K0D_TIS_Technica
Service Bulletin Details
Public Details for: K0D_TIS_Technica
Ti: k0d expired on 10/31/2023. Technical instructions for limited service campaign k0d frame corrosion resistant compound (crc) application certain 2011 ? 2015 model year tacoma
- 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 -
Models from 2017
2017 TOYOTA TACOMA |
Models from 2016
2016 TOYOTA TACOMA |
Models from 2015
2015 TOYOTA TACOMA |
Models from 2014
2014 TOYOTA TACOMA |
Models from 2013
2013 TOYOTA TACOMA |
Models from 2012
2012 TOYOTA TACOMA |
Models from 2011
2011 TOYOTA TACOMA |
IMPORTANT UPDATE FOR LIMITED SERVICE CAMPAIGN K0D 20 23 TECHNICAL INSTRUCTIONS FRAME CORROSION RESISTANT COMPOUND (CRC) APPLICATION er 3 1, CERTAIN 2011 – 2015 MODEL YEAR TACOMA (2016-2017 model year instructions can be found on TIS) COLD CLIMATE STATES ONLY ob CT, DE, IL, IN, KY, MA, MD, ME, MI, MN, NH, NJ, NY, OH, PA, RI, VA, VT, WI, WV and District of Columbia O ct UPDATE 6/22/2021 Update 6/22/21 • Details about aftermarket wax instructions have been updated. on Updated 3/6/20 • Repair Type Confirmation Step has been added on page 8. • Primary filter cleaning procedure added in appendix. d Update 1/23/20 • Wand cleaning process has been added for the wand tips in the appendix re Update 1/10/20 • The Checksheet section was updated with details about aftermarket wax and Checksheet requirements pi Update 11/15/19 • Updated browser and picture size requirements for Checksheet D Ex The repair quality of covered vehicles is extremely important to Toyota. All dealership technicians performing this service campaign are required to successfully complete the most current version of the E-Learning course “Safety Recall and Service Campaign Essentials”. All Technicians will also be required to complete the ELearning Module SCK0D and FTS Instructor Led course TIR019A. To ensure that all vehicles have the repair performed correctly; technicians performing this recall repair are required to currently hold at least one of the following certification levels: K0 • Certified (any specialty) • Expert (any specialty) • Master • Master Diagnostic Technician It is the dealership’s responsibility to select technicians with the above certification level or greater to perform this service campaign repair. Carefully review your resources, the technician skill level, and ability before assigning technicians to this repair. It is important to consider technician days off and vacation schedules to ensure there are properly trained technicians available to perform this repair at all times. 1 • For a complete list of Site Selection Guidelines and, Fire, Building, and Zoning Codes information for your state, please refer to the Dealer Information Packet. Please ensure your dealership complies with all regulations set forth in this packet. • Keep records to comply with Federal/State/Local regulations and requirements. See the Federal, State & Local Requirements Guide and any Supplements to that Guide. 20 23 OPERATION FLOW CHART Verify Vehicle Eligibility 1. Confirm vehicle VIN matches the R.O. 2. Check the TIS Vehicle Inquiry System Not Covered No further action required No No further action required; these vehicles can only be sprayed at approved Toyota dealers Covered Is the vehicle located at a dealership approved to spray 712-THV-T CRC? Did the vehicle pass the ZKA Frame Inspection? O ct Perform drying and cleaning process ob Verify repair type on TIS. CRC Application Required No er 3 Yes CRC Application Not Required 1, Yes During the drying and cleaning process was perforation 10mm or larger found in the locations identified in green below? Proceed with Frame Replacement as outlined in the ZKA TI on Yes No re d Install the specific Frame Plugs outlined in the Technical Instructions K0 D Ex pi Apply the 712THV-T Internal CRC to the areas of the frame outlined in the TI Complete online check sheet Install remaining Frame Plugs and Frame Side Rail Seal Campaign completed, return the vehicle to the customer Cold Climate States include - CT, DE, IL, IN, KY, MA, MD, ME, MI, MN, NH, NJ, NY, OH, PA, RI, VA, VT, WI, WV and District of Columbia NOTE: Ensure to follow the entire procedure and perform all steps completely any deviation will be subject to warranty claim debit. NOTE: If aftermarket wax covers an area covered by K0D, CRC used in K0D should NOT be applied 2 over the top. Only apply K0D CRC in areas that are not covered by aftermarket CRC but are covered under K0D normally. Also install plugs and covers as customary in K0D. IDENTIFICATION OF AFFECTED VEHICLES 20 23 A. COVERED VIN RANGE er 3 1, NOTE: • Vehicles currently registered in the Cold Climate States* or the District of Columbia (D.C.) that do not have significant corrosion found are eligible for Corrosion-Resistant Compound (CRC) application to the frame if it did NOT previously have the frame sprayed and/or had the frame previously replaced. • Check TIS to confirm the VIN is covered in K0D. This will verify the vehicle is covered and has not already been completed prior to dealer shipment or by another dealer. • TMNA warranty will not reimburse dealers for repairs conducted on vehicles that are not covered or were completed by another dealer. * CT, D.C. , DE, IL, IN, KY, MA, MD, ME, MI, MN, NH, NJ, NY, OH, PA, RI, VA, VT, WI, & WV • If the vehicle is regular operated or registered in a cold climate state but is not included in K0D contact Quality Compliance for instructions on how to include the vehicle in K0D PREPARATION ob PARTS O ct To assist dealers in determining the correct part number(s) to order, a website has been set up to look up part numbers by VIN. Please go to https://tacoma-2011-2017-frames.imagespm.info/ select the appropriate campaign/vehicle, enter the VIN, and the correct part numbers to order will be displayed. The website is for part(s) application reference only and won’t order the parts, confirm campaign completion status, or confirm campaign applicability. on Based on the results shown in the parts look up site you will be able to determine if the vehicle needs wax application or not. Confirm what parts are listed in the site shown above before proceeding A. WAX Part Name WAX (18 Liters PAIL CAN) Qty 3.3L (Per Vehicle) K0 D Ex pi re d Part