No. 1-21
Service Bulletin Details
Public Details for: No. 1-21
Installation and conversion instructions for the front camera on the macan.
Models from 2021
2021 PORSCHE MACAN |
2021 PORSCHE MACAN GTS |
2021 PORSCHE MACAN S |
2021 PORSCHE MACAN TURBO |
Models from 2020
2020 PORSCHE MACAN |
2020 PORSCHE MACAN GTS |
2020 PORSCHE MACAN S |
2020 PORSCHE MACAN TURBO |
Installation and Conversion Instructions Macan (95B) 1/21 ENU 9163 9 PORSCHE Front Camera (Dashcam) Revision: This bulletin replaces bulletin Group 9 1/21, dated March 2, 2022. Model Year: As of 2019 up to 2021 Restrictions: Approved for the following markets/countries: • Information: USA (C02) and Canada (C36) Retrofitting Figure 1 Note: The Porsche front camera (dashcam Figure 1) is affixed to the LEFT of the interior mirror (viewed in direction of travel) on the windshield and is connected to the vehicle electrical system. It is ideal for making video recordings of driving situations and while parking. It can be configured and operated using a related app on your smartphone. Recorded videos are stored on the supplied SD card and previous recordings are overwritten. If the dashcam detects a shake/vibration or if the radar sensor is triggered, the recorded video is stored separately and not overwritten. Recordings can be downloaded directly from the SD card or via the app. Tequipment Aug 11, 2023 Page 1 of 22 9 Macan (95B) 9163 ENU 1/21 Installation and Conversion Instructions Information Important information for customers/customer service advisors: • Ask customers to download and install the "Porsche Dashcam App" from the App Store (Apple or Google Play) on their device (smartphone/tablet) in advance. For vehicle handover: • Recommendation: If the vehicle is present, connect the Porsche front camera WiFi to the vehicle WiFi (see also vehicle operating instructions Porsche Connect). • Together with the customer, check whether a firmware update via "Porsche Dashcam App" is necessary. Perform the firmware update together if necessary. • Together with the customer, choose the "Region/State/Country" by selecting the relevant flag and format the SD card. Further information for customers: Parts Info: Aug 11, 2023 Page 2 of 22 • The customer is responsible for choosing the right "Region/State/Country"! • After crossing a national border: Update the "Region/State/Country" (see also conditions of use for this topic)! 9Y0.044.930 PORSCHE front camera (dashcam), set Tequipment Installation and Conversion Instructions Macan (95B) 1/21 ENU 9163 9 Parts List: Figure 2 ——— 1x 3M privacy film (front & rear camera) Figure 2 -1- ——— 1x Front camera Figure 2 -2- ——— 1x ——— 1x ——— 1x ——— 3x Micro SD memory card (32 GB, plugged into front camera) Figure 2 -3Front camera retainer plate assembly with wire harness Figure 2 -4Wire harness assembly with connector (3-pin, wire approx. 4 m long) Figure 2 -5Protective foam roll (∅ approx. 29 x 74) Figure 2 -6- ——— 7x Tie-wrap, 145 x 3.6 x 1.1 Figure 2 -7- N.907.326.01 4x Socket contact, 4.8 x ∅ 1.0 mm² Figure 2 -8- N.907.327.01 2x N.906.844.01 3x 999.650.136.22 4x Socket contact, 4.8 x ∅ 2.5 mm² (standard power timer) Figure 2 -9Socket contact, 2.8 x ∅ 1.0 mm² (junior power timer) Figure 2 -10Socket contact, 5.0 x ∅ 1.0 mm² Figure 2 -11- N.017.506.5 2x Cable ring eyelet, A6 Figure 2 -12- 992.971.859.B 2x Cable ring eyelet, M8 Figure 2 -13- Tequipment Aug 11, 2023 Page 3 of 22 9 Macan (95B) 9163 Repair Kits: ENU Installation and Conversion Instructions 1/21 N.102.615.01 2x Blade-type fuse, 5 amp (mini) Figure 2 -14- N .017.131.16 2x Blade-type fuse, 5 amp Figure 2 -15- ——— 1x PORSCHE dashcam operating instructions Figure 2 -16- ONLY order when replacing the windshield/rear window: 9Y0.044.931 1x “Adhesive pad” repair kit, includes: ——— 1x ——— 1x Adhesive pad for front camera retainer plate (grey) on backing sheet Adhesive pad for rear camera (grey) ——— 1x 3M privacy film (front & rear camera) Figure 2 -1- ONLY order if front camera “wiring harness” is damaged: 9Y0.044.931 1x “Adhesive pad” repair kit 9Y0.044.932 1x Wiring harness repair kit, includes: ——— 1x ——— 1x ——— 3x Front camera retainer plate assembly with wire harness (WITHOUT adhesive pads, similar to Figure 2 -4-) Wire harness assembly with connector (3-pin, wire approx. 