No. 06-09-3
Service Bulletin Details
Public Details for: No. 06-09-3
Technical information for evaluating overspeed events on the cayenne
- 2024 - 2023 - 2022 - 2021 - 2020 - 2019 - 2018 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 - 2008 -
Models from 2024
2024 PORSCHE CAYENNE GTS |
2024 PORSCHE CAYENNE S |
Models from 2022
2022 PORSCHE CAYENNE GTS |
2022 PORSCHE CAYENNE S |
Models from 2021
2021 PORSCHE CAYENNE GTS |
2021 PORSCHE CAYENNE S |
Models from 2020
2020 PORSCHE CAYENNE S |
2020 PORSCHE CAYENNE TURBO |
Models from 2019
2019 PORSCHE CAYENNE S |
2019 PORSCHE CAYENNE TURBO |
Models from 2018
2018 PORSCHE CAYENNE S |
2018 PORSCHE CAYENNE TURBO |
Models from 2016
2016 PORSCHE CAYENNE GTS |
2016 PORSCHE CAYENNE TURBO S |
Models from 2015
2015 PORSCHE CAYENNE S |
2015 PORSCHE CAYENNE TURBO |
Models from 2014
2014 PORSCHE CAYENNE GTS |
2014 PORSCHE CAYENNE S |
2014 PORSCHE CAYENNE TURBO |
2014 PORSCHE CAYENNE TURBO S |
Models from 2012
2012 PORSCHE CAYENNE S |
2012 PORSCHE CAYENNE TURBO |
Models from 2011
2011 PORSCHE CAYENNE S |
2011 PORSCHE CAYENNE TURBO |
Models from 2009
2009 PORSCHE CAYENNE GTS |
2009 PORSCHE CAYENNE S |
2009 PORSCHE CAYENNE TURBO |
2009 PORSCHE CAYENNE TURBO S |
Models from 2008
2008 PORSCHE CAYENNE GTS |
2008 PORSCHE CAYENNE S |
2008 PORSCHE CAYENNE TURBO |
2008 PORSCHE CAYENNE TURBO S |
Service Technical Information 6/09 ENU 0335 0 Vehicle Analysis Log: Evaluating Overspeed Events (Cayenne) (6/09) Vehicle Type: Cayenne S/Cayenne GTS/Cayenne Turbo/Cayenne Turbo S Model Year: As of 2008 Concerns: Evaluating overspeed events using the Vehicle Analysis Log (referred to below as “VAL”). Situation: Damaged unit parts due to high engine speed. The information below is intended to help you to evaluate engine damage, which may occur as a result of one or more overspeed events. You can also use the values entered in the VAL to improve the assessment process for granting pre-owned car warranties, for example, and to examine entitlements for carrying out repairs under warranty. Engines are designed to operate at a maximum permitted speed. This engine speed is not exceeded when the vehicle is driven normally. However, driving and operating problems (e.g. “changing to the wrong gear” on vehicles with manual transmission) or manipulation (e.g. tuning) can cause the maximum permitted engine speed to be exceeded when the vehicle is driven. Overspeed events are stored in the DME control unit. The following values are also recorded: - Number of ignition attempts in each overspeed range 1 , and, - Status of the hourmeter during the last overspeed event 2 . 1 Overspeed range = Defined rev ranges with classification of expected engine damage, e.g. engine damage possible, ... probable, ... very probable, engine damage has generally occurred; see section 'Rev ranges'. 2 For technical reasons, overspeed events are entered in a preset time interval. As a result, there may be entries in a higher rev range (e.g. range 2), while no entries are stored in the lower range. Typical faults and symptoms as a result of overspeed events may include the following: • • • • • • • • • • • • Damaged valves and/or pistons (impact marks on the valve, valve impressions on the piston, valve bent). Cylinder liner damage (even “piston seizure”). Damaged or displaced connecting rod bearings. Loosened or loose fastening screw(s) on the crankshaft pulley. Loosened or loose fastening screw(s) on the camshaft gear. Loosened or loose connecting rod bolts. Cracked timing chain(s). Changed timing. Irreparably damaged clutch elements (pressure plate and/or drive plate). Vibrations and/or engine imbalance due to irreparably damaged clutch elements. Vibrations around the transmission. Defective synchronization. AfterSales Apr 10, 2024 Page 1 of 2 0 Service 0335 ENU Technical Information 6/09 Information If such faults or symptoms are present together with engine damage, the VAL that was created must be checked for overspeed entries. If overspeed entries are found and if the difference between the current hourmeter and the status when the last overspeed event was recorded is less than 50 operating hours, there is a high probability that the damage was caused by overspeed event(s). The value “50 operating hours” should be seen as a guide. The possibility of engine damage occurring much later due to previous overspeed event(s) cannot be ruled out. Rev ranges 9PAII: Create the VAL before deleting the fault memory. Overspeed events are documented as follows in the VAL: Rev range 1: 6,700 -1 ... to 6,900 -1 Maximum permitted engine speed exceeded; engine damage possible. Rev range 2: 6,900 -1 ... to 6,950 -1 Maximum permitted engine speed exceeded; engine damage possible. Rev range 3: 6,950 -1 ... to 7,000 -1 Maximum permitted engine speed exceeded; engine damage possible. Rev range 4: 7,000 -1 ... to 7,150 -1 Maximum permitted engine speed clearly exceeded; engine damage probable. Rev range 5: 7,150 -1 ... to 7,200 -1 Maximum permitted engine speed very clearly exceeded; engine damage very probable. Rev range 6: over 7,200 -1 Engine damage has generally occurred. Information Before starting engine repairs or granting a pre-owned car warranty: In the event of overspeed events in range 4 – 6, we recommend that you contact the Technical Hotline before starting repairs or granting a pre-owned car warranty in order to find out how to proceed and verify warranty coverage References: Workshop Manual '03350003 Creating Vehicle Analysis Log (VAL)' → “After Sales News 11/2007” and “Porsche Aktuell”: PIWIS Tester: Function for returning Vehicle Analysis Logs (VALs) Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed. © Porsche Cars North America, Inc. 2024 Apr 10, 2024 Page 2 of 2 AfterSales