Number 00289-TS00P 3 B. SUPPORT MATERIALS Individual Parts: Part Name Qty Plug, Hole Model Year 2011-2015 (Short wheel base only) 2011-2017 90950-01A19 Plug, Hole 90950-01987 Part Name Plug Hole Kit CRC Application 1 Model Year 2011-2015 Qty 1 Parts Kits: Part Number 04008-07735 2 Qty 2 2 4 4 2 2 1 2 2 4 ob er 3 1, The kit above includes the following parts: Part Number Part Description 90950-01A24 90950-01984 90950-01987 90950-01631 Plug, Hole 90950-01990 90950-01991 90950-01931 90950-01A11 94183-00831 Nut, Lock 94611-10800 Washer, Plate 2 20 23 Part Number 04008-21104 Plug Hole Kit CRC Application 3 2011-2015 Qty 2 2 2 1 1 2 2 4 K0 D Ex pi re d on O ct The kit above includes the following parts: Part Number Part Description 90950-A1008 Plug, Hole 90950-A1009 90080-46327 Clip 5114A-04010 Seal, Frame Side Rail, RH 5114B-04010 Seal, Frame Side Rail, LH 90178-A0112 Nut, Flange 90105-A0356 Bolt, Flange 90119-A0169 Bolt w/Washer 1 4 1, er 3 *Drying Kit Includes Equipment Qty Air Mover 1 E-TES Heater 1 Air Duct Plate 1 Air Duct Plugs 2 Air Duct Hoses 2 Air Duct Adapters 2 4in Hose Clamps 4 3in Hose Clamps 2 20 23 C. STANDARD TOOLS & EQUIPMENT • Standard hand tools • Torque wrench SPECIAL EQUIPMENT The following equipment was shipped to your dealership prior to the launch of LSC K0D. Equipment Purpose Application Area Interior / Open Section Drying Equipment Kit Drying Frame Drying *There will be 2 silver colored hoses that will be included in the kit but will not be used in the campaign procedure Cleaning Interior / Open Section Frame Drying and Cleaning ob Cleaning Equipment Kit Wand Kit on O ct *Cleaning Kit Includes Equipment Qty Power Tool Wire 1 Brush Power Tool Wand 1 PVC Handle 1 Extended Wire Brush 1 2ft Air Gun 1 712THV-T Wax Application K0 D Ex pi re d *Wand Kit Includes Equipment Short Wand Long Wand LH Guide Plug RH Guide Plug Wax Application Spray 712THV-T Wax Package Application Interior Frame CRC Application. Qty 1 1 1 1 Interior Frame CRC Application. *Wax Application Spray Package Includes Equipment Qty Pump and Heater 1 Assembly TSL Bottle 1 Owner’s Manual 1 The items below were previously shipped to your dealership for previous campaign (H0F and J0M). Equipment 90o Drill Adapter Drill Bits J0M Endoscope Purpose Drill Holes Inspect Frame Application Area These tools will be used to attach the Frame Side Rail Seal. Interior Frame Sections 5 K0 D Ex pi re d on O ct ob er 3 1, 20 23 D. MATERIALS & SUPPLIES (Locally Procured by Dealer) • Wire Brush • C-Clamp • Bungee Cord / Strap • Protective eyewear • Air Coupler • Gasket Scraper • Dust mask • Appropriate NIOSH approved respirator** (Follow all Federal, State, Local Environmental, Health and Safety Requirements such as OSHA Regulations. Please refer to the SDS for details on the appropriate mask for each CRC.) Example of a NIOSHapproved respirator **NOTE: • Refer to the SDS located in the Appendix for additional information on respirator use. • It is up to the individual dealership to ensure compliance with OSHA regulations. • If you require further assistance in regards to NIOSH approved respirators, we have found 3M® to be a useful reference/source. 3M® Technical Assistance: 1-800-243-4630 3M® Customer Service: 1-800-328-1667 3M® Web Site: www.3m.com/occsafety • Protective gloves • Chemical Resistant Gloves (refer to SDS for specific type) • Masking tape • Duct tape • Plastic wrap (for storage of wands, guns and wax pail) • Shop cloth/paper towels • Garbage Bags • Paint Prep Cup (Φ 10-15cm (3.94 - 5.91 in.) for paint work. This cup will be used to check wax application.) E. SPACE 1 stall (with swing arm lift) + α (for wax application system space) 6 VEHICLE INSPECTION WORK PROCEDURE 20 23 BACKGROUND Toyota has received a number of reports regarding frame corrosion perforation on 2011 – 2017 model year Tacoma vehicles. In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle’s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment. NOTE: Vehicle frame inspection is performed under CSP ZKA, for inspection instructions go to CSP ZKA Frame Replacement Technical Instructions. ob er 3 1, • Because of variations in State and local laws, dealerships conducting K0D in certain states may require government approvals prior to starting the campaign. Depending upon the state, dealerships also may be subject to restrictions on the number of vehicles to which the CRC can be applied in any single day, week, or month. Please refer to the Dealer Information Packet and any Supplements for important information about any such approvals or restrictions that may apply to your dealership. Your dealership must adhere strictly to these requirements. • For a complete list of Site Selection Guidelines, Fire, Building, and Zoning Codes information for your state, please refer to the Dealer Information Packet as well as any Supplements. Please ensure your dealership complies with all regulations and all issued packets/instructions. OTHERS PRECAUTIONS WHEN HANDLING THE HIGH PRESSURE SYSTEMS When the spray equipment, sealer gun or the wand tips are clogged, leaking, abnormal noise, etc., please DO NOT operate the equipment and contact the following: Bosch Technical Assistance Line - 1-800-933-8335 (Option 4) Be careful as you are using the high pressure spray gun. Always follow the instructions and observe the specified pressures. NEVER operate the pressure regulators to be over the specified values. e.g. DO NOT try to blow out the wand or tip clogging by high-pressure air. It may result in splashing out wax or breaking the wand or hose, and the scattered broken parts may cause serious injuries. Make sure to check for leakage or breakage before each use. If any problems are found, stop using the system immediately and please contact the following: Bosch Technical Assistance Line - 1-800-933-8335 (Option 4) DO NOT disassemble the parts other than the short wand or the long wand. 2. PRECAUTIONS WHEN HANDLING WAX Attention should be paid as the wax is very slippery. Wipe off the wax on the floor and shoes promptly to not slip and fall. Perform work in a well-ventilated area. Always work with clean tools and hands. 3. PRECAUTIONS WHEN USING APPLICATION SYSTEM Attention should be paid to NOT get caught as the application hose is long and hard. DO NOT bend or modify hoses or piping. Pay attention to the position of the system. 