4 m long) Figure 2 -5Protective foam roll (∅ approx. 29 x 74) Figure 2 -6- ——— 7x Tie-wrap, 145 x 3.6 x 1.1 Figure 2 -7- ——— 1x Bag with socket contacts, cable ring eyelets and fuses Figure 2 -8-15- Technical Details: • • • • • • • Materials: ——— 1x Auxiliary line (Tekalan or Teflon hose) approx. 1,500 mm long ——— 1x Wrapping/insulating tape (commercially available) ——— 1x Cleaning cloth (commercially available) ——— 1x Isopropanol (commercially available) Tools: Video recording in Quad High Definition (QHD) Lens with polarization filter to reduce reflections and improve colors and contrasts Audio recording (can be deactivated) Global positioning system (GPS) sensor Vibration sensor Radar sensor for video recording when an object is approaching the vehicle Bracket for the windshield for fixed mounting on the vehicle P90999 - P90999 - Porsche Tester 4th generation Tablet, smartphone or PC with Internet access Marking pencil/chalk Flashlight Plastic squeegee Aug 11, 2023 Page 4 of 22 Tequipment Installation and Conversion Instructions Assembly: 1 Macan (95B) 1/21 ENU 9163 9 Preliminary work 1.1 Clean inside and outside of the windshield. 1.2 Connect a battery charger. Workshop Manual '2X00IN Work instructions after disconnecting the battery'. 1.3 Expose front roof/(interior) rear-view mirror area 1.4 1.3.1 Remove front roof console. Workshop Manual '708319 Removing and installing front roof console' 1.3.2 Remove (left) sun visor. Workshop Manual '682319 Removing and installing sun visor' 1.3.3 Remove front (left) grab handle. Workshop Manual '683519 Removing and installing front handle' Expose (left) A-pillar area 1 2 3 – Dashboard trim panel – Air vent (instrument cluster) – Trim panel under dashboard 1.4.1 Remove dashboard trim panel (at the left). Figure 3, Workshop Manual '701619 Removing and installing dashboard trim panel' 1.4.2 Remove front side-section trim panel (at the left). Workshop Manual '702419 Removing and installing front side-section trim panel' 1.4.3 Figure 3 Remove A-pillar trim panel (at the left). Workshop Manual '705719 Removing and installing A-pillar trim panel' Tequipment Aug 11, 2023 Page 5 of 22 9 Macan (95B) 9163 ENU Installation and Conversion Instructions 1/21 1.4.4 Remove front inner door sill trim. Figure 4, Workshop Manual '680519 Removing and installing (front) inner door sill trim' 1 2 – Front lid release – Front inner door sill trim (on driver’s side) Figure 4 1.5 Expose fuse box on dashboard (at the left) 1 2 3 4 1.5.1 – – – – Air vent (instrument cluster) Dashboard moulding (right) Air vent unit (PCM) Trim panel under dashboard Removing trim panel under dashboard (left side,):. Figure 5 (LHD vehicle) -4LHD vehicles: Workshop Manual '701919 Removing and installing trim panel under dashboard on driver’s side' 1.5.2 1.6 Aug 11, 2023 Page 6 of 22 Figure 5 (LHD vehicle) Loosen fuse box on dashboard (at the left). Workshop Manual '978409 Loosening and securing fuse box' Loosening front roof trim panel. Workshop Manual '708419 Removing and installing roof trim panel' Tequipment Installation and Conversion Instructions 2 Macan (95B) 1/21 ENU 9163 9 Install PORSCHE front camera (dashcam) in the vehicle Overview of installation position Figure 6 1 2 3 4 5 2.1 – Interior mirror – Installation position of PORSCHE front camera (dashcam) – Electric wire harness – Fuse box on dashboard (at the left) – Ground pin Position front camera (dashcam) to the LEFT of the interior mirror on the windshield Figure 6 2.1.1 Install retainer plate with wire harness on the base of the front camera until the locking mechanism engages. Figure 7 1 2 – Retainer plate with wire harness – Front camera base Figure 7 Tequipment Aug 11, 2023 Page 7 of 22 9 Macan (95B) 9163 ENU Installation and Conversion Instructions 1/21 2.1.2 Trace the outline of the foot of the interior mirror on the outside of the windshield using a marking pencil/chalk. Figure 8 -11 2 3 4 X Z 2.1.3 – Outline of foot of interior mirror – Outline of front camera base – Interior mirror – Front camera – 216 mm/ 8.5 in – 108 mm/ 4.25 in Copy dimensions X and Z on the windshield. Figure 8 -topDimension X = distance from lower edge of outline of front camera base to edge of roof: Length 216 mm/ 8.5 in Figure 8 Dimension Z = distance from inner edge of outline of front camera base to inner edge of outline of foot of interior mirror: Length 108 mm/ 4.25 in Information Observe the following points during positioning/alignment: 2.2 • Sufficient distance between front camera and interior mirror base: at least 5 mm/ 0.2 in! • Get another person standing in front of the vehicle to check and confirm the horizontal alignment of the camera with the PORSCHE logo! 2.1.4 Position front camera with retainer plate in the vehicle at the marking on the windshield. Figure 8 -Arrows- 2.1.5 Get another person to trace and shade in the outline of the retainer plate on the outside of the windshield using a marking pencil/chalk. 2.1.6 Clean the inside of the windshield in the bonding area for the retainer plate (shaded area) to remove any dust and grease. Install front camera (dashcam) on the windshield NOTICE Adhesive films not prepared/installed correctly Aug 11, 2023 Page 8 of 22 • Damage to adhesive films • Inadequate adhesion of adhesive films Tequipment Installation and Conversion Instructions Macan (95B) 1/21 ENU 9163 9 Carefully clean the areas on which you intend to stick the film to ensure that all traces of oil, grease and silicone are completely removed. Do not touch the bonding surfaces. Object (adhesive film, vehicle, etc.) and ambient temperature: Minimum temperature 15°C / 59°F. 2.2.1 Pull 3M privacy film off the backing sheet. Figure 9 -A1 2 3 – 3M privacy film – Marked bonding surface – Interior mirror base 2.2.2 Position 3M privacy film on the marked bonding surface on the windshield. Figure 9 -B- 2.2.3 Carefully affix 3M privacy film using a plastic squeegee, starting from the center and moving towards the edge. Figure 9 Tequipment Aug 11, 2023 Page 9 of 22 9 Macan (95B) 9163 ENU Installation and Conversion Instructions 1/21 2.2.4 Pull protective film off the front camera retainer plate. Figure 10 -top1 2 3 4 – – – – Protective film Front camera 3M privacy film Interior mirror Information Observe the following points during positioning/alignment: • Sufficient distance between front camera and interior mirror base: at least 5 mm/ 0.2 in! • Get another person standing Figure 10 in front of the vehicle to check and confirm the horizontal alignment of the camera with the PORSCHE logo! Align front camera with retainer plate symmetrically with respect to the 3M privacy film. Figure 10 -Bottom2.2.5 3 Press front camera with retainer plate firmly onto the 3M privacy film on the windshield. Route and connect electric wire harness 1 2 3 4 5 – Interior mirror – Installation position of PORSCHE front camera (dashcam) – Electric wire harness – Fuse box on dashboard (at the left) – Ground pin Line routing ( Figure 11): • Front camera → headliner/roof console → along windshield frame → left A-pillar (top) → along A-pillar → fuse carrier on dashboard, left → ground pin (LHD: MB21) Figure 11 Information Route electric wire harness along existing wiring, if installed. Make sure that safety components (airbags, etc.) are still working correctly! Aug 11, 2023 Page 10 of 22 Tequipment Installation and Conversion Instructions 3.1 Macan (95B) 1/21 ENU 9163 9 Routing wire harness 3.1.1 On the connector side, push one protective foam roll onto the wire harness for the front camera retainer plate and the (3-wire) wire harness. 