PIT6044E
Service Bulletin Details
Public Details for: PIT6044E
This preliminary information communicates that a software update is in the works and to disconnect the 12 volt battery to clear the codes.
Models from 2024
2024 CADILLAC LYRIQ |
2024 GMC HUMMER EV |
Models from 2022
2022 GMC HUMMER EV |
Bulletin No.: PIT6044E Published date: 10/30/2023 Preliminary Information PIT6044E Service High Voltage with MIL and/or DTCs Models Brand: Model: Model Years: VIN: from to Engine: Transmissions: BrightDrop Zevo 600 eLCV 2023 ALL All All All Cadillac EV LYRIQ 2023 - 2024 ALL All All All GMC HUMMER EV 2022 - 2024 ALL All All All GMC HUMMER EV SUV 2024 ALL All All All Involved Region or Country North America Condition Some customers may comment the MIL is illuminated or Service High Voltage Message displayed on the IPC. A technician may nd any of the following DTCs; U2220, U2221, U2222, U2223, U2224, U2225, U2226, U2227, U2228, U2229, U222A, U222B, U222C, U222D, U222E, U222F, U2230, U2231, U2232, U2233, U2234, U2235, U2236, U2237, and/or U2C11 set as current or history. Cause A potential software anomaly may be present that will be xed in a future OTA update. Correction: Note: Updated Software and Calibrations will be released at a later date in the form of an OTA update or Service programming. Please inform the customer to accept any future OTA updates for their vehicle. This PI is not applicable if the following software and calibration P/N(s) are currently in the vehicle. K16 BECM - Identi cation Information. 2023 LYRIQ pAWD: Application Software Part Number 1: 24058918 Calibration Part Number 1: 24060149 RWD: Application Software Part Number 1: 24058917 Calibration Part Number 1: 24060146 2024 LYRIQ This PI is not applicable if the following software and calibration P/N(s) are currently in the vehicle. K16 BECM - Identi cation Information. Application Software Part Number 1: 24058918 Calibration Part Number 1: 24059907, 24059908, 24059909, 2405910 24059912, or 24059913 2024 This PI is not applicable if the following software and calibration P/N(s) are currently in the vehicle. HUMMER EV K16 BECM – Identi cation Information. & SUV Application Software Part Number 1: 24060536 Calibration Part Number 1: 24060941, 24060942, 24060943, 24060944, 24060945, 24060946, 24060947, 24060948, 24060949, 24060950, 24060951, 24060952, 24060953, or 24060954 This PI is not applicable if the following software and calibration P/N(s) are currently in the vehicle. K16 BECM – Identi cation Information. 2023 HUMMER EV Application Software Part Number 1: 24060266 Calibration Part Number 1: 24060629, 24060632, 24060633, or 24060634 2023 BrightDrop Zevo 600 This PI is not applicable if the following software and calibration P/N(s) are currently in the vehicle. K16 BECM – Identi cation Information. Application Software Part Number 1: 24056969 Calibration Part Number 1: 24060635 1. Verify the vehicle has one or more of the following DTCs set; U2220, U2221, U2222, U2223, U2224, U2225, U2226, U2227, U2228, U2229, U222A, U222B, U222C, U222D, U222E, U222F, U2230, U2231, U2232, U2233, U2234, U2235, U2236, U2237, and/or U2C11 set as current or history. Note: If all Loss of Communication DTCs are set U2220-U2237 as current or history (depending on vehicle application), do not continue with the procedure. Please start a TAC case and reference this P.I. 2. Perform the Battery Negative Cable Disconnection and Connection procedure outlined in Service Information. Warning: Always ensure the Battery Maintenance Mode is inactive before disconnecting the 12volt battery. This mode can be active with the ignition o , regardless of whether the vehicle charging cord is plugged in or not. When this mode is active, the on-board high voltage battery charger will energize the 12-volt battery cables and charge the 12-volt battery. Disconnecting the battery cables while this mode is active may result in an electrical shock or a burn from hot battery cable leads. 3. Wait 15 mins, then reconnect the 12v following the Battery Negative Cable Disconnection and Connection procedure outlined in Service Information. 4. Place the vehicle in Propulsion “Ready” mode, then turn the vehicle “OFF” and remove the keyless transmitter from the vehicle and place the transmitter in a safe location approximately 10 ft away. Wait 15 mins. Perform this two times. 5. Place the vehicle in Service mode and use GDS2 and clear all DTCs. If any of the following DTCs: U2220, U2221, U2222, U2223, U2224, U2225, U2226, U2227, U2228, U2229, U222A, U222B, U222C, U222D, U222E, U222F U2230, U2231, U2232, U2233, U2234, U2235, U2236, U2237, and/or U2C11 return, start a TAC case, and reference this P.I. 6. After completing steps 1-5 above, program the K16 BECM (Battery Energy Control Module) as outlined in Service Information. 7. After programming the BECM, perform the Battery Negative Cable Disconnection and Connection procedure outlined in Service Information / steps 2 & 3 above 1 time. 8. Verify no DTCs are set. If any of the following DTCs: U2220, U2221, U2222, U2223, U2224, U2225, U2226, U2227, U2228, U2229, U222A, U222B, U222C, U222D, U222E, U222F U2230, U2231, U2232, U2233, U2234, U2235, U2236, U2C11 and/or U2237 return, start a TAC case, and reference this P.I. Warranty Information For vehicles repaired under the Bumper-to-Bumper coverage (Canada Base Warranty coverage), use the following labor operation. Reference the Applicable Warranties section of Investigate Vehicle History (IVH) for coverage information. Labor Operation 5080388 Add Time (as Required) Description Hybrid/Electric Vehicle Battery Pack Communication Module manual reset K16 Battery Energy Control Module Program *This is a unique Labor Operation for Bulletin use only Version History Version Modi ed 5 08/03/2023 - Created on. Labor Time 1.5 Hr. 0.4 Hr. 08/09/2023 - Updated to include U2C11 09/01/2023 - Updated to add more information for the LYRIQ 09/05/2023 - Update more programming numbers for 2024 LYRIQ 10/26/2023 - Update information for BrightDrop and HUMMER EV 10/30/2023 - Updated correction. © 2023 General Motors. All Rights Reserved.