ReportN

PERFECT DELIVERY INSPECTION (PDI)
2015
A5, S5, and RS5 Cabriolet
Audi Technician Report
Stock No.
Dealer Number
R.O. No.
VIN
Road test mileage out
Road test mileage in
All items must be completed prior to customer delivery by an Audi
technician
**Refer to the Special functions tab of ODIS Diagnosis using GFF
for the PDI function tests
**Audi recommends using an Audi approved battery charger to
prevent excessive battery discharge during inspection
Trunk Inspection
 Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit behind right side
cover
 Set spare tire pressure
 Verify trunk operation, including emergency release handle
Open Campaigns/Updates
Exterior
 Check Elsa for open campaigns and updates. Perform
campaigns not requiring SVM if applicable. Campaigns
requiring SVM should only be performed after the vehicle has
been taken out of transport mode
 Test windshield washers for aim and function
Battery Inspection
 Check battery clamps for proper torque. Re-torque if required
 Perform the A-battery test for new batteries using GFF in ODIS
Diagnosis –> Special functions –> Service work. Select option 2,
the battery test for new batteries as part of the pre–delivery
inspection and act according to the test result (ok, recharge,
replace). Ensure diagnosis log is uploaded to the GFF paperless
server by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided
Function. The diagnosis log will not be uploaded to GFF paperless)
Transport Mode Deactivation, DTC check, set service reminder
*It is advised to start ODIS with the engine running to enable all
5F Test Plans in GFF and also to ensure SVM sees all control units
during the SVM check vehicle configuration
 Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
 Set service reminder (via Special functions –> Service work –>
17-PDI-resetting SRI at PDI, counter reset, etc.)
 Turn on headlights and test headlamp washers (if equipped)
 Test exterior lighting functions
 Check key functionality including seat memory (if applicable);
verify vehicle starts and runs with the start/stop button; verify
all doors lock/unlock with remote and Advanced Key, including
door handle sensors (if equipped)
Interior
 Check operation of all switches: Locks, windows, seat adjustment, and child safety features
 Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
 Verify operation of all interior lights
 Mirrors: Inspect folding, adjustments, RH tilt in reverse, and
memory (if equipped)
 Inspect operation of lighter, aux. outlet under armrest and rear
outlet
 Verify operation of all front and rear seat belts and latches
 Check horn operation
 Passenger side airbag: Verify operation of Passenger Occupant
Detection System
 Verify convertible top manual closing tools are present
 For MMI3G+ vehicles, set adaptation channel (via Special
functions –> Service work –> : 5F–Activating/deactivating
storage of music). Also referred to as CD Ripping. Perform hard
reset of the MMI to complete the activation
Radio
 Perform any campaign update requiring SVM at this time
(follow instructions listed in campaign documentation)
 SD card slot: Insert SD card and test function (Test all SD card
slots as equipped)
 Verify operation of CD player
 Verify operation of AMI or aux. input (if equipped)
 Verify HD Radio is turned “off” in Radio/Settings Menu
Under the Hood Fluid Check and Inspection
Audi MMI/Navigation
 Check all fluid levels and top off if necessary
 Verify and set language and Measurement Units in Setup Menu
 Check engine oil level using Special Tool T40178 on a flat and
level surface
 Set Time source setting to “GPS” and set Auto daylight savings
time to “on.” Change time zone to the appropriate dealer
location
Effective 8-19-2014-US
Version 1.2
1 of 2
PERFECT DELIVERY INSPECTION (PDI)
2015 A5, S5 and RS 5 Cabriolet | Audi Technician Report
Audi MMI/Navigation (continued)
On-Hoist Inspection (continued)
 Navigation mode (if equipped): Set dealership location (for
following back to dealership during road test)
 If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum
recommended tire pressures listed on the B-pillar doorjamb,
and store tire pressure values in Car/System menu
Onboard Video Tutorials (USA ONLY)
 Load Onboard Video Tutorials
Road Test
 Turn ignition on
 Insert the Onboard DVD into the DVD Drive
 Select the CAR function button. System will initialize
 Select the Owner’s Man. function by selecting the upper right
control button
 Check for squeaks, rattles and wind noise
 With engine running to conserve battery power, test folding
power top
 Verify engine performance and acceleration
 Test operation of folding power top (Cabriolet)
 Select “Yes”
 Verify operation of rear view camera and rear parking sensors
(if equipped)
 Select “CD/DVD”
 Select “Start update”
 Turn off ignition to start update (the update will take approx. 5
minutes)
 Once completed, remove the disk and place back into the case
for the next vehicle
Audi connect (USA ONLY) (if equipped)
 Verify Audi connect Information Packet is present, including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile
Terms & Conditions (T&C) (if applicable)
 Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with arrows)(only applies if in a T-Mobile service area)
 Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
 Ensure the wireless network is turned on (TEL function button
> Settings Ctrl button > Wi-Fi settings > Wi-Fi active > select
“Visible”)
 Verify Audi side assist functionality (if equipped)
 Verify Audi active lane assist functionality (if equipped)
 Verify transmission operation including shift paddles
 Check steering/tire alignment
 Test drive vehicle applying brakes at least 4 times at 20 mph
(35 km/h) to clean brake rotors. Check for abnormal noise/
vibration/pulsation
 Parking brake: Apply and verify hold and release
 Verify quality of radio reception in AM/FM/SAT bands
 Verify cruise control/ACC functionality (if equipped)
 Verify functionality of heated/ventilated seats and neck-level
heating system (if equipped)
 Climate control: Verify all functions and ensure proper A/C
cooling
 Navigation function (if equipped): Activate NAV and follow
directions back to dealership
 Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits
of VIN that are automatically preset in the system
Post-Road Test Inspection
On-Hoist Inspection
 Record final mileage on checklist and sign checklist
 Check vehicle underside for fluid leaks and loose components
 Ensure the yellow tire pressure tag is installed on steering
wheel
 Interrogate fault memory using using Scan Tool and print
Diagnostic Log
 Check steering, boots, brake system, hoses, tires and wheels
for damage
If Vehicle is for Showroom Display/Inventory Storage or Demo Use
 Remove transport suspension blocks (Please follow ELSA
instruction)
 Install showroom charger to ensure battery remains charged at
all times
 Inspect wheel bolts for proper torque using torque wrench
 Apply Inventory Maintenance Sticker
 Install wheel bolt covers and center caps as supplied
 Install standard wiper blades (if not already installed)
Technician
I certify that all operations have been completed and this vehicle has been prepared in accordance with Audi Procedures and
Quality Standards, and has met the standards for Perfect Delivery.
Last 8 of VIN
Effective 8-19-2014-US
Version 1.2
Technician Signature
Completion Date
2 of 2