Dodge Caravan C/v 1991

• Recall 10653 [USA]: Personal injury could occur if the bolts break allowing the liftgate to fall suddenly.
  Vehicle description: mini vans. The bolts used to attach the strut to the body and the rear liftgate can accumulate fatigue damage if three factors combine. If the bolt is loose, the gas strut is over-pressurized, and the frequency of opening and closing cycles is higher than for the average customer, the bolt can fail.
  dealers will inspect for loose fasteners, if the fasteners are loose, the strut (and integral bolts) will be replaced. If the bolt shows evidence of torque, the bolt will be removed, larger washers will replace the existing washer and the bolt will be reinstalled and hand tightened to the target torqued.
  owner notification began during august 1999. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-992-1997. Also contact the national highway traffic safety administration's auto safety hotline at 1-888-327-4236.

  Show Content

• Recall 10249 [USA]: This could allow the drive arm to disengage from the shaft leading to a loss of wiper function. the driver's visibility would be impaired, increasing the risk of a crash.
  Vehicle description: minivans. The left hand windshield wiper pivot drive arm was not mechanically staked to the pivot shaft.
  dealers will replace the left hand side windshield wiper pivot assembly.
  owner notification began march 27, 2000. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-992-1997.Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 14153 [USA]: In the event of a vehicle crash, the occupant may not be properly restrained increasing the risk of personal injury.
  Vehicle description: passenger mini-vans. Covers on the solid stalk mounted seat belt buckles can become dislodged causing the release button to stick inside the cover. The buckle would then be only partially latched.
  dealers will install a cover retaining clip to the stalk mounted buckle cover to prevent dislocation of the buckle cover.
  owner notification began december 8, 1997.Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-853-1403. Also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

  Show Content

• Recall 13507 [USA]: If the steering wheel separates from the center hub attachment to the steering column, loss of control can occur increasing the risk of an accident.
  The steering wheel armature stamping can crack and separate from the center hub attachment to the steering column.
  dealers will inspect the steering wheel for armature cracks in the center hub attachment area. Any steering wheels showing cracks will be replaced. All other vehicles will have a reinforcement plate installed to prevent steering wheel separation in the event cracking occurs.
  owner notification began december 27, 1996. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-853-1403.Also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

  Show Content

• Recall 28909 [USA]: If this condition occurs, the abs function could be lost and reduced power assist would be experienced during vehicle braking increasing the potential for a vehicle accident.
  The abs hydraulic control unit can experience excessive brake actuator piston seal wear causing pump-motor deterioration.
  dealers will test the vehicle's anti-lock brake system and repair the vehicles if necessary. Also the warranty on all abs components will be extended to 10 years or 100,000 miles (except for the brake actuator piston assembly and the pump-motor assembly which will have a lifetime coverage). Owners will also be reimbursed for previous abs component repair costs.
  system: brakes; hydraulic; anti-skid system. Vehicle description: passenger vehicles and mini-vans equipped with anti-lock brake systems (abs). Note: owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-853-1403. Also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

  Show Content

• Recall 29422 [USA]: If the liftgate latch opens, occupants can be ejected resulting in significantly increased risk of injury or death.
  Vehicle description: light duty passenger minivans without remote release. This is not a safety recall. There has been no determination that a safety defect exists with the minivan latches. Chrysler is conducting a service campaign to replace the liftgate latch assembly of the affected minivans. In a collision, the rear liftgate latch assembly could open.
  chrysler dealers will replace the liftgate latch with a new stronger latch assembly without charge. Chrysler began notifying owners of these vehicles in october 1995.
  this is not a safety recall. There has been no determination that a safety defect exists with the minivan latches.However, chrysler has decided to provide a stronger latch without charge.Owners can contact chrysler at 1-800-minivan (1-800-646-4826).

