24-01-016H
Service Bulletin Details
Public Details for: 24-01-016H
Certain hyundai vehicles may not be equipped with an engine immobilizer. This bulletin provides the service procedure to upgrade the ibu/bcm (integrated body control unit/body control module) to revise the oem hyundai burglar alarm system
- 2018 -
Models from 2018
2018 HYUNDAI ELANTRA |
GROUP NUMBER CAMPAIGN Technical Service Bulletin SUBJECT: DATE 24-01-016H MODEL(S) FEBRUARY 2024 ELANTRA (AD) IBU/BCM ANTI-THEFT SOFTWARE UPGRADE (SERVICE CAMPAIGN 9A8) IMPORTANT Dealers must perform this service campaign on all affected vehicles prior to customer retail delivery and whenever an affected vehicle is in the shop for any maintenance or repair. Access the "Vehicle Information" screen via WebDCS to identify open campaigns. Description: Certain Hyundai vehicles may not be equipped with an engine immobilizer. This bulletin provides the service procedure to upgrade the IBU/BCM (Integrated Body Control Unit/Body Control Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic. NOTICE Applicable vehicles with the previous Anti-Theft Software Upgrade under Campaign 993 will need a revised IBU/BCM Upgrade to ensure the Anti-Theft Software Upgrade meets Campaign 9A8 requirements. Applicable Vehicles: Vehicles not equipped with an engine immobilizer, and not equipped with START/STOP ignition button • Certain 2018 MY Elantra (AD) Warranty Information: MODEL OP. CODE OPERATION OP. TIME CAUSAL PART NATURE CAUSE ELANTRA (AD) SVC9A8R0 BCM/IBU UPGRADE 0.3 M/H 95400-F2AW0 I14 ZZ3 NOTE 1: Submit claim on Claim Entry Screen as "Campaign" type. NOTE 2: If a part that is not covered by this campaign is found in need of replacement while performing this campaign and the affected part is still under warranty, submit a separate claim using the same repair order. If the affected part is out of warranty, submit a Prior Approval request for goodwill consideration prior to performing the work. NOTE 3: This TSB includes Repair validation photos. Op times include VIN, Mileage, and Repair validation photo(s) as outlined in the Digital Documentation Policy. SUBJECT: IBU/BCM ANTI-THEFT SOFTWARE UPGRADE (SERVICE CAMPAIGN 9A8) Service Procedure: IBU/BCM SOFTWARE UPGRADE NOTES i Information • • Before proceeding, ensure the vehicle is not equipped with a START/STOP push button. Also, ensure the vehicle is not equipped with an immobilizer lamp on the instrument cluster when ignition is turned ON. i Information Check if the vehicle's current software version will need to be upgraded: • Check the current version of the IBU/BCM ROM ID and compare it to the ROM ID information table listed below before attempting to perform the software upgrade. i Information You must initially perform the GDS IBU/BCM Upgrade in Auto Mode. • Refer to the TSB 15-GI-001 for the tablet-based Mobile GDS ECU upgrade procedures. • If the IBU/BCM upgrade starts but then fails in Auto Mode, perform the upgrade in Manual Mode to recover. i Information • • Troubleshooting Tips If there are issues with the software upgrade or certain features not operating normally on the vehicle after the upgrade, then perform capacitive discharge and try again. If the software is upgrading and fails (not relating to GDS disconnection or battery died) at any percentage, then try the following: o Select OK when the error message pops up, and DO NOT SELECT ANYTHING ELSE, LEAVE EVERYTING AS IS. o Turn the ignition OFF for 15 seconds and then turn it back ON. o Proceed with MANUAL upgrade procedure following the GDS screen instructions. TSB #: 24-01-016H Page 2 of 4 IBU/BCM ANTI-THEFT SOFTWARE UPGRADE (SERVICE CAMPAIGN 9A8) SUBJECT: EVENT INFORMATION EVENT DESCRIPTION 933. AD(a) IMMOBILIZER (BCM) LOGIC IMPROVEMENT MODEL Elantra (AD) MANUAL MODE PASSCODE INFORMATION TABLE: MENU Elantra (AD) BCM 95400-F2AW1/BB1 (1.12, 200) ROM ID INFORMATION TABLE: MODEL MODEL BCM/IBU P/N YEAR Elantra (AD) PASSCODE 2202 ROM ID OLD NEW 95400-F2AW1 95400F2AW1_112 95400F2AW1_200 95400-F2BB1 95400F2BB1_112 95400F2BB1_200 2018 95400F2***_301 IBU/BCM SOFTWARE UPGRADE STUI This TSB includes repair validation photo(s). Refer to the latest Warranty Digital Documentation Policy for requirements. 1. Select IBU/BCM as the system to upgrade. 2. Select ID Check. Check the current version of the IBU/BCM ROM ID and compare it to the ROM ID information table listed below before attempting to perform the software upgrade. 95400F2AW1_200 95400F2***_301 3. Perform GDS software upgrade. Refer to TSB 15-GI-001 for the tablet-based Mobile GDS ECU upgrade procedures. TSB #: 24-01-016H Page 3 of 4 IBU/BCM ANTI-THEFT SOFTWARE UPGRADE (SERVICE CAMPAIGN 9A8) SUBJECT: 4. Ensure the software upgrade was successful with the latest ROM ID. 95400F2AW1_301 95400F2***_301 5. STUI Take a screenshot of the 'ECU Upgrade Complete' screen using your tablet and upload to STUI. 95400F2AW1_301 95400F2***_301 6. After the software has upgraded, check for Diagnostic Trouble Codes in the ALL menus and erase any DTC. 7. Software upgrade complete. TSB #: 24-01-016H Page 4 of 4