1 2 3 4 – Protective foam roll – Wire harness on front camera retainer plate – Wire harness (3-wire) – Branch for 2nd camera 3.1.2 Connect plug connection (3-pin). Figure 12 -Arrows- 3.1.3 Guide wire harness for front camera (dashcam) vertically with respect to the headliner/roof console. 3.1.4 Push protective foam roll over the (3-pin) plug connection. 1 2 3 Figure 12 – Wire harness for front camera (dashcam) – Protective foam roll – Tie-wrap Secure (3-pin) plug connection to existing components/lines under the headliner in the roof console area using tie-wraps. Figure 13 3.1.5 Figure 13 Branch for 2nd camera and secure it to existing components/lines in the roof console area using another protective foam roll. Figure 12 -4- Tequipment Aug 11, 2023 Page 11 of 22 9 Macan (95B) 9163 ENU Installation and Conversion Instructions 1/21 3.1.6 Route the rest of the wire harness as follows: 1 2 • 3.2 – Wire harness for front camera (dashcam) – Fuse carrier on dashboard (left) Roof console → under headliner along windshield frame → left A-pillar (top) → along A-pillar → fuse carrier on dashboard (left Figure 14 (LHD vehicle)) → BK 0.5² line → ground pin (LHD: MB21) Connect electric wire harness Figure 14 (LHD vehicle) Function/line: Connection point on left-hand drive (LHD) vehicle Weight Terminal 31 = BK; 0.5² Cable ring eyelet A6 (N.017.506.5) on ground pin MB21 (left A-pillar) Ignition positive Terminal 15 = GN; 0.5² Socket contact, 4.8 x ∅ 1.0 mm² (N.907.326.01) in slot 9, fuses in row A (A9) If used for ERA Glonass: Double connector on line RD/WH 0.5² Permanent positive Terminal 30 = RD; 0.5² Aug 11, 2023 Page 12 of 22 Socket contact, 4.8 x ∅ 1.0 mm² (N.907.326.01) in slot 2, fuses in row C (C2) 3.2.1 Open fuse holder as shown in the table. 3.2.2 Shorten lines GN; 0.5² and RD; 0.5² to the relevant fuse holders and crimp the relevant contacts. Tequipment Installation and Conversion Instructions 3.2.3 Macan (95B) 1/21 ENU 9163 9 Connect power supply as shown in the table ( Figure 15 (LHD vehicle)). 1 2 3 4 – Fuse carrier on dashboard (left) – Line GN; 0.5² (terminal 15) – Line RD; 0.5² (terminal 30) – BK; 0.5² line (terminal 31) 3.2.4 Close fuse holders and install with the fuse carrier into the dashboard. Workshop Manual '978409 Loosening and securing fuse box' 3.2.5 Protect the front camera power supply with new fuse(s). Fuse: Setpoint value 5 A Figure 15 (LHD vehicle) 3.2.6 Route BK; 0.5² line (terminal 31) to ground pin MB21 or MB22, shorten it and install it on ground pin using cable ring eyelet A6. Figure 16 1 2 – BK; 0.5² line (terminal 31) – Ground pin MB21 (left-hand drive) Tightening torque 9 Nm (6.6 ftlb.) 3.3 4 Secure routed wire harness to existing lines/components in the vehicle with tie-wraps without tensile stress and so that no chafing occurs. Interior finishing work 4.1 Secure the front headliner. Workshop Manual '708419 Removing and installing roof trim panel' 4.2 Assemble fuse box area on the dashboard (left). 4.3 Assemble inner door sill trim and (left) A-pillar area. 4.4 Assemble (internal) rear-view mirror and front roof area. Tequipment Figure 16 Aug 11, 2023 Page 13 of 22 9 Macan (95B) 9163 Coding: ENU 5 Installation and Conversion Instructions 1/21 Code the PORSCHE front camera (dashcam) in Dealer mode 5.1 Preparatory work 1 2 3 4 5 6 5.2 – – – – – – PORSCHE front camera Micro SD memory card (32 GB) Retainer plate Power button WiFi status LED display PRESS (release button) 5.1.1 Remove micro SD memory card (32 GB, Figure 17 -2-) from card slot for front camera. 