4. KEEP YOUR WORK SPACE ORGANIZED DO NOT place removed parts or unused items such as wands on the floor. 5. CONTACT INFORMATION FOR TROUBLESHOOTING For any issues with the Spray Wax/Cleaning equipment contact your FTS for assistance. If your FTS is not available, contact the Bosch Technical Assistance Line - 1-800-933-8335 (Option 4) for assistance. K0 D Ex pi re d on O ct 1. 7 REPAIR TYPE CONFIRAMTION It is critical that each VIN is confirmed using TIS to determine the repair type. Certain vehicles require CRC application and parts, other vehicles require no CRC application and only needs parts. If an incorrect repair is performed, the claim will be subject to debit. 20 23 Repair Type – No CRC Application Required er 3 1, Repair Type – CRC Application Required VEHICLE PREPARATION LIFT UP THE VEHICLE Decide the center of gravity and support positions according to the repair manual on TIS. NOTE: Observe the instructions of the lift manual. When using a swing arm with a plate, set the position of the plate to the rear (set by extending the arm). Avoid the application hole. 2. REMOVE THE FRONT SUSPENSION MEMBER BRACKET (IF EQUIPPED) Remove the front suspension member bracket. K0 D Ex pi re d on O ct ob 1. 8 DRILL HOLE FOR FRAME RAIL SEAL DRILL HOLE FOR FRAME RAIL SEAL NOTE: You may not have to drill a hole as some models will already have a threaded hole for the bolt. Inspect for a threaded hole before you begin the next steps. Using Template A and B in the appendix, locate the location on both outer frame side rails. • Print the Template • Cut the template out • Align the template with the datum hole • Mark location of hole on outer frame side rail Use a center pin punch to create a dimple for the drill bit so it will not wander during drilling. Using the 90o drill adapter provided and the stepper bit, drill a 9mm (3/8”) hole in the outer frame side rail as shown. Repeat procedure for opposite side frame rail. er 3 1, 20 23 1. DRYING INITIAL SETUP (Required for initial setup only) O ct INSTALL THE AIR MOVER INTO THE E-TES HEATER a. Push the air mover into the E-TES heater. Ensure the air mover is fully seated into the E-TES heater d on 1. ob Before starting this process, review the SCK0D E-Learning Drying section for key details INSTALL THE AIR DUCT PLATE ONTO THE E-TES HEATER a. Using the 4in hose clamps, attach the air duct plugs into the ends of the air duct plate. b. Install the air duct plate to the front of the E-TES heater and secure it with a bungee cord attached around the E-TES heater K0 D Ex pi re 2. 9 20 23 ATTACH AIR DUCT HOSES TO E-TES HEATER a. Install 4in hose clamp to the air duct adapter. Do this to both air duct adapters. b. Attach the air duct adapter to the air duct hose using the 3in hose clamp. Do this to both adapters and both hoses c. Install air duct adapters and hoses to the air duct adapter plate. on O ct ob er 3 1, 3. ATTACH HEATER TO VEHICLE a. Lift the vehicle b. Place the E-TES heater below the rear of the vehicle. c. Connect the air mover power cord and the two E-TES heater power cords (if not already connected) d. Insert the right-side hose into the right-side frame rail until it is secure. K0 D Ex pi re d 4. 10 e. Using a bungee cord or straps around the frame rail, secure the left-side hose to the left side frame rail. The outlet of the hose must be center with the frame rail opening. 5. CALIBRATE E-TES HEATER a. Plug in the air mover power cord and the two E-TES heater power cords. 20 23 DO NOT wrap the bungee cord around any fuel, evap, or brake hoses. Only put the bungee cord around the frame rail and air duct hose to avoid damage to vehicle components. er 3 1, The air mover and E-TES heater must be plugged into separate circuits. Check your dealership electrical system to ensure the circuit you are plugging into can operate the air mover and E-TES heater. ob b. Press SELECT to set the Air Flow switch trigger point. Follow the screen directions using the DOWN button to set the levels with the air mover OFF & ON. O ct c. Turn the air mover OFF. When the air mover is off and the number stops changing, press DOWN(most cases this will be 0.) This is the Off Set Point. (Shown as 033 in this example) on d. Then turn the air mover ON at high speed. Press DOWN as soon as the number on the display steadies out (50-300). This is the ON Set Point. (Shown as 076 in this example) DO NOT CONTACT TAS for E-TES Heater concerns. K0 D Ex pi re d If you need assistance with the E-TES heater contact the Bosch Technical Assistance Line - 1-800-933-8335 (Option 4) 11 DRYING PROCEDURE (Normal procedure after initial setup) 20 23 ATTACH HEATER TO VEHICLE a. Lift the vehicle b. Place the E-TES heater below the rear of the vehicle. c. Connect the air mover power cord and the two E-TES heater power cords (if not already connected) d. Insert the right-side hose into the right-side frame rail until it is secure. e. Using a bungee cord or straps around the frame rail, secure the left-side hose to the left side frame rail. The outlet of the hose must be center with the frame rail opening. O ct ob er 3 1, 1. on DO NOT wrap the bungee cord around any fuel, evap, or brake hoses. Only put the bungee cord around the frame rail and air duct hose to avoid damage to vehicle components. TURN THE AIR MOVER ON THE HIGH SETTING K0 D Ex pi re d 2. 4. 3. TURN THE E-TES HEATER ON AND DRY FRAME a. Flip the switch on the E-TES Heater to the “on” position b. Check that the air coming out of the heater is warm. c. Leave the heater and air mover ON and attached to the vehicle for 3 hours. The drying procedure being performed as written is critical for the wax application procedure success. If the drying procedure is not performed correctly the maximum rust prevention will not be achieved. REMOVE E-TES HEATER AND HOSES FROM VEHICLE 12 5. DRY THE OPEN SECTION OF THE FRAME AND INNER CAB MOUNTS a. Using the 2ft air gun, remove all water from the open section of the frame and the inside of the cab mounts on both the right and left side of the frame. All the water between the metal reinforcements in the open section of the frame MUST BE REMOVED before proceeding IT IS CRITICAL THAT YOUR SHOP AIR SYSTEM NOT HAVE WATER IN IT. K0 D Ex pi re d on O ct ob er 3 1, 20 23 Confirm by spraying the air gun at a piece of carboard (or other water absorbant material) to confirm that no water is present. If water is present then the shop air dryer may need to be drained or replaced. 