A9723012069999_3
Service Bulletin Details
Public Details for: A9723012069999_3
This bulletin provides information when the vehicle does not start and the warning "engine/power unit start system: fault" is visible; dtc B114815 is stored.
Models from 2024
2024 AUDI A3 |
2024 AUDI RS3 |
2024 AUDI S3 |
Models from 2023
2023 AUDI A3 |
2023 AUDI RS3 |
2023 AUDI S3 |
Models from 2022
2022 AUDI A3 |
2022 AUDI RS3 |
2022 AUDI S3 |
Technical Service Bulletin 97 Vehicle does not start; warning in cluster "Engine/power unit start system: fault". DTC B114815 is stored 97 23 01 2069999/3 October 16, 2023. Supersedes Technical Service Bulletin Group 97 number 23-99 dated August 25, 2023, for reasons listed below. Model(s) Year VIN Range Vehicle-Specific Equipment All Not Applicable A3, S3, and RS 3 2022 – 2024 Condition REVISION HISTORY Revision Date Purpose 3 - Revised Service ( Added headlight aiming step) Revised Warranty (Updated labor operations) 2 08/25/2023 Revised Service (Updated SVM table and content) Revised Condition (Added DTCs) Revised Warranty (Added SW update, removed part replacement) 1 04/17/2023 Initial publication Customer states: The vehicle does not start. The message “Engine start system: fault” or “Power unit start system: fault” appears in the instrument cluster. Workshop findings: The following DTC is stored statically or intermittently in the onboard supply control, J519 (address word 0009): • DTC B114815: Terminal 15 open circuit/short circuit to B+ There may also be related terminal 15 implausible DTCs stored in various modules. Please review the table below. Diagnostic address DTC 0003 U140500 Terminal 15, implausible signal 0015 B201C00 Supply voltage implausible signal 0023 C121E00 Terminal 15, implausible signal © 2023 Audi of America, Inc. Page 1 of 4 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 0044 U112300 Data bus error value received 0069 U140500 Terminal 15, implausible signal 0075 U112300 Data bus error value received Technical Background Hardware conflict within the onboard supply control, -J519- (address word 0009). Production Solution Not applicable. Service If the customer concern and DTC match as stated above, update onboard supply control unit -J519- (address word 0009) using SVM code 09A059. Please reference the TSB number in the claim comments. SVM Update Instructions Always use DoIP when flashing a control module via ODIS in supported vehicles. To Activate DoIP, select Administration>>General>>GFF Process>>DoIP communication>>Only allow DoIP communication This setting will automatically reset when the diagnostic session is ended. You can tell if DoIP is active by observing a red LED on the VAS 6154(A) 1. Follow all instructions in TSB 2011732: 00 Software Version Management (SVM), operating instructions. 2. Update the onboard supply control unit -J519- (diagnostic address 0009) using the SVM action code as listed in the table below, if necessary: Old module software part number Old SW Version Old Target Data New Target Data New Container Version Container Number Software Version (or higher) SVM Code Input (or higher) 5WA937086** 0174 0182 Any 5WA937087** 0174 0182 Any © 2023 Audi of America, Inc. * 0183 09A059 Page 2 of 4 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 3. Aim both headlight assemblies. Warranty Claim Type: • 110 Up to 48 Months/50,000 Miles. • G10 for CPO Covered Vehicles – Verify Owner. • If the vehicle is outside of any warranty, this Technical Service Bulletin is informational only. Service Number: 9710 Damage Code: 0039 Labor Operations: Update software in onboard supply control unit J519 (address word 0009) 0151 0000 Time stated on the diagnostic protocol (Max 100 TU) Adjust 2 headlights 9415 16XX See SRT with associated labor operations GFF No allowance 0 TU Diagnostic Time: (Included above) Claim Comment: Road test prior to the service procedure No allowance 0 TU Road test after the service procedure No allowance 0 TU As per TSB 2069999/3 All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty. Required Parts and Tools Tool Number Tool Description VAS 6160/VAS 6150 VAS tester with the current version of ODIS (Windows 10) Additional Information © 2023 Audi of America, Inc. Page 3 of 4 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin All part and service references provided in this TSB (2069999) are subject to change and/or removal. Always check with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the Repair Manual for fasteners, bolts, nuts, and screws that require replacement during the repair. ©2023 Audi of America, Inc. All rights reserved. The information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. © 2023 Audi of America, Inc. Page 4 of 4 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.