No. 105-23

Service Bulletin Details

Public Details for: No. 105-23

Technical information on wpj7 - rerouting wiring harness in transmission


- 2023 - 2022 -

Service
Technical Information
105/23 ENU
WPJ7
3
WPJ7 - Re-Routing Wiring Harness in Transmission (Workshop Campaign)
Vehicle Type:
991 GT3 (992) / 991 GT3 Touring (992) / 991 GT3 RS (992)
Model Year:
As of 2022 up to 2023
Concerns:
Wire harness in transmission
Cause:
There is a possibility that the wire harness in the transmission was not routed according to
specifications on the affected vehicles.
If this is the case, damage to the line insulation cannot be ruled out over the service life of the vehicle. As
a result, a yellow warning message “Transmission faulty – reverse gear not available” would be displayed
on the instrument cluster. A reduced onward trip would also be possible in the event of an error.
Action:
Re-route wire harness in transmission.
Installation
Position:
Installation position
AfterSales
Oct 13, 2023
Page 1 of 6
3
Service
Affected
Vehicles:
Technical Information
ENU 105/23
WPJ7
Only vehicles assigned to the campaign (see also PCSS Vehicle Information).
Required parts and materials
Parts Info:
Material:
Part No.
Designation
− Location
Number
PAF009388
 Countersunk screw with internal serration,
M6 x 25
− ATF oil pan on transmission
13 pieces
9P1321359
 Oil pan
– ATF oil pan
1 piece
PAF008528
 Screw plug with sealing ring M18 x 1.5
– ATF screw plug
1 piece
PAF910423
 All-round screw lens head screw M6 x 16
– Bottom rear screws for spoiler (diffuser)
5 pieces
Part No.
Designation
− Location
Number
00004330513
 Transmission oil for double-clutch transmission
oil PENTOSIN FFL 3 1.0 Ltr.
– Transmission oil
approx. 5 liter/
1.32 gal
Required tools
Tools:
•
•
•
•
Torque wrench, 2–100 Nm (1.5–74 ftlb.), e.g. 9768 - Electronic torque wrench, 2–100 Nm
(1.5–74 ftlb.)
VAS 6563 - Manual metering pumps, Porsche set
P90999 - PIWIS Tester 4
9453 - Access ramps
Preparatory work
Work Procedure: 1
2
Oct 13, 2023
Page 2 of 6
Remove support plate.
 Workshop Manual '421419 Removing and installing support plate'
Drain ATF (hydraulic oil).
For procedure, see:  Workshop Manual '370255 Replace ATF (hydraulic oil)'
AfterSales
Service
Technical Information
3
105/23 ENU
WPJ7
3
Remove ATF pan.
 Workshop Manual '375519 Removing and installing ATF pan'
Re-routing wire harness in transmission
Work Procedure: 1
Loosen transmission control unit  Screw connection for transmission control unit -A-.
Screw connection for transmission control unit
1.1
2
 Screw connection for transmission control unit -1 to 20-Loosen screws but do not
unscrew them in order to loosen the potentially clamped wire harness and then be able to
re-route it.
Remove wire harness  Transmission wire harness -1- under the plug contacts  Transmission
wire harness -2- and  Transmission wire harness -2- re-route between the plug contacts  Transmission wire harness -3- and the transmission housing.  Transmission wire harness
AfterSales
Oct 13, 2023
Page 3 of 6
3
Service
Technical Information
ENU 105/23
WPJ7
Transmission wire harness
3
Oct 13, 2023
Page 4 of 6
Fasten transmission control unit  Screw connection for transmission control unit -A-.
AfterSales
Service
Technical Information
105/23 ENU
WPJ7
3
Screw connection for transmission control unit
3.1
Fasten screws  Screw connection for transmission control unit -1 to 20- by hand and
observe tightening sequence  Screw connection for transmission control unit -1 to 20initial tightening 1.5 Nm (1.1 ftlb.) and final tightening 8 Nm (5.9 ftlb.).
Follow-up actions
Work Procedure: 1
2
3
Install ATF pan.
 Workshop Manual '375519 Removing and installing ATF pan'
Fill up ATF (hydraulic oil).
For procedure, see:  Workshop Manual '370255 Replace ATF (hydraulic oil)'
Checking and topping up ATF (hydraulic oil).
 Workshop Manual '370235 Checking and topping up ATF (hydraulic oil)'
4
Installing support plate.
 Workshop Manual '421419 Removing and installing support plate'
5
Enter the campaign in the Warranty and Maintenance logbook.
AfterSales
Oct 13, 2023
Page 5 of 6
3
Service
WPJ7
Technical Information
ENU 105/23
Warranty processing
Information
The specified labor time was determined specifically for carrying out this campaign and includes all
required preliminary work and rework. The labor time may differ from the working times published in the
Labor Times in the PCSS.
Scope 1:
Re-routing wire harness in transmission
Labor time:
Labor time: 267 TU
Re-routing wire harness in transmission
Includes:
Removing and installing support plate
Drain and fill ATF (hydraulic oil)
Removing and installing ATF pan
Required parts:
PAF009388
Countersunk screw with internal serration, M6 x 25
13 pieces
9P1321359
Oil pan
1 piece
PAF008528
Screw plug with sealing ring M18 x 1.5
1 piece
PAF910423
All-round screw lens head screw M6 x 16
5 pieces
00004330513
Transmission oil for double-clutch transmission oil
PENTOSIN FFL 3 1.0 Ltr.
approx. 5 liter/ 1.32 gal
 Damage number WPJ7 066 000 1
Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a
discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed.
© 2023 Porsche Cars North America, Inc.
Oct 13, 2023
Page 6 of 6
AfterSales


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.