13 11-15 MODEL YEAR CLEANING PROCEDURE Before starting this process, review the SCK0D E-Learning Cleaning section for key details USE EXTENDED WIRE BRUSH TO CLEAN THE RH FRAME RAIL BOXED SECTION a. Inspect the brush to confirm the bristles are not lose or worm 20 23 1. Insert the brush into the frame rail as shown in the illustration er 3 b. 1, If the wire brush has worn down to the point of not being effective or you have an issue with any other tool related to K0D contact Bosch Technical Assistance Line - 1-800-933-8335 (Option 4) for instructions on how to acquire replacement parts DO NOT insert the brush beyond the point shown in the illustration below, otherwise brush damage will occur With the drill direction set to clockwise, run the drill in and out of the box section frame to break free rocks, dirt, and rust. DO NOT SET THE DRILL DIRECTION TO COUNTERCLOCKWISE Ex c. pi re d on O ct ob NOTE: When handling the Power Tool Wand, make sure to hold onto the plastic handle for safety K0 D NOTE: The amount of time needed to run the brush will vary from frame to frame. The typical time will be 5 to 10 minutes per side however it may take longer depending on how dirty the frame is and the type of dirt/debris in the frame 14 2. USE WIRE BRUSH WITH DRILL TO CLEAN THE LH FRAME RAIL BOXED SECTION a. Insert the wire brush (power tool) below the brake lines. b. 20 23 Be careful not to damage the brake lines when inserting the wire brush Clamp the plastic handle to the frame rail using a C-Clamp to avoid damage to the brake lines With the drill direction set to clockwise, run the drill in and out of the box section frame to break free rocks, dirt, and rust. ob c. er 3 1, NOTE: Depending on the vehicle, you may need to add something below the plastic handle (such as a piece of wood) if the C-Clamp is not able to secure the plastic handle. O ct NOTE: The amount of time needed to run the brush will vary from frame to frame. The typical time will be 5 to 10 minutes per side however it may take longer depending on how dirty the frame is and the type of dirt/debris in the frame d. Install the cab mount frame plug Plug Part Number: 90950-A1008 K0 D Ex pi re d on Be careful not to damage the brake lines when removing the wire brush 15 CONFIRM CAB MOUNTS CLEANLINESS a. Using the endoscope provided to your dealer in the J0M campaign, confirm the inside of the cab mount is clean focusing on the inner corners 1, 4. CLEAN BOTH FRONT CAB MOUNTS a. If there is hardened dirt or other difficult to remove debris, use the rubber mallet to hit the outside of the cab mount to break up the debris b. Using the 2ft Air Gun, blow out all the dirt and debris inside the cab mount focusing on the inner corners. 20 23 3. If the cab mount is not clean enough, repeat steps 1-2 until clean Inner Corner of the Cab Mount CLEAN THE OPEN SECTION OF THE FRAME (both LH and RH) a. Clean the welds and area highlighted in the illustrations below using the wire brush (Hand Tool) show in the illustrations below until no dirt, debris, or rust is present on the welds d 5. on O ct ob b. er 3 NOTE: The images below show the “minimum cleanliness” that the cab mounts can be. The frame can be cleaner than the images below but cannot be less clean. re NOTE: The cross member may not be present on short wheel base frames K0 D Ex pi FRONT 16 6. REMOVE DIRT AND DEBRIS FROM FRAME a. Using the 2ft Air Gun, blow out all the dirt and debris working from the front of the vehicle to the back using the various plug holes. You may have to remove plugs from the frame to blow out all debris. Only remove the plugs in the sections being cleaned. ob er 3 1, 20 23 NOTE: It will normally take 4 to 5 passes with the air gun to remove the all the debris from the frame REMOVE DUST AND DEBRIS FROM OPEN SECTION (LH AND RH SIDE) a. Blow any dust, or debris that might be on the opens section shown below. Ex 7. pi re d on O ct NOTE: Confirm no rocks or other debris are stuck in the channel shown below on the LH and RH side of the frame FRONT K0 D NOTE: The cross member may not be present on short wheel base frames 17 8. CONFIRM FRAME CLEANLINESS a. Using the endoscope provided to your dealer in the J0M campaign, confirm the inside of the frame is clean by inserting the endoscope into various plug holes b. If the frame is not clean enough repeat the cleaning procedure until clean enough 20 23 NOTE: The images below show the “minimum cleanliness” that the frame can be. The frame can be cleaner than the images below but cannot be less clean. ob er 3 1, The frame must be cleaned before applying the wax. If the frame is not completely clean then the wax coating will not adhear to the frame properly K0 D Ex pi re d on O ct If the wire brush has worn down to the point of not being effective or you have an issue with any other tool related to K0D contact Bosch Technical Assistance Line - 1-800-933-8335 (Option 4) for instructions on how to acquire replacement parts 18 WAX APPLICATION WORK PROCEDURE K0 D Ex pi re d on O ct ob er 3 1, 20 23 A. CIRCUIT OF THE APPLICATION UNIT 19 B. COMPONENTS OF THE APPLICATION UNIT SYSTEM Control Panel 1. Air inlet port 2. Air closing lever 3. Air pressure Gauge 4. Air regulator 1 3 Heater Adjust Dial 4 2 120V power supply cable Sealer Gun (Low Pressure) 1, Ground cable er 3 Short/Long Wand Spray Gun (High Pressure) Wax pail Inlet drain lever on SETTINGS Inlet drain hose Back Pressure 9 MPa (1305 psi) re d Pump Output Pressure Gauge 14 MPa (2031 psi) Filter drain hose / lever O ct ob Suction pipe 2. Temperature Gauge 20 23 1. pi Adjust air regulator K0 D Ex High Pressure 12 MPa (1741 psi) Adjust red dial Adjust black dial Sealer Pressure 0.5 - 4 MPa (73 - 580 psi) Adjust red dial 20 C. WAND SPECIFICATION WAND SHORT WAND 20 23 1. er 3 The tip of the short wand has 5 orifices to spray out wax. The tip of the long wand has 6 orifices to spray out wax. O ct ob 2. SEALER GUN 1. Simple tubular tip. 2. The amount of wax applied is judged visually. WAND TIP 