  Show Content

• Recall 21642 [USA]: Fluid leakage eventually causes the loss of both theanti-lock brake system and hydraulic assist for the brake system, resulting inincreased likelihood of brake lockup and increased stopping distances, whichcould result in a vehicle accident.
  The anti-lock brake system high pressure pump may be porous which will result in brake fluid leakage.
  replace the abs high pressure pump and high pressure hose if the last six digits of the bar code label on the pump are between 052300 and 059262.
  system: brakes; abs system.Vehicle description: passenger mini-vans with anti-lock braking systems (abs).Note: see also nhtsa campaign no. 91v191000.

  Show Content

• Recall 21751 [USA]: Fluid discharge eventually causes the loss of both theanti-lock brake system and hydraulic assist for the brake system, resulting inincreased likelihood of brake lockup and increased stopping distances, whichcould result in a vehicle accident.
  The anti-lock brake system high pressure hose may leak or detach at its crimped end fitting resulting in the discharge of hydraulic fluid.
  replace the abs high pressure hose with a hose of different design and construction.
  system: brakes.Vehicle description: passenger cars and vans with anti-lock brake systems (abs).

  Show Content

• Recall 21666 [USA]: Inoperative turn signal lamps would not inform driverthat a lamp was out, or warn other drivers of intent to turn, creating a riskof accident; vehicle does not comply with fmvss 108.
  Incorrect turn signal flasher inhibits indication of signal lamp outage.
  replace turn signal flasher with proper flasher.
  system: turn signal flasher; fmvss 108.Vehicle description: commercial vans.

  Show Content

• Recall 1999145 [Canada]: Visual system
  On certain vehicles, the left hand windshield wiper pivot drive arm was not mechanically staked to the pivot shaft. This may allow the drive arm to disengage from the shaft and lead to a loss of wiper function. Correction: the left windshield wiper pivot assembly will be replaced with one that incorporates an improved mechanical connection of the drive link to the pivot shaft.

  Show Content

• Recall 1997104 [Canada]: Structure
  A combination of no bolt torque, high pressure in the strut and a severe duty cycle can create the potential for the liftgate strut attaching bolts to separate. This could result in injury to persons standing under the liftgate at the time of failure. Correction: liftgate struts will be inspected for loose fasteners. If fasteners are loose, the strut (and integral bolts) will be replaced. If the bolt shows evidence of torque, the bolt will be removed, large washers will be installed and bolt will be torqued to specification.

  Show Content

• Recall 1997162 [Canada]: Seats and restraints
  The first row rear seat outboard side seat belt anchor hook can become unattached from the body anchor position. Also, the covers on solid stalk mounted seat belt buckles may become dislodged. Should a cover become dislodged, the release button may stick inside the cover creating the potential for the buckle to become partially latched. In the event of a vehicle crash, either of these conditions could result in the occupant not being properly restrained. Correction: anchor hook retaining clip will be replace with a revised profile clip and cover plate. Dealers will also install a cover retaining clip to the stalk mounted buckle cover to prevent dislocation of the buckle cover.

  Show Content

• Recall 1996063 [Canada]: Brakes
  Note: vehicles equipped with bendix-10 antilock brake system (abs) vehicles with abs brakes may experience premature actuator piston seal wear in the abs hydraulic control unit and/or actuator pump motor deterioration. If this occurs, the abs function may be lost and reduced power assist may be experienced during vehicle braking. Correction: vehicles with abs malfunction will be repaired as necessary. Warranty on all abs components will be extended to 10 years or 160,000 km (except for the brake actuator piston assembly and the pump-motor assembly which will have lifetime coverage).

  Show Content

• Recall 1996198 [Canada]: Steering
  The steering wheel armature stamping may crack and separate from the centre hub of the steering column. This could adversely affect steering control and result in a possible crash without prior warning. Correction: steering wheels exhibiting cracks will be replaced. All other involved vehicles will have a anti-separation plate installed to prevent separation of the steering wheel from the steering column.

  Show Content

• Recall 1991046 [Canada]: Lights and instruments
  These vehicles do not comply with c.M.V.S.S. 108 - lighting. Signal flasher inhibits signal lamp outage indication in the event of a signal lamp failure. Correction: turn signal flasher will be replaced with the correct flasher.

  Show Content

• Recall 1991157 [Canada]: Brakes
  On certain vehicles equipped with an anti-lock brake system (abs), the high pressure hose may leak or detach due to inadequate crimping of the hose-to-end fittings. This condition could result in loss of brake power assist and a possible increase in stopping distances. Correction:(526) abs high pressure hose will be replaced with a hose of different design and construction. (527) four hundred and twenty six of the identified mini vans will also have the abs pump casting inspected for porosity. Leaking pumps, if found, will be replaced.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Rear liftgate support investigation # RQ99004

  The liftgate support attaching bolts may break.This could result in the liftgate falling unexpectedly which may injure someone standing under it.
  

  Show Content

• Safety belt anchorage failures investigation # EA97005

  There is no summary currently available
  

  Show Content

• Alleged rear liftgate support failure investigation # EA96027

  The retainer bolt of the rear liftgate support cylinders may shear resulting in sudden collapse of the rear hatch door.
  

  Show Content

• Inconsistent safety belt buckle investigation # EA96016

  Safety belt buckle hosing slips down, pinching the red release button.Owners report having trouble opening and closing them many allege belt unlatches while driving because of the release buttom
  

  Show Content

• Throttle will not return to the position investigation # PE96036

  Uncontrolled engine speed condition results fro throttle shaft binding
  

  Show Content

• Alleged rear liftgate support failure investigation # PE96035

  The retainer bolt of the rear lift gate support cylinders may sheer resulting in the sudden collapse of the rear hatch door.
  

  Show Content

• Safety blt latch operation investigation # PE96008

  There is no summary currently available
  

  Show Content

• Steering wheel separation investigation # EA95029

  After an extensive investigation and analysis, chrysler has identified the defect as a fatigue failure, origination in the heat affected region of the "projection welds" of the steering wheel "hub" to steering wheel "armature" attachment.The hub is the portion of the steering wheel assembly that connects it to the steering column shaft and is attached to the underside of the steering wheel assembly by 4 welds.If cracks develop in the heat affected region of the welds and propagate through the steering wheel armature to each of the welds, the steering wheel can separate from the hub.This is a slow progressive failure which normally occurs at high mileage.In some cases complainants have reported a looseness or wobbling of the steering wheel prior to separation.To remedy this defect, chrysler will inspect the steering wheels of the affected vehicles for cracks in the hub area.If any cracks are found, the steering wheel will be replaced.All other vehicles will have reinforcing plates installed which would prevent a steering wheel separation should cracking occur.
  

  Show Content

• Abs braking system fails investigation # EA94028

  There is no summary currently available
  

  Show Content

• Liftgate latches investigation # EA94005

  There is no summary currently available
  

  Show Content

• Melted throttle cables investigation # PE93056

  There is no summary currently available
  

  Show Content

• Window shattering investigation # PE92053

  There is no summary currently available
  

  Show Content

• Safety blt anchorage brks investigation # PE92028

  There is no summary currently available
  

  Show Content

• Braking performance loss investigation # PE91094

  There is no summary currently available
  

  Show Content

• Abs control failure investigation # PE91093

  There is no summary currently available
  

  Show Content

Started missing at frist, then a no start. I've changed the timing chain, crank sensor, camshaft sensor, coil pack. Tried a new ecm. There's voltage to the coil pack, but no spark. I've checked wiring circuit, and auto shut down relay .

Tl* the contact owns a 1991 dodge caravan. The contact stated that the front brake calipers malfunctioned and made the vehicle difficult to move. The vehicle was taken to the dealer, who diagnosed that the hydraulic control unit that houses the brake actuator piston and the pump motor assembly needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was informed that the vehicle was not covered under the nhtsa campaign number 96v099000 (service brakes, hydraulic) although the recall indicated that the part would have a life time coverage. The failure mileage was 87,000.

