector (T8m) for the backrest and lumbar
adjustment and in front of the harness push pin (Figure 6).
Page 7 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 6. Position of second cable tie behind the 8-pin connector.
Note:
When tightening the cable ties, only tighten them with your hands, do not use any tools to tighten the cable tie as
this can damage the harness. Check that the cable ties cannot be rotated on the harness by hand, to ensure
that proper tension is achieved. Then cut off the excess length from the tie wrap.
4. Once you have the cable ties properly secured and installed, return the seat to the original position and clear
the faults stored in the system.
Page 8 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
Warranty
Claim Type:
• 110 up to 48 Months/50,000 Miles.
• G10 for CPO Covered Vehicles – Verify Owner.
• If the vehicle is outside any warranty, this Technical Service Bulletin is
informational only.
Service Number:
7210
Damage Code:
0018
Labor Operations:
Seat Wiring Harness Repair
7210 4199
25 TU
Diagnostic Time:
GFF – Checking and clearing fault codes
0150 0000
20 TU
Road test prior to service procedure
No allowance
0 TU
Road test after service procedure
No allowance
0 TU
As per TSB 2051242/7
Claim Comment:
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Required Parts and Tools
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Part Number
Part Description
Quantity
N 90937702
Cable strap
02
See ETKA
Fasteners, Bolts, Nuts, and Screws as needed per the
Repair Manual
See ETKA/ELSA
Additional Information
All parts and service references provided in this TSB (2051242) are subject to change and/or removal.
©2023 Audi of America, Inc. All rights reserved. The information contained in this document is based on the
latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes
at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
Page 9 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.
Technical Service Bulletin
these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Page 10 of 10
© 2023 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights
of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without
the prior expressed written permission of the publisher.