LI27.60-P-077704
Service Bulletin Details
Public Details for: LI27.60-P-077704
Dsi selection lever module cannot be switched to park position "p" - malfunction of "p" button note: vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "enga
- 2024 - 2023 - 2022 - 2021 - 2020 - 2019 -
Models from 2023
2023 MERCEDES-BENZ AMG GT43 |
2023 MERCEDES-BENZ AMG GT53 |
2023 MERCEDES-BENZ AMG GT63 |
2023 MERCEDES-BENZ AMG GT63 S |
Models from 2022
2022 MERCEDES-BENZ AMG GT43 |
2022 MERCEDES-BENZ AMG GT53 |
2022 MERCEDES-BENZ AMG GT63 |
2022 MERCEDES-BENZ AMG GT63 S |
Models from 2021
2021 MERCEDES-BENZ AMG GT43 |
2021 MERCEDES-BENZ AMG GT53 |
2021 MERCEDES-BENZ AMG GT63 |
2021 MERCEDES-BENZ AMG GT63S |
Models from 2020
2020 MERCEDES-BENZ AMG GT 63 |
2020 MERCEDES-BENZ AMG GT43 |
2020 MERCEDES-BENZ AMG GT53 |
2020 MERCEDES-BENZ AMG GT63 |
2020 MERCEDES-BENZ AMG GT63S |
Models from 2019
2019 MERCEDES-BENZ AMG GT 63 |
2019 MERCEDES-BENZ AMG GT53 |
2019 MERCEDES-BENZ AMG GT63 |
2019 MERCEDES-BENZ AMG GT63S |
Direct Selection Lever Module Cannot be Switched to Park Position "P" - Malfunction of "P" Button Topic number LI27.60-P-077704 Version 1 Function group 27.60 - Gearshift, control Date 4/5/24 Validity Valid for vehicles of model series 290 with DSI (center gearshift) -> Vehicles up to modification year 22/2 Reason for change Complaint DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button Note: Vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "Engaging park position P," for additional instructions. Cause Possible causes: 1. 2. Contamination/ingress of dust Short circuit due to ingress of water Remedy Clean printed circuit board under plastic housing and button "P": 1. 2. 3. 4. 5. 6. 7. 8. Remove DSI (AR27.60-P-0901FRX) Remove housing of DSI (see picture 1) Remove cover around "P" button above printed circuit board (see picture 2) Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) Check "P" button: Water residues and/or contamination (cf. picture 4) Carefully clean the affected areas (using contact cleaner) Reassemble and check the functionality If fault code still present after rework -- open TIPS Case NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of ve16.04.2024 17:52 © Copyright Mercedes-Benz AG CCUSHWA Page 1 / 2 hicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way. Attachments File Description Bilder Abhilfe Mittelschaltung DSI.pdf Photos of Direct Selection Interface & Circuit Board WIS-References Document number Title Note AR27.60-P-0901FRX Remove DSI center gearshift Remove DSI center gearshift Symptoms Power transmission > Automatic transmission > Drive position selection > Function > Gear cannot be engaged Control unit/fault code Control unit Fault text N150 - DIRECT SELECT interface (DSI) (DSI290) P085015 - The button 'Gear range P' has a malfunction. There is a short circuit to positive or an open circuit. P085011 - The button 'Gear range P' has a malfunction. There is a short circuit to ground. Operation numbers/damage codes Op. no. Operation text 16.04.2024 17:52 © Copyright Mercedes-Benz AG Time CCUSHWA Damage code Note Page 2 / 2