1, LONG WAND WAND TOP MARK The punch marks found on the wand tip side and gun side are the TOP marks. Confirm that the TOP mark is facing upward at all time. on 3. Gun Side (Wand & Joint) K0 D Ex pi re d Tip Side (Tip & Wand) 21 4. INSTALLATION OF THE WAND TO THE GUN (SHORT & LONG WAND) Connect the short or long wand to the gun by sliding in (Quick connector). Adjust the wand connecting portion to set the TOP mark upward. Direction for LH side K0 D Ex pi re d on O ct ob er 3 Direction for RH side 1, 20 23 DO NOT use red shop towels or other lint products when handling the wands as they will cause a clogged tip. Only use lint free towels when handling the wands 22 D. INITIAL SET UP PREPARE THE WAX PAIL Press the center of the cap and remove. Remove the plastic inner cap. Open the lever and remove the lid. 20 23 1. ADD THROAT SEALING LIQUID a) A bottle of Throat Sealing Liquid (TSL) can be found on attached near the wheel of the pump assembly. This bottle will be used as part of maintenance of the pump. Store the bottle in an accessible area. b) Before pump operation fill the white colored TSL dish halfway with TSL fluid. 3. pi re d on O ct 2. ob er 3 1, Remove the strainer from the suction pipe and insert the pipe into the cap hole of the lid. Reinstall the strainer to the pipe and then reinstall the wax lid to the can. Be careful to NOT let the pipe, strainer and lid contact foreign materials when working and DO NOT allow any foreign materials enter the wax pail. CHECK THROAT SEALING LIQUID LEVEL a) Remove the TSL cover screw and remove the cover b) Confirm the TSL dish is filled half way with TSL fluid You will need to check the TSL level every day, or if the pump has been moved before pump operation. Ex D K0 Contact Bosch Technical Assistance line to order additional TSL fluid. Bosch Technical Assistance Line 1-800-933-8335 (Option 4) 4. SYSTEM SET UP Lock the triggers of the high pressure spray gun and sealer gun. Connect the short wand to the high pressure gun 23 Connect the ground cable. 20 23 DO NOT connect to vehicle ground. er 3 1, Connect the shop air hose to the air inlet port. Open the air closing lever. Open the filter drain lever (yellow). Turn the air regulator to adjust the air pressure to less than 0.07 MPa (10 psi) on the air pressure gauge. Place a container under the filter drain hose and wait until white wax continuously comes out. Close the filter drain lever (yellow) once all the air is removed. Confirm the heater adjust dial is set to off Connect the 120V power supply cable. DO NOT turn the heater on until the entire system is primed with wax and free of air otherwise damage may occur Adjust the heater adjust dial to 6 to warm up the wax. Confirm the green light turns on when heater adjust dial first adjusted. Note: It can take 30 minutes or more to bring the wax up to temperature depending on room temperature. Continue with the process while the wax heats up. K0 D Ex pi re d on O ct ob Turn the inlet drain lever (black) to drain side (arrow to inlet drain hose side) and place a container under the filter drain hose and wait until white wax continuously comes out. Close the inlet drain lever (black) once all air is removed by turning the arrow back towards the inlet feed line. 24 Turn the air regulator to adjust the pump output pressure to 14 MPa (2031 psi). NEVER set the pressure to be over 14 MPa (2031 psi). 20 23 Turn the high pressure regulator (red dial) to adjust the high pressure to 12 MPa (1741 psi). NEVER set the pressure to be over 12 MPa (1741 psi). ob er 3 1, Confirm the inlet drain lever (black) is pointing towards the inlet feed hose. K0 D Ex pi re d on O ct Turn the back pressure regulator (black dial) to adjust the back pressure to 9 MPa (1305 psi). Turn the sealer pressure regulator (red dial) to adjust the sealer pressure to 0.5 - 4 MPa (73 - 580 psi). NOTE: Adjust the pressure within the range to make it easy to work with when applying wax. Do Not set the pressure to be over 4 Mpa (580 psi) Operate the sealer gun to drain wax. Reference Value: 100 ml Operate the high pressure spray gun to drain wax. Reference Value: 100 ml 25 5. SET UP CONFIRMATION 20 23 Confirm that the wax temperature is 40 ºC (104 ºF) on temperature gauge. NOTE: If the wax temperature is not heated enough, please wait for a couple of minutes. It may be necessary to turn the dial to a higher level depending on air temperature in the shop. DO NOT warm up the wax temperature higher than 50 ºC (122 ºF). If the wax has been overheated the system will need to be flushed with new wax prior to application er 3 1, If the system needs to be drained due to overheating the wax you must drain 2L of wax from the inlet drain lever (black) ob Confirm pump cycle rate. Standard Value: 7 – 10 times/min NOTE: If the pump cycle rate is faster or slower than the standard value, turn the back pressure regulator to adjust the rate within the range. O ct Confirm that the pump output pressure is 14 MPa (2031 psi). If not, adjust the air regulator to meet 14 MPa (2031 psi). Ex pi re d on NEVER set the pressure to be over 14 MPa (2031 psi). Confirm that the high pressure is 12 MPa (1741 psi). If not, adjust the high pressure regulator (red dial) to meet 12 MPa (1741 psi). NEVER set the pressure to be over 12 MPa (1741 psi). Confirm that the sealer pressure is 0.5 - 4 MPa (73 - 580 psi). NEVER set the pressure to be over 4 MPa (580 psi). K0 D Check each line for wax leakage. If there is any wax leakage, stop using the system immediately and contact the following number for assistance: Bosch Technical Assistance Line - 1-800-933-8335 (Option 4) 26 E. SETTINGS AFTER WORK SETTINGS AFTER WORK Close the air closing lever. Turn the heater adjust dial off. Disconnect the shop air hose. Disconnect the 120V power supply cable and ground cable. 20 23 1. K0 D Ex pi re d on O ct ob er 3 1, Cover the guns and wands with plastic wrap to protect them from dust. Close the lid of the wax pail securely and wrap the cover of the pail with plastic wrap. Store the wax pail indoors avoiding any heat source. NOTE: The wax can be used for 2 months once opened. After that it must be replaced with new wax. 27 K0 D Ex pi re d on O ct ob er 3 1, 20 23 F. REMOVAL PARTS Reference the appropriate repair manual on TIS for parts removal procedures. 28 G. MASKING AROUND WORK STALL NOTE: Depending on the shop layout, it may be necessary to put barriers to prevent accidental over spray Masking on the floor is unnecessary. (if wax falls from the frame, clean the spill right away to avoid a fall hazard) VEHICLE MASKING NOTE: In this work, masking needs to be done only partially as the drips and scattering are few. 20 23 1. er 3 1, Using an infrared thermometer ensure the exhaust has cooled. Cover the holes from which wax can spill out using shop cloths or the likes. K0 D Ex pi re d on O ct ob Protect each brake tube as the wand may hit them. (LH Side Only) 29 2. PLUG HOLES IN THE FRAME Apply all the plugs other than the ones indicated with stars (★) on Hole Plugs Installation Check Sheet found in appendix. 20 23 DO NOT install the plugs indicated with stars (★) until the wax application is completed. Those plug holes will be used when inserting a wand to apply wax. K0 D Ex pi re d on O ct ob er 3 1, NOTE: You may have to remove certain stickers to install optional equipment. Some vehicles may not have plug holes or may have plugs already installed depending on the vehicle specification or model year. Make sure all the plugs are flush with the frame. Make sure the surface of the frame is clean before you apply stickers. Apply masking tape to the holes shown in the illustration from which wax can spill out. NOTE: The masking tape has to be applied on both LH and RH side of the frame even when the illustrations show only one side. 30 H. APPLY WAX WITH SHORT WAND Before starting this process, review the SCK0D E-Learning Spray Application section for key details 1. PREPARE FOR WAX APPLICATION 20 23 CHECK THE REMAINING WAX AMOUNT 1. Check that more than 1/3 of wax is in the wax pail. If not, add NEW wax to fill up the can. The wax level must NOT be less than 1/4 as the pump starts suctioning air. 1, NOTE : 1 wax pail (18 Liters) is for 3 to 4 vehicles. ob er 3 CHECK PUMP CYCLE RATE Standard Value: 7 - 10 times/mins NOTE: If the pump cycle rate is faster or slower than the standard value, turn the back pressure regulator to adjust the rate within the range. NEVER set the pressures to be over the specified values. CHECK WAX TEMPERATURE Standard Value: 40 ºC (104 ºF) DO NOT warm up the wax temperature higher than 50 ºC (122 ºF) K0 D Ex pi re d on O ct CHECK EACH PRESSURE Standard Value: Pump output pressure: 14MPa (2031 psi) High pressure: 12 MPa (1741 psi) Sealer pressure: 0.5 - 4 MPa (73 - 580 psi) 31 1, 20 23 CHECK SPRAY PATTERN 1. Connect the short wand to the high pressure spray gun. 2. Weigh the empty cup and zero the scale 3. Spray 1 shot of wax on Paint Prep cup (Φ 10 - 15 cm (3.94 - 5.91 in.) for paint work). 4. Visually inspect the wax discharged from 5 orifices is continuously connected. (Refer to XII. C. WAND SPECIFICATION) ob er 3 CHECK WAX DISCHARGE AMOUNT 1. Measure the weight of the empty Paint Prep cup. 2. Spray 10 shots of wax into Paint Prep cup and measure the entire weight. NOTE: Fully pull the spray gun trigger to stabilize the discharge amount of wax per shot. You may need to practice to be able to spray 10 g (0.353 oz.) of wax per shot. DO NOT spray 10 shots continuously as the pressure lowers. on O ct 3. Subtract the weight of Paint Prep cup and calculate the weight of 1 shot. Standard Value: 100 – 120 g (3.53 - 4.23 oz.) [10 - 12 g (0.353 - 0.423 oz.) per shot] CHECK WAND TOP MARKS 1. Confirm that the TOP marks on the wand are on the upper side when using the high pressure spray gun with short or long wand. (Refer to XII. C. WAND SPECIFICATION) K0 D Ex pi re d • When replacing the high pressure wands (short or long), make sure to perform the checks shown above every time. • If the gun trigger is pulled when the pump is operating, wax cannot be applied properly. In such a case, redo the procedure to check properly. • DO NOT DISCARD INITIAL SPRAY CHECK CUP. You will need to upload an image of the spray cup at a later step 32 INSERT FROM THE INNER APPLICATION HOLE TOWARDS FRONT * The illustrations show RH side only. Use the same procedure for LH side. ALL MODEL YEARS er 3 1, 20 23 2. ob If the gun trigger is pulled when the pump is operating, wax cannot be applied properly. In such a case, spray wax again at the same place. Pull back the wand 1 notch and spray 1 shot. Repeat step c) until the gun hits the frame crossmember sub-assembly No.3. K0 D Ex pi re d on O ct Insert the short wand forward up to mark 1 so that the wand touches the middle of the side of the application hole. Spray 1 shot to apply wax. Change the wand angle upward at the position where the gun hit the frame crossmember sub-assembly No.3. NOTE: Place the wand so that it touches the opposing corners of the application hole. Be cautious as the spraying interval will change because the notch will be at every 5 mm (0.197 in.) at the last part of the wand. 33 3. 20 23 Spray 1 shot and repeat step c) until Mark 5 appears. When spraying the last few shots, cover the application hole with your hand so that wax does not splash out. Apply masking tape on the application hole. REINSTALL THE FRONT SUSPENSION MEMBER BRACKET (IF EQUIPPED) Reinstall the front suspension member bracket. Torque: 33 N*m (337 kgf*cm, 24 ft.*lbf) INSTALL THE NEW BOLTS (W/O FRONT SUSPENSION MEMBER BRACKET ONLY) Install the 2 NEW bolts. Torque: 33 N*m (337 kgf*cm, 24 ft.*lbf) ob 4. er 3 1, Be sure to install at this step. Plug Hole Kit CRC Application 3 (2011-2015MY) Part Name Bolt w/Washer Qty 4 K0 D Ex pi re d on O ct Part # 90119-A0169 34 INSERT FROM THE INNER OPENING TOWARDS FRONT * The illustrations show RH side only. Perform the same procedure for LH side. er 3 1, 20 23 5. ob If the gun trigger is pulled when the pump is operating, wax cannot be applied properly. In such a case, spray wax again at the same place. on O ct Insert the short wand forward up to Mark 3 and spray 1 shot. NOTE: The wand should be placed as close to the center as possible. Ex pi re d Pull back the wand 10 mm (0.394 in.) and spray 1 shot. K0 D Repeat step b) until Mark 5 appears. NOTE: DO NOT spray wax at each 5 mm (0.197 in.) notch. Spray every 10 mm (0.394 in.) though the notches are at both 10 mm (0.394 in.) and 5 mm (0.197 in.) intervals. 