NTB24-003A

Classification:
Reference:
EL24-001A
Date:
NTB24-003A
March 11, 2024
VOLUNTARY SERVICE CAMPAIGN
2021-2023 ROGUE; IPDM CONFIGURATION
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.
CAMPAIGN ID #:
APPLIED VEHICLES:
P3A28, PD108
2021-2023 Rogue (T33)
Check Service COMM or Dealer Business Systems (DBS)
National Service History to confirm campaign eligibility.
INTRODUCTION
Nissan is conducting this voluntary service campaign on certain specific model year 2021-2023
Rogue vehicles to reconfigure the IPDM settings for electric energy management. This service
will be performed at no charge to the customer for parts or labor.
IDENTIFICATION NUMBER
Nissan has assigned identification numbers P3A28 and PD108 to this campaign. The
applicable identification number must appear on all communication and documentation of any
nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service
department. This includes vehicles purchased from private parties, vehicles presented by
transient (tourists) owners, and vehicles in a dealer’s inventory.
Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly
trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and
safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it
does. See your Nissan dealer to determine if this applies to your vehicle.
1/9
SERVICE PROCEDURE
IMPORTANT: Before starting, make sure:

ASIST on the CONSULT PC has been synchronized (updated) to the current date.

All CONSULT-III plus software updates (if any) have been installed.
o
Updated configuration may not install correctly if the latest C-III plus software is
not installed.
IPDM Configuration
1.
Connect a battery maintainer or smart charger, set to reflash mode or a similar setting, to
the vehicle battery.
2.
Confirm that the CONSULT PC is connected to Wi-Fi.
3.
Connect the Vehicle Interface (VI) to the vehicle.
4.
Turn the ignition ON with the engine OFF.
5.
Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC, blower,
rear defogger, audio, NAVI, seat heater, steering wheel heater, etc.
6.
Turn the hazard warning lamps ON and leave them ON for the duration of the procedure.
7.
Start CONSULT-III plus on the CONSULT PC.
8.
If prompted, select USA/CANADA Dealers from the drop-down menu, and then select
OK.
9.
Login using your NNAnet credentials.
IMPORTANT: If not prompted to enter your username and password, the CONSULT PC
may not be connected to Wi-Fi. Close C-III plus, confirm the CONSULT PC is connected
to Wi-Fi, and then reopen C-III plus.
2/9
NTB24-003A
10.
Wait for the VI to be recognized.

11.
The serial number will be displayed when the VI is recognized.
Select Re/programming, Configuration.
VI is
recognized
Figure 1
3/9
NTB24-003A
12.
Use the arrows (if needed) to view and read all precautions.
13.
Check the box confirming the precautions have been read.
14.
Select Next.
Figure 2
15.
Select Automatic Selection(VIN), and then select Detect Vehicle.
Example
Figure 3
4/9
NTB24-003A
16.
Make sure VIN or Chassis #, Vehicle Name, and Model Year are correct for the vehicle
you are working on, and then select Confirm.
XXXXXXXXXXXXXXXXX
Rogue T33
XXXX
Figure 4
17.
Verify the VIN is correct for the vehicle you are working on, and then select Confirm.
XXXXXXXXXXXXXXXXX
Figure 5
5/9
NTB24-003A
18.
Locate and select IPDM E/R.
Figure 6
19.
Select Configuration.
Figure 7
6/9
NTB24-003A
20.
Select START.
XXXXXXXXXXXXXXXXX
Figure 8
21.
Allow the configuration to download to the IPDM.

The configuration will take approximately 3 minutes to complete.
XXXXXXXXXXXXXXXXX
Figure 9
7/9
NTB24-003A
22.
When the screen in Figure 10 displays, the configuration is complete.

After the configuration is complete, the configuration part number will display in the
DATA PART NO. field.

Select Print Screen at the top of the screen and attach the results to the repair
order.

If DATA PART NO. displays “00000000000” after configuration, make sure
C-III plus has been updated to the latest level and reconfigure the IPDM/ER.
XXXXXXXXXXXXXXXXX
XXXXXXXXX
Figure 10
23.
Select End to return to the home screen.
XXXXXXXXXXXXXXXXX
XXXXXXXXX
Figure 11
8/9
NTB24-003A
24.
Close C-III plus and disconnect the VI.
25.
Turn the vehicle OFF.
26.
Turn the hazard warning lamps OFF.
27.
Turn OFF the battery maintainer or smart charger and disconnect it from the vehicle.
28.
Close the hood.
CLAIMS INFORMATION
Submit a “CM” line claim using the following claims coding:
CAMPAIGN (“CM”) ID
DESCRIPTION
P3A28 (1)
Reconfigure IPDM
(1) The 11th character of the VIN is “W”.
OP CODE
FRT
P3A280
0.4
OP CODE
FRT
PD1080
0.4
OR
Submit a “CM” line claim using the following claims coding:
CAMPAIGN (“CM”) ID
DESCRIPTION
PD108 (1)
Reconfigure IPDM
(1) The 11th character of the VIN is “C”.
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
January 17, 2024
March 11, 2024
NTB24-003
NTB24-003A
DESCRIPTION
Original bulletin published
Campaign ID PD108 added to CAMPAIGN ID #,
IDENTIFICATION NUMBER, and CLAIMS
INFORMATION
9/9
NTB24-003A