130601003C
Service Bulletin Details
Public Details for: 130601003C
Excessive oil consumption ? Perform oil consumption test and/or install piston and piston ring kit
File in Section: Bulletin No.: Service Bulletin Date: 06 - Engine 13-06-01-003C September, 2013 TECHNICAL Subject: Excessive Oil Consumption – Perform Oil Consumption Test and/or Install Piston and Piston Ring Kit Models: 2010-2013 Buick LaCrosse 2011-2013 Buick Regal 2010-2013 Chevrolet Equinox 2010-2013 GMC Terrain Equipped with 2.4L Engine (RPOs LAF, LEA) This bulletin has been revised to update the Warranty Information. Please discard Corporate Bulletin Number 13-06-01-003B. Condition Some customers may comment on excessive oil consumption and/or that they have to add oil between oil changes. Correction For this condition, technicians should perform an oil consumption test by following the latest version of Corporate Bulletin Number 01-06-01-011. Before starting the oil consumption test, verify the ECM has latest TIS2web calibrations to adjust the engine oil life monitor to a maximum of 7,500 miles (12,070 km) — Refer to Customer Satisfaction Bulletin #12312. Inspect for any obvious oil leaks that may explain the oil consumption concern and repair as necessary. Important: When checking the oil level with the oil dipstick design shown below, please note that the oil volume per notch is not linear due to the shape of the block. The upper notches (relative to the top of the handle) equal 0.24 quart (0.227 L) between each notch while the lower notches only equal 0.14 quart (0.132 L) between each notch. As a result, no oil will appear on the dipstick if it is low on oil by approximately 1.25 quarts (1.18 L) or more. When determining the oil consumption rate, the oil volume added to return it to the starting location is the total amount of oil consumed. The consumption rate must be documented on a repair order. Notice: Do not add too much oil. An overfill can lead to burn off of the excess oil. Advise the customer to wait until the oil is below the cross-hatched area at the tip of the dipstick before adding oil. Copyright 2013 General Motors LLC. All Rights Reserved. 3339530 If the oil consumption test indicates that the rate of consumption is greater than 1 quart (0.946 L) of oil every 2,000 miles (3,200 km), note the oil consumption rate, the date that the ECM was reprogrammed and any repairs/diagnosis that you have performed. The repair is to replace the pistons and rings. In some cases the bore surface may not have a uniform look to the finish (zebra stripes) as shown below. As a result, some technicians may question whether the engine should be repaired or replaced. After careful evaluation, GM Powertrain has determined that the new pistons and rings will perform correctly in bores that have this appearance so engine replacement should not be necessary. The cylinder bores do not need any machine or honing work performed on them. Refer to the picture below for acceptable surface finishes. Page 2 September, 2013 Important: DO NOT use any abrasive wheels/ materials to clean any mating surfaces. Only Plastic scrapers should be used. Please refer to the latest version of Corporate Bulletin Number 00-06-01-012. Bulletin No.: 13-06-01-003C Note: Returned oil consumption engines have been reviewed at engine tear down. It has been determined that these components do not need to be replaced: Acceptable Cylinder that Does Not Appear Uniform (Zebra Stripes) 3409678 • 3339531 While performing this repair on 2010 and 2011 vehicles built before March of 2011, it should be verified that the high pressure fuel pump (P/N 12641847), balance chain (P/N 12645237), balance chain tensioner (P/N 12649233), and timing chain kit (P/N 12635447) have been installed in this engine in a previous repair. Refer to IVH and check the parts listed in the prior repairs. If these parts have not been installed, they should be replaced at the time that the piston and rings are replaced. If they have been replaced, do not replace them again. Engines in 2012 and 2013 vehicles do not need the balance chain or fuel pump inspected. Also when performing this repair, several other parts should be inspected for excessive wear and/or damage and replaced if necessary: – Balance chain guides – Timing chain guides Important: DO NOT use any abrasive wheels/ materials to clean any mating surfaces. Only Plastic scrapers should be used. Please refer to the latest version of Corporate Bulletin Number 00-06-01-012. Camshafts and roller follower will have wear markings. This is normal and do not need to be replaced (refer to picture above). 3409680 • • Valves stems may have deposits build up on them. These deposits are characteristic of a direct inject engine. The valves stems do not need to be cleaned as they are not affecting engine performance (Refer to picture above). The oil pump does not need to be replaced as the low oil level operation did not damage the pump. Bulletin No.: 13-06-01-003C • September, 2013 The camshaft actuators do not need to be replaced at this time. The vehicle may have arrived with the engine knocking. If the oil level was 1 1/2 - 2 quarts low, it was the lack of oil causing the actuator noise. • Rod bearings can be reused if there is not any excessive scoring. Some light wear marks are acceptable. Important: Rod bearings must be marked to identify the proper location to ensure bearings are returned to their original positions. The final step is to verify that ECM OLM calibration has been installed before the vehicle is returned to the customer. Important: DO NOT use any abrasive wheels/ materials to clean any mating surfaces. Only Plastic scrapers should be used. Please refer to the latest version of Corporate Bulletin Number 00-06-01-012. Parts Information Page 3 Warranty Information For vehicles repaired under warranty, use: Labor Operation Description Labor Time 4080008* Oil Consumption Test Setup 0.2 hr Add Piston, Connecting Rod and Bearing Replacement 9.3 hrs Add To Replace Fuel Pump (2010-2011 Models Built Prior to March 2011 Only) 0.7 hr Add To Replace Balance Shaft Chain and Tensioner (2010-2011 Models Built Prior to March 2011 Only) 0.8 hr Add To Replace Timing Chain (2010-2011 Models Built Prior to March 2011 Only) 0.5 hr *This is a unique labor operation for bulletin use only. It will not be published in the Labor Time Guide. Part Number Description 12646457 PISTON KIT, ENG 12659419 RING KIT, PSTN 12637166 GASKET KIT, CYL HD 12609291 SEAL, CM/SHF GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION