Bmw K1200r 2006
Vehicle Details: Recalls
Below you will find all available information on the 2006 BMW K1200R.
Manufacturer | Known WMI(s) | Fuel Type |
---|---|---|
BMW |
Use the box here to look up VINs from BMW as well as other manufacturers
Recall 2020437 [Canada]: Fuel supply
Issue: on certain motorcycles, the fuel pump flange could crack. If this happens, fuel could leak while the engine is running. Note: this recall only affects motorcycles that did not have the fuel pump replaced under transport canada recall 2013-442. Safety risk: a fuel leak can create the risk of a fire. Corrective actions: bmw will notify owners by mail and instruct you to take your motorcycle to a dealer to replace the fuel pump and auxiliary fuel pump (if equipped) with an improved version.Recall 2017428 [Canada]: Lights and instruments
Certain motorcycles with dealer installed accessory turn signals may not comply with the requirements of canada motor vehicle safety standard (cvmss) 108 - lighting system and retroreflective devices. The size of the lens on the accessory turn signals may be too small, and therefore would not meet the requirements of the standard. This could reduce vehicle conspicuity to following and approaching road users, and increase the risk of a crash causing injury and/or property damage. Correction: dealers will replace the accessory turn signals with factory indicators that meet the requirements of the standard.Recall 2015101 [Canada]: Powertrain
On certain motorcycles, the threaded holes on the rear wheel flange could crack if the wheel bolts are tightened beyond the specified torque limit during servicing. Over time, this could allow the bolts to back out of their threaded holes, causing the rear wheel to become loose. This could result in a loss of stability of the motorcycle, and increase the risk of a crash causing injury and/or property damage. Correction: dealers will replace the aluminum rear wheel flange with a steel flange.Recall 2013442 [Canada]: Fuel supply
On certain motorcycles, cracks could develop in the fuel pump and/or auxiliary fuel pump flange (if equipped). This would result in fuel leaking when the engine is turned on and the fuel system is pressurized. Leaking fuel, in the presence of an ignition source, could lead to a fire causing injury and/or damage to property. Correction: dealers will inspect the fuel pump flange(s) and install a reinforcing ring or replace the fuel pump(s), as necessary.Recall 2012334 [Canada]: Brakes
On certain motorcycles, vibration, particularly on a long ride at constant high engine rpm and on engine overrun at high rpm, can, under certain circumstances, cause foaming of the brake fluid in the reservoir of the front brakes. This foaming may cause air to enter into the brake system, which can severely diminish the braking efficiency of the front brakes. Extended stopping distance may result in a vehicle crash causing property damage and/or personal injury. Correction: dealers will install a screen insert into the front brake fluid reservoir.Recall 2010395 [Canada]: Suspension
On certain motorcycles, due to environmental conditions, the bearings of the link lever attached to the rear strut could be subject to corrosion. This could lead to reduced movement of the link lever. Over time, if the corrosion became significant, restriction of movement of the link lever could occur. This could affect handling of the motorcycle. In an extreme case, this could result in the connecting rod breaking by a bending force, causing the rear wheel to decelerate by contact with the inner fender. This could lead to a crash depending on traffic, road conditions and rider's reactions. Correction: dealers will replace the rear suspension relay lever.Recall 2007019 [Canada]: Engine
On certain motorcycles, frequent short-trip usage, particularly at low ambient temperatures, causes condensation, increasing the proportion of water in the engine oil. The water vapour produced while the engine is running condenses at the outlet port of the dry-sump oil tank breather. If temperatures are below 0 degrees celsius, the condensation can freeze and plug the breather line of the oil tank. As a result, oil tank over-pressurization can cause the tank to rupture, allowing oil to escape onto the rear wheel and create the risk of a crash causing injuries or death. Correction: dealers will install an updated oil cap with a pressure relief valve.Recall 2006118 [Canada]: Brakes
Certain motorcycles may exhibit a temporary loss of abs function as a result of an "overpressure" effect in the brake system caused by applying significant force to the brake lever under rapid, repeated and unusually harsh braking. Loss of abs function can increase the risk of a crash in certain traffic and road conditions. Correction: dealers will install a banjo bolt with a flow restrictor to the front brake line.Recall 2006249 [Canada]: Brakes
On certain motorcycles, the integral anti-lock brake system (iabs) cable may have been damaged during vehicle assembly. If this is the case, the cable may contact the front forks which could result in a loss of abs function. Correction: dealers will replace the iabs sensor cable.
To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.