24607601
Service Bulletin Details
Public Details for: 24607601
Checking and sealing water leak at lidar cover
- 2023 -
Models from 2023
2023 FARADAY FUTURE FF-91 ALLIANCE |
Faraday Future Eco Sales Co. LLC DBA Faraday Future 501 W. 190th Street Gardena, CA 90248 TSB-24-60-76-01 1/31/2024 Technical Service Campaign PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE CAMPAIGN ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN FOR MAINTENANCE OR REPAIRS. Service Campaign: Checking and Sealing Water Leak at LIDAR Cover YEAR/ MODEL 2023 MOBILE REPAIR Faraday Future Yes ☐ FF 91 2.0 Alliance No ☒ SITUATION Water leaking into cabin around the rearview mirror area and front header trim. CAUSE Urethane application during manufacturing process to seal LIDAR cap to roof glass carrier. CORRECTION Test to confirm leak and, if necessary, apply Urethane sealant around LIDAR cover area. AFFECTED VEHICLES 7G090AMR6PH000001 7G090AMR8PH000002 7G090AMRXPH000003 7G090AMR1PH000004 7G090AMR3PH000005 7G090AMR5PH000006 7G090AMR7PH000007 7G090AMR7PH000349 7G090AMR7PH000009 7G090AMR7PH000010 TSB-24-60-76-01 Faraday Future Eco Sales Co. LLC DBA Faraday Future 501 W. 190th Street Gardena, CA 90248 PROCEDURE A). Check for water leak in LIDAR mounting area NOTE: Use of a trim removal tool must be used to prevent damage during this procedure. 1. Remove Header Trim panel: 2. Disconnect harness connectors from upper header console / Header Trim: TSB-24-60-76-01 Faraday Future Eco Sales Co. LLC DBA Faraday Future 501 W. 190th Street Gardena, CA 90248 3. Run a consistent flow and volume of water to ensure complete water immersion around LIDAR cover mounting area. TSB-24-60-76-01 Faraday Future Eco Sales Co. LLC DBA Faraday Future 501 W. 190th Street Gardena, CA 90248 4. Check inside cabin for water leaks around LIDAR area shown below: B). Procedure to seal LIDAR cover 5. Once leak path is confirmed orignating from the LIDAR seal area, thorougly dry the exterior area around LIDAR cover. 6. Tape/Mask around LIDAR cap opening area to prevent urethane overflow onto surrounding parts (LIDAR cover and roof glass) keeping the cover to roof joint exposed (see Parts Information). TSB-24-60-76-01 Faraday Future Eco Sales Co. LLC DBA Faraday Future 501 W. 190th Street Gardena, CA 90248 7. Lay a thin bead of Urethane sealant in the LIDAR cover to roof glass seam to ensure a watertight joint. 8. Remove tape before Urethane sets. Allow 24 hours to dry. 9. Repeat water test (outlined above) after 24 hours to ensure area has been 100% sealed. 10. If there are no leaks, re-install interior Header trim. Header trim clips are reusable if not damaged during removal. PARTS INFORMATION Order the Part Number for your specific vehicle: Part Number Sublet Sublet Description Windo-Weld 08609 - Black - Cartridge - 10.5 fl oz Frog tape (Green or Blue) - 0.94" Wide – roll Quantity 1 1 CLAIM INFORMATION Covered under the terms of the Faraday Future New Vehicle Limited Warranty for Passenger Cars. Defect Code 60761302 LIDAR Water Leak Campaign Refer to Aftersales Portal for the corresponding flat rate unit allowances. Labor Operation Code Description Labor Allowance 60760117 Check for water leak around LIDAR cover 1.5 hr 60760149 Reseal Lidar cover to roof mounting and recheck for leaks 4.0 hr TSB-24-60-76-01