Bmw 325 1993

• Recall 16741 [USA]: Consequence of non-compliance: in the event of an accident, the occupant will be subjected to an increased risk of injury.
  In a fmvss no. 208 30 miles-per-hour compliance test, an unbelted test driver dummy's chest maximum resultant acceleration was 70.8 g's, which exceeds the maximum allowable value of 60 g's. Also, the unbelted passenger dummy's left femur maximum load was 2361 lbs, which exceeds maximum allowable value of 2250 lbs. The vehicles do not comply with fmvss no. 208, "occupant crash protection."
  on automatic transmission models only, the dealer will replace the transmission support crossmember with a crossmember used on the manual transmission model. Also, the transmission rear bushing supports will be replaced with bushing having different performance characteristics. The steering column front support bearing at the firewall will be replaced with a modified part using a teflon inner surface and teflon spray will be applied to the column housing in the area of the bearing. A brace will be added between the knee bolster support and the steering column.
  system: interior systems; passive restraints; air bag; driver; fmvss n0. 208.Vehicle description: passenger cars, models 325i, 325ia, 325is, 325sa, and m3.Note: if your vehicle is presented to an authorized dealer on an agreed upon service date and the remedy is not provided free of charge within a reasonable time or the remedy does not correct the noncompliance, please contact bmw service center at 1-800-831-1117. Also, contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

  Show Content

• Recall 18656 [USA]: Fuel seepage between the feed fuel hose and the engine fitting can result in free fuel in the engine compartment, which could result in a fire when exposed to a source of ignition.
  Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.
  a redesigned feed fuel hose and hose clamp will be installed to alleviate the fuel seepage.
  system: fuel; fuel line fittings; metallic.Vehicle description: passenger vehicles; models 318i, 318si, 318ic, 325i, 325is, 325ix, 325ic, 525i, 535i, 735i and 735il.Note: if your vehicle is presented to an authorized dealer on an agreed upon service date and the remedy is not provided within a reasonable time and free of charge, or the remedy does not correct the defect or noncompliance, please contact bmw at 1-800-831-1117. Also, contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

  Show Content

• Recall 20427 [USA]: Vehicles operated under this increased cooling systempressure condition can suffer damage or failure of parts of the cooling systemsuch as (1) leakage from a coolant hose, (2) leakage of the radiator orexpansion tank, (3) disconnection of a hose from a pipe or a fitting, and (4)cracks in the heater core end piece resulting in coolant leakage. in some cases,boiling coolant can contact the lower right leg of the driver resulting inburns. also, escaping coolant in the passenger compartment can cause vaporfogging of the interior surface of the windows, reducing driver visibility.
  The malfunction or failure of a coolant system component results in significantly increased coolant temperature and a resulting increase in system pressure.
  dealers will install a thermostatic bypass valve in the engine compartment to control coolant temperature in the heater core. Also, a new design radiator cap will be installed, to control pressure and provide greater coolant overflow in the event of overheating.
  system: coolant system.Vehicle description: passenger cars.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Air bag wiring failure investigation # EA95013

  There is no summary currently available
  

  Show Content

325is - two rear subframe mounts have completely broken. There is no evidence of abuse/accident. Repair estimates have been written in the $2500-$4000 range. After researching the matter i've found that many others have encountered the problem. I even spoke to a bmw body shop employee who believes it should have been recalled. I also found another 93 325is owner in san francisco who was able to get bmw of north america to repair his car (out of warranty) at no cost. I'm currently working with bmwna and my local dealer to achieve the same thing.

Recalls # 94v15100 and 96v11100; never received notice from manufacturer about either recall, and no response, just a referral to dealership. *ak

The vehicle was in a severe frontal collision which involved a roll over and the airbag did not deploy.Please describe. *ak

Vehicle was in a front-end collision and driver's air bag did not deploy. Please describe. *ak

Gasoline odor persists even after replacement of gas tank/fuel lines as per recall. (94v066000) *dsh

Sunroof rattles at 70 mph.

Driving electrical problem developed.Resulting in vehicle fire. Tt

Noisy front windows.

Passenger's front door panel keeps popping off at top. *ak