35 FROM THE BOTTOM SQUARE HOLE TO THE TOP * The illustrations show RH side only. Perform the same procedure for LH side. er 3 1, 20 23 6. ob If the gun trigger is pulled when the pump is operating, wax cannot be applied properly. In such a case, spray wax again at the same place. on O ct Remove the masking tape applied to the application hole. Set the guide on the wand according to the mark. (The guide is supplied for LH and RH respectively.) Ex pi re d Insert the wand until it hits the frame inner top. Apply masking tape to the application hole. REPEAT THE PROCEDURE ON THE OTHER SIDE Repeat from the step 2 to 7 on the other side of the frame side rail. K0 D 7. Spray 4 shots to apply wax. NOTE: Spray 4 shots at one spot. 36 APPLY WAX WITH LONG WAND * The illustrations show RH side only. Perform the same procedure for LH side. • Wax temperature Confirmation • Spray pattern Before wax application • Wax Discharge Amount (Refer to XII. H. 1. PREPARE FOR WAX APPLICATION) • TOP mark positions ob er 3 1, 20 23 I. FROM THE OUTER SQUARE HOLE TO THE FRONT Peel the masking tape half way back on the application hole. Insert the wand forward up to Mark 1 and spray 1 shot. K0 D Ex pi re d on 1. O ct If the gun trigger is pulled when the pump is operating, wax cannot be applied properly. In such a case, spray wax again at the same place. 37 20 23 Pull back the wand 1 notch and spray 1 shot. NOTE: Be cautious as the spraying interval will change because the notches are at both 5 mm (0.197 in.) and 10 mm (0.394 in.) intervals. O ct REPEAT THE PROCEDURE ON THE OTHER SIDE Repeat the step 1 on the other side of the frame side rail. K0 D Ex pi re d on 2. ob er 3 1, Repeat step c) until Mark 2 appears. When spraying the last few shots, cover the application hole with your hand so that wax does not splash out. Apply masking tape on the application hole. 38 AROUND THE REINFORCEMENT AND CROSSMEMBER Apply wax to the gap and edge between the reinforcement and side rail. NOTE : The amount of wax can be visually controlled. The distance between the crossmember and the reinforcement may vary depending on the vehicle K0 D Ex pi re d on 1. O ct ob er 3 1, 20 23 J. APPLY WAX WITH SEALER GUN * The illustrations show RH side only. Perform the same procedure for LH side. Confirmation Before wax application • Wax temperature (Refer to XII. H. 1. PREPARE FOR WAX APPLICATION) 39 d on O ct ob er 3 1, 20 23 Fill wax into the gap between the side rail and reinforcement. NOTE : Cover the top of the gun with your hand as shown in the illustration and fill wax enough until it comes out from between the fingers. Fill wax from the upper side of the gap. NOTE : Make sure to fill the wax as much as they come out. K0 D Ex pi re Apply wax to the gap and edge between reinforcement and side rail. 40 on O ct ob er 3 1, 20 23 Apply wax to the gap and edge between reinforcement and side rail. Apply wax to the gap and edge between crossmember and side rail. NOTE: Insert the sealer gun tip from the front and rear hole of the crossmember to apply wax inside the crossmember properly. These steps e) and f) are not needed for short wheel base vehicle configuration. K0 D Ex pi re d Apply wax to the gap and edge between reinforcement and side rail. 41 d on O ct ob er 3 1, 20 23 Apply wax to the gap and edge between reinforcement and side rail. Apply wax to the gap and edge between front inner channel and side rail. K0 D Ex pi re Apply wax to the gap and edge between front inner channel and side rail. 42 INSIDE CAB MOUNT Insert the sealer gun tip from the holes which are on the bottom surface of the cab mount and apply wax to the gap between the cab mount and side rail. 3. REPEAT THE PROCEDURE ON THE OTHER SIDE Repeat the steps 1 and 2 on the other side of the frame side rail. K0 D Ex pi re d on O ct ob er 3 1, 20 23 2. 43 4. INSTALL THE BODY PLUGS Remove the masking tape and scrape out the wax applied around the inside of the plug hole, and then install the NEW plug (90950-01A24). K0 D Ex pi re d on O ct ob er 3 1, Remove the masking tape and install the NEW plugs (90950-01991, 90950-01987). 20 23 The plug must be installed with the openings facing the side of the vehicle and the tabs facing the front a rear to ensure road spray does not enter the frame through the plug. 44 CHECKSHEET AND RECORD KEEPING 1. COMPLETE POST-SPRAY CHECKSHEET (THIS MUST BE DONE FOR EVERY VEHICLE) a. Click the link below to access the frame check sheet (USE IE FOR ALL SUBMISSIONS) https://one.tis.toyota.com/t3Portal/frameSprayCheck?l=tis_frame_spray&campaignCode=K0D&vin=&c ampaignId=5&source=tech 20 23 NOTE: VEHICLES FOUND WITH AFTERMARKET WAX Vehicles that come into dealership that already have wax applied from the plant can be determined by using the parts look up site mentioned on page 3. Any vehicle that has had wax application from the plant do NOT require a Checksheet. er 3 1, Vehicles found with an aftermarket wax sprayed over K0D coverage areas will need a Checksheet completed. Below are examples of aftermarket wax coverage. If aftermarket wax covers an area covered by K0D, CRC used in K0D should NOT be applied over the top. Only apply K0D CRC in areas that are not covered by aftermarket CRC but are covered under K0D normally. Also install plugs and covers as customary in K0D. K0 D Ex pi re d on O ct ob Examples of aftermarket CRC 45 b. Answer the questions and enter your initials throughout the check sheet 20 23 c. Upload photos to the check sheet Note: -All the photos must be taken and have the required parts as shown in the steps below -All photos must be less than 3MB each -All photos must be uploaded before the check sheet is completed. er 3 1, d. Spray Cup Image - Photo must be taken from the top view and show a completed wax ring in the cup - R.O. Number must be in the picture O ct ob e. Left/Right Inner Box Section Image - Photo must be taken at the opening of the box section and show the top, bottom, and side walls of the box section - R.O. number must be in the picture NOTE: It is recommended you either use a camera flash or back light to clearly show the interior of the box section Left/Right Open Section Image - Photo must be taken from a distance where the entire wax application along the open section can be seen. - The R.O. must be in the picture g. Left/Right Wheel Well Image - Photo must be taken from an angle that has all the plugs installed on the outer rail of the frame - The R.O. must be in the picture Ex pi re d on f. Sign the check sheet Have your Service Manager or Shop Forman sign the check sheet. Submit the check sheet. Using the print function, attached the completed check sheet to the R.O. A check sheet must be completed for each vehicle sprayed K0 D h. i. j. k. 46 INSTALLATION OF FRAME SEAL * The illustrations show LH side only. Perform the same procedure for RH side. 1. INSTALL FRAME RAIL SEAL 1, 20 23 Using Template C and D, modify both the left and right side frame seal by drilling a (3/8”) hole in the location shown. ob er 3 Install the bolt through the frame and torque the flange nut. Torque: 18.5 N*m (189 kgf*cm, 14 ft.