The drivers side airbag deployed while i was driving down the road, my arm is swollen, burned, and bruised. My nose and head have hurt for the last four days. *tr

Dt*: the contact stated recall # 96v099000 for the service brakes: hydraulic: anti-lock was received. When the service dealer was called to schedule the recall repair, the service dealer informed the contact, there would be charges for replacing the accumulator plus labor costs. The manufacturer requested the receipts to be sent for review for possible reimbursement. Updated 01/10/07. *jb

A loud clunking noise could be heard when traveling over uneven road surfaces or on right hand turns. After completing a right turn, the driver side front wheel was completely dislodged and folded backinto the wheel well. The lower control arm was fractured where the ball joint was seated, allowing the ball joint to come away from the lower control arm. The driver side drive shaft was dislodged from the transmission. *tr

1991 dodge caravan. Consumer writes in regards to anti lock brake system recall and seeks reimbursement for repairs. *smd the consumer stated he paid for the repairs on april 20, 2006 and was charged $376.73, even though a recall had been issued. The consumer experienced abs problems again in december 2013. The consumer stated the recall letter stated if the problem occurred again, chrysler would cover any repairs. The dealer informed the consumer, he had to pay $112 for a diagnostic test, to see if the problem would be covered, under the recall. The dealer then informed the consumer, they didn't have the equipment to test his vehicle, due to the age. However, a few days later, the dealer informed the consumer, they had the equipment, but it would cost $336. The consumer declined the test. Also, the transmission, starter, fuel pump, ignition coil blocks , serpentine belt, pulleys, power steering pump, and radiator were all replaced. *jb updated 04/16/14

Hello below is a copy of text on your recall site with details of this recall comments i make are below that.. Make : dodge model : grand caravan year : 1991 manufacturer : chrysler corporation nhtsa campaign id number : 96v099000 mfg's report date : apr 19, 1996 component: service brakes, hydraulic:antilock potential number of units affected : 321000 summary: the abs hydraulic control unit can experience excessive brake actuator piston seal wear causing pump-motor deterioration. Consequence: if this condition occurs, the abs function could be lost and reduced power assist would be experienced during vehicle braking increasing the potential for a vehicle accident. Remedy: dealers will test the vehicle's anti-lock brake system and repair the vehicles if necessary. (except for the brake actuator piston assembly and the pump-motor assembly which will have a lifetime coverage). The thing i find here is the term regarding piston assembly when i took my van in due to failure only the piston assembly was replaced it should be revised to include the whole unit because a accumulator made of cast iron that is connected to the unit is never replaced rust keeps entering the unit from this accumulator being it is made of a rusting metal and just keeps making the unit fail this is my second repair in 2yrs and the rust is now getting into the lines causing the rear wheels to lock in wet weather all the parts stores that even carry the unit which is few sell it as a complete unit not in pieces such as with other master cly. 's without abs i find cast iron a poor choice for a air tank of a air pump which by nature injects air into the metal cast iron tank stainless steel would been a better choice if it would meet the tank pressures. I am seeking replacement of the entire brake system since it is now a total loss due to the rust and prefer non abs if that's able . *nm

Dt*: the contact stated recall work was performed on the vehicle prior to the contact being aware of the recall. The manufacturer was contacted about reimbursement which they denied because the recall work was not performed at an authorized dealership. The nhtsa recall # 96v099000 concerning the service brakes: hydraulic: antilock.

Dt*: the contact stated there is a vibration in the front end and the brake pedal is pulsating. This has persisted for 3 years. The tires were replaced and realigned numerous times to correct the vibration, however the problem still occurs. The brakes were replaced 3 times, although the pulsating is currently evident. The vibration occurs around 30 mph. When the vehicle speed increases, the vibration is less noticeable. The manufacturer has not been contacted. *nm