5.1.2 Figure 17 With the ignition switched on, push the front camera (dashcam Figure 17 -1-) into the retainer plate on the windshield ( Figure 17 -3-) 5.1.3 Press the power button ( Figure 17 -4-) for 10 seconds until you hear the second double beeping sound. 5.1.4 The front camera (dashcam) starts in Dealer mode: WiFi LED ( Figure 17 -5-) lights up "yellow". Connect the front camera (dashcam) to the device (tablet, smartphone or PC) Information The "Dealer mode" network ID name ends with a "D". A password is NOT required! The language setting can be changed by following the menu prompts after opening the first page. 5.2.1 Search available networks for Dealer mode WiFi. 5.2.2 Open Dealer mode on the device (tablet, smartphone or PC) using any browser. To do this, enter "192.168.1.1/diagnostics" in the browser's address line. 5.2.3 Aug 11, 2023 Page 14 of 22 Displays in "Dealer mode" main menu: Tequipment Installation and Conversion Instructions Macan (95B) 1/21 ENU 9163 9 Options: ( Figure 18) 1 2 – Browser's address line – "Options" menu item Figure 18 Diagnostics: ( Figure 19) 1 2 5.3 – Browser's address line – "Diagnostics" menu item Basic settings for front camera (dashcam) in the "Options" menu item ( Figure 18) Figure 19 Tequipment Aug 11, 2023 Page 15 of 22 9 Macan (95B) 9163 ENU Installation and Conversion Instructions 1/21 5.3.1 Change the default language "English" to the desired language: 1 2 – Default language "English" – German For example: German ( Figure 20) • Up to 19 different languages can be selected. Figure 20 Information ONLY for cameras with serial numbers "PDF2101*****", the country can be selected directly via the app on the customer's device (smartphone/tablet). Country selection is possible for cameras, starting with the serial number "PDF2102*****"! If the relevant country is NOT displayed in the drop-down menu: Please select “Global”. 5.3.2 Select the country ( Figure 21). 1 2 3 • • • Aug 11, 2023 Page 16 of 22 – Serial number of front camera (dashcam) – Country – Great Britain Up to 48 countries are currently available for selection. The Country selection screen includes, for example: Units of measurement, frequencies Figure 21 and also legal regulations of the respective country. Macan: Choose Region/State/Country by selecting the appropriate flag. Tequipment Installation and Conversion Instructions 5.3.3 Macan (95B) 1/21 ENU 9163 9 Select the required camera channel ( Figure 22). 1 2 • – Channel – Front + Rear TEQUIPMENT: "Front Only" (front camera) is preset. Figure 22 Information Check which vehicle electrical system battery is installed in the vehicle if necessary by entering the vehicle identification number (VIN) in the Porsche Central Service System (PCSS). Background: The front camera shuts down if the correct battery voltage (switch-off threshold) is not reached over a period of 5 minutes. • Switch-off threshold for lead-acid battery (PbAcid) = 11 V • Switch-off threshold for lithium-ion battery (LiFePO) = 13 V Tequipment Aug 11, 2023 Page 17 of 22 9 Macan (95B) 9163 ENU Installation and Conversion Instructions 1/21 5.3.4 Select the battery type ( Figure 23) 1 2 • • – Battery – PbAcid Select the vehicle electrical system battery installed in the vehicle. Macan: Lead-acid battery (PbAcid) Figure 23 5.3.5 Select Park mode ( Figure 24) 1 2 • • – Park mode – Off Depending on the approval for the respective vehicle. Macan: Select "On". Figure 24 Aug 11, 2023 Page 18 of 22 Tequipment Installation and Conversion Instructions 5.3.6 1/21 ENU 9163 9 Select the time limit ( Figure 25) 1 2 • • 5.4 Macan (95B) – Time limit until radar/video is switched off – 1 hour Turn off radar/video monitoring in Park mode (battery management). After the selected time limit, fast activation of the monitoring system ONLY occurs if the vehicle shakes/vibrates! Macan: Skip. Leave the default setting. Cancel Dealer mode (WiFi LED is still yellow) 5.4.1 Close the browser and switch off ignition. 