*lbf) Install the washer onto the bolt. Install the frame seal second washer and locking nut onto the frame and torque to spec. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) Plug Hole Kit CRC Application 1 (2011-2015MY) O ct Part # 94183-00831 94611-10800 Part Name Nut, Lock Washer, Plate Part # 90178-A0112 90105-A0356 5114A-04010 5114B-04010 Part Name Nut, Flange Bolt, Flange Seal, Frame Side Rail, RH Seal, Frame Side Rail, LH Qty 2 2 1 1 d on Plug Hole Kit CRC Application 3 (2011-2015MY) Qty 2 4 RESTORE THE VEHICLE Remove all the remaining masking materials. Wipe off all the unnecessary wax remaining on the vehicle. Reinstall all the removed parts. Reinstall wheels and torque to spec. Steel Wheel / Aluminum Wheel Torque: 113 N*m (1152 kgf*cm, 83 ft.*lbf) Lower the vehicle. D Ex pi 1. re RESTORATION WORKS K0 RECORD-KEEPING AND OTHER REQUIREMENTS To make sure that your dealership can satisfy specific state and local requirements, please refer to your specific state Dealer Information Packet. A. B. C. D. APPENDIX WAND TIP CLEANING PRIMARY FILTER CLEANING PLUG CHECKSHEET AND FISHTALE COVER TEMPLATES NOX-RUST 712THV-T SDS 47 A. WAND TIP CLEANING * The illustrations show the short wand tip; However, the process can be used for the long wand tip as well. REMOVE TIP Remove tip from the wand by using wrench. 20 23 1. Wipe off the wax on outer surface of the tip 1, REMOVE WAX a) Blow air into each orifice to remove wax and any foreign material er 3 2. O ct ob b) Repeat air-blow until as much material can be removed as possible 3. RE-ASSEMBLE WAND a) Tape the wand thread by sealant tape. Ex pi re d on Reference: Tape the threads twice b) Assemble the tip and wand by wrench until the end of tip is 24mm from 1st notch. (See picture) c) Adjust the tip angle to meet the top mark on the tip and top mark on the wand. (the long wand tip may not have marks to align. In that case adjust the end of the tip to be 24mm from the first notch) Note : Only adjust the tip angle when tightening The distance between the end of the tip and the first notch is critical for a proper spray pattern: Short Wand - 24mm, Long Wand – 6mm D K0 The sealant tape should not be applied near the end of the threads to avoid sealant tape entering the wand. End of tip 1st notch 24mm d) Check spray pattern to confirm tip is no longer clogged. If clogged repeat step one through 3. Note: If the tip cannot be unclogged after multiple attempts call the Bosch Technical Assistance Line - 1-800-933-8335 (Option 4) to order a new wand. 48 B. Primary Filter Cleaning 1. Depressurize System 2. 1, 20 23 Remove shop air source from inlet port Drain Filter Housing Using Valve 3. Filter Housing Removal Remove filter housing by rotating filter housing counter clockwise. *Note filter housing should be removed by hand. K0 D Ex pi re d on O ct ob er 3 Drain the filter by using the drain valve located directly below Pump output pressure gauge. *Note valve should remain open until completing step 9 49 4. Removing Filter From Filter Housing 20 23 Remove filter from filter housing *Note filter should be removed by hand to prevent damage to mesh. Separate Filter Body and Filter Mesh 1, 5. 6. ob er 3 Push down on locating pintle to assist in removing filter body from mesh filter. Remove filter body from filter mesh completely. Clean Filter Mesh and Filter body 7. Use compressed air to blow any remaining foreign material or CRC from filter mesh or filter body. Install Filter Body Into Filter Mesh Install cleaned filter body into mesh filter, ensure pintle is seated in locating hole. K0 D Ex pi re d on O ct Remove any foreign material or residual CRC from filter mesh and filter body using mineral spirits or equivalent cleaning solvent. *Note lint free material should be used when wiping the filter mesh clean. 8. Install Filter Into Filter Housing Install cleaned filter into filter housing *Note pintle side of filter should be inserted into filter housing first. 50 9. Filter Housing Installation er 3 1, 20 23 Filter housing should be installed by rotating filter housing clockwise. *Note filter housing should be hand tight similar to canister style oil filter. ob 10. Bleeding procedure Turn the inlet drain lever (black) to drain side (arrow to inlet drain hose side) and place a container under the filter drain hose and wait until white wax continuously comes out. Close the inlet drain lever (black) once all air is removed by turning the arrow back towards the inlet feed line. K0 D Ex pi re d on O ct Connect the shop air hose to the air inlet port. Open the air closing lever. Open the filter drain lever (yellow). Turn the air regulator to adjust the air pressure to less than 0.07 MPa (10 psi) on the air pressure gauge. Place a container under the filter drain hose and wait until white wax continuously comes out. Close the filter drain lever (yellow) once all the air is removed. 51 35 52 D K0 Ex re pi d on 1, er 3 ob O ct 20 23 36 D K0 Ex re pi d on 1, er 3 ob O ct 20 23 D K0 38 re pi Ex d on ct ob er 31 , O 20 23 D K0 39 re pi Ex d on ct ob er 31 , O 20 23 D K0 40 re pi Ex d on ct ob er 31 , O 20 23 D K0 41 re pi Ex d on ct ob er 31 , O 20 23 D K0 1 Ex d re pi on er ob ct O 3 02 ,2 31 D K0 2 Ex d re pi on er ob ct O 3 02 ,2 31 D K0 3 Ex d re pi on er ob ct O 3 02 ,2 31 D K0 4 Ex d re pi on er ob ct O 3 02 ,2 31 D K0 5 Ex d re pi on er ob ct O 3 02 ,2 31 D K0 6 Ex d re pi on er ob ct O 3 02 ,2 31 D K0 7 Ex d re pi on er ob ct O 3 02 ,2 31