ReportE
Service Bulletin Details
Public Details for: ReportE
Audi technician report
- 2015 -
Models from 2015
2015 AUDI Q5 |
2015 AUDI Q5 HYBRID |
2015 AUDI SQ5 |
PERFECT DELIVERY INSPECTION (PDI) 2015 Q5/Q5 hybrid/SQ5/Q5 TDI Audi Technician Report Stock No. Dealer Number R.O. No. VIN Road test mileage out Road test mileage in All items must be completed prior to customer delivery by an Audi technician (for Audi Q5 hybrid, only “Hybrid Aware” techs are able to PDI the hybrid) *Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests **Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection Open Campaigns/Updates Check Elsa for open campaigns and updates. Perform campaigns not requiring SVM if applicable. Campaigns requiring SVM should only be performed after the vehicle has been taken out of transport mode Battery Inspection Check battery clamps for proper torque. Re-torque if required Perform the A-battery test for new batteries using GFF in ODIS Diagnosis –> Special functions –>Service work. Select option 2, the battery test for new batteries as part of the pre–delivery inspection and act according to the test result (ok, recharge, replace). Ensure diagnosis log is uploaded to the GFF paperless server by selecting “ok” when tester wants to send the current generated diagnosis protocol online. (Note: Do not use Guided Function. The diagnosis log will not be uploaded to GFF paperless) Transport Mode Deactivation, DTC check, set service reminder *It is advised to start ODIS with the engine running to enable all 5F Test Plans in GFF and also to ensure SVM sees all control units during the SVM check vehicle configuration Deactivate vehicle transport mode (via Special functions –> Service work –> 19-Transport mode activating/deactivating ) Set service reminder (via Special functions –> Service work –> 17-PDI-resetting SRI at PDI, counter reset, etc.) Under the Hood Fluid Check and Inspection Check all fluid levels and top off if necessary Check engine oil level using Special Tool T40178 on a flat and level surface Trunk Inspection Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit behind spare tire. Please note that in the hybrid it is located on the luggage floor on the right side Verify operation of luggage cover Exterior Test windshield washers (front and rear) for aim and function Turn on headlights and test headlamp washers (if equipped) Test exterior lighting functions Install the rubber strips to the top of the base carrier bars (do not install the carrier bars on the vehicle unless customer has requested). Repackage the bars into the box if they are not being installed on the vehicle Retrieve the paper with the torque wrench key code from the base carrier bar box. Insert the paper with the key code into the owner’s literature wallet. Record torque wrench key code in the VDF to ensure it’s documented in the event the paper with the code is misplaced Check key functionality, including seat memory (if equipped); verify vehicle starts and runs with the start/stop button; verify all doors lock/unlock with remote and advanced key, including all door handle sensors with the advanced key (if equipped) Interior For MMI3G+ vehicles, set adaptation channel (via Special functions –> Service work –> : 5F–Activating/deactivating storage of music). Also referred to as CD Ripping. Perform hard reset of the MMI to complete the activation Check operation of all switches: Locks, windows, seat adjustment, seat heating (if equipped) and child safety features Perform an SVM specified /actual comparison (via Special functions ->Software Version Management (SVM)) Verify operation of all interior lights Perform any campaign update requiring SVM at this time (follow instructions listed in campaign documentation) Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Mirrors: Inspect folding, adjustments, RH tilt in reverse, and memory (if equipped) Inspect operation of lighter, aux. outlet under armrest, and rear outlet and cargo area (if equipped) Verify operation of all front and rear seat belts and latches Effective 4-28-2014-US Version 1.0 1 of 3 PERFECT DELIVERY INSPECTION (PDI) 2015 Q5/Q5 hybrid/SQ5/Q5 TDI | Audi Technician Report Interior (continued) Audi connect (if equipped) (USA ONLY) Check horn operation Verify Audi connect Information Packet is present, including Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile Terms & Conditions (T&C) (if applicable) Check sunroof and sunshade operation (open/close/vent/ deflector at edge) Passenger side airbag: Verify operation of Passenger Occupant Detection System Start-Stop-System info (if applicable): Verify the velum sticker is on the start/stop button. Remove the Start-Stop-System information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi Radio Connect the dealer demo SIM card to the vehicle and make sure the system fully connects to 2G or 3G (2G or 3G symbol with Box surrounding it)(only applies if in a T-Mobile service area) Enable Google Earth in the navigation settings and verify the white Google Logo appears next to the 2G or 3G symbol Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active > select “Visible”) Verify operation of AMI or aux. input (if equipped) Check Wi-Fi hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system. SD card slot: Insert SD card and test function (Test all SD card slots as equipped) On-Hoist Inspection Verify HD Radio is turned “off” in Radio/Settings Menu Check underside of vehicle for fluid leaks and loose components Audi MMI/Navigation Check steering, boots, brake system, hoses, tires and wheels for damage Verify and set Language and Measurement Units in Setup Menu Remove transport suspension blocks (if installed) Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location Inspect wheel bolts for proper torque using torque wrench Verify operation of CD player Navigation (if equipped): Set dealership location (for following back to dealership during road test) Set the “Music volume while parking” to 6 lines (accessed via MMI rear view camera display: Settings > Music volume while parking) (applies to vehicles with park assist or rear view camera) Voice Activation (if equipped): Press the “Talk” button and verify several Commands Onboard Video Tutorials Load Onboard Video Tutorials Turn ignition on Insert the Onboard DVD into the DVD Drive Select the CAR function button. System will initialize Select the Owner’s Man. function by selecting the upper right control button Select “Yes” Select “CD/DVD” Select “Start update” Turn off ignition to start update (the update will take approx. 5 minutes) Install wheel bolt covers and center caps as supplied If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar doorjamb, and store tire pressure values in Car/System menu Road Test Check for squeaks, rattles and wind noise Verify operation of Audi parking system plus with rear view camera (if equipped) Verify engine performance and acceleration EV button: Push the EV button at a speed below 65 mph and check for lights on EV button and instrument cluster. EV mode may or may not activate based on current operational criteria as described in the owner’s manual Check MMI and instrument cluster for proper operation mode indication (green lights while EV or electrical drive, orange while combustion engine active, etc.) Check for state of charging increasing while braking within recuperation range (see power meter for details) Verify transmission operation, including shift paddles (if equipped) Check steering/tire alignment Once completed, remove the disk and place back into the case for the next vehicle Effective 4-28-2014-US Version 1.0 2 of 3 PERFECT DELIVERY INSPECTION (PDI) 2015 Q5/Q5 hybrid/SQ5/Q5 TDI | Audi Technician Report Road Test (continued) Post-Road Test Inspection Test drive vehicle applying brakes several times (at least 4 times) at 20 mph (32 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation Interrogate fault memory using the Scan Tool and print Diagnostic Log Parking brake: Apply and verify hold and release Verify quality of radio reception in AM/FM/SAT bands Record final mileage on checklist and sign checklist Ensure the yellow tire pressure tag is installed on steering wheel Verify cruise control/ACC (if equipped) functions Verify Audi side assist functionality (if equipped) Showroom Display/Inventory Storage/Demo Vehicle Climate control: Check all functions and ensure proper A/C cooling Install showroom charger to ensure battery remains charged at all times Seat heating/ventilation (if equipped): Inspect for proper operation Apply Inventory Maintenance Sticker Install standard wiper blades (if not already installed) Navigation function (if equipped): Activate NAV and follow directions back to dealership Technician I certify that all operations have been completed and this vehicle has been prepared in accordance with Audi Procedures and Quality Standards, and has met the standards for Perfect Delivery. Last 8 of VIN Effective 4-28-2014-US Version 1.0 Technician Signature Completion Date 3 of 3