5.4.2 Pull the front camera (dashcam) off the retainer plate by pressing "PRESS" (release button). 5.4.3 Insert micro SD memory card (32 GB) in the front camera (dashcam). 5.4.4 Install the front camera (dashcam) in the retainer plate. Figure 25 5.5 The settings configured under Step 5.3 are set when the ignition is switched on again. 5.6 Format the micro SD memory card (32 GB) 5.6.1 Switch on ignition. 5.6.2 Press the power button quickly 6 times in a row within 3 seconds. Announcements via front camera speaker: "Formatting..." and "Formatting complete." Diagnostics: 6 Perform diagnostics on front camera (dashcam) – ONLY if necessary! Information can be displayed, function tests can be run and results can be stored in the "Diagnostics" menu item. Tequipment Aug 11, 2023 Page 19 of 22 9 Macan (95B) 9163 ENU 6.1 Installation and Conversion Instructions 1/21 Information about the model name, hardware and software version, radar and more ( Figure 26). 1 2 3 – Model name – Hardware version – Software version Figure 26 6.2 Display of live images from front camera, connection status, memory card status, GPS and radar status and more ( Figure 27). 1 2 3 4 5 – – – – – Front camera live image Rear camera status (if installed) Micro SD memory card contents GPS status GPS coordinates Figure 27 Aug 11, 2023 Page 20 of 22 Tequipment Installation and Conversion Instructions 6.3 Assembly: 7 1/21 ENU 9163 9 Display of radar status, possible tests for LED lights, loudspeaker and microphone ( Figure 28) 1 2 3 4 6.4 Macan (95B) – – – – Radar status LED Lights test Loudspeaker test Microphone test The fault report can be stored on the micro SD memory card (32 GB). To do this, use micro SD memory card in Dealer mode and select "Diagnostics" menu item in the front camera. Concluding work 7.1 Select the fault memory of all systems, work through any existing faults and erase the fault Figure 28 memory. Workshop Manual '0X03IN Diagnostics maintenance: Diagnostic system and maintenance inter...' 7.2 Disconnect the battery charger. Workshop Manual '2X00IN Work instructions after disconnecting the battery'. 7.3 Vehicle handover to customer Information Please pass all this information on to the customer. Also give the customer the PORSCHE dashcam operating instructions. Also give the first 3 pages of these Installation and Conversion Instructions to the customer. 7.3.1 Download the app from the App Store to the customer’s device (smartphone/tablet). 7.3.2 If the vehicle is present, connect the Porsche front camera WiFi to the vehicle WiFi (see also vehicle operating instructions Porsche Connect). 7.3.3 Select and set Region/State/Country (flag) in the app on the customer’s smartphone/tablet. 7.3.4 Have the customer update firmware using the app. 7.3.5 Format micro SD memory card (32 GB). Tequipment Aug 11, 2023 Page 21 of 22 9 Macan (95B) 9163 91 63 23 40: ENU 1/21 Installation and Conversion Instructions –PORSCHE front camera (dashcam) (1x) retrofitted– Includes: Retainer plate for PORSCHE front camera (dashcam) installed on windshield; Route and connect electric wire harness, Format coding of the PORSCHE front camera (dashcam) in dealer mode and micro SD memory card, Read out fault memory, process and delete errors. Labor time: 263 TU Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed. © 2023 Porsche Cars North America, Inc. Aug 11, 2023 Page 22 of 22 Tequipment