Dodge Stratus 1998

• Recall 84376 [USA]: If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
  Federal-mogul is recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
  federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on january 28, 2011. Owners may contact federal-mogul at 1-877-489-6659.
  this recall only pertains to replacement control arm assemblies and has no relation to any original equipment installed on vehicles manufactured by chrysler llc.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 68278 [USA]: Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
  Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, d10945, d10946, g10945, and g10946. The affected control arms, d10945 and d10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The g10945 and g10946 are the same part as the d10945 and d10946 respectively. They are labeled differently depending on the aftermarket customer.
  qualis automotive will replace the ball joints free of charge. The safety recall began on november 9, 2009. Owners may contact qualis automotive at 1-800-493-4128.
  this recall only pertains to aftermarket ball joints and has no relation to any original equipment installed on vehicles produced by chrysler.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 67077 [USA]: This condition may result in a vehicle fire.
  Import products is recalling 30,351 fuel filters sold to and branded by the affinia group as carquest p/n 86523, napa p/n 3523, and wix p/n 33523 for use as replacement equipment on the vehicles listed above. These filters may develop a leak in the hose assembly and/or connectors due to improperly adhered line connectors.
  the affinia group will notify owners and the filters will be replaced free of charge. The safety recall began on august 1, 2009. Owners may contact wix filter return center at 1-704-869-7411 or import products at 1-508-279-8207.
  this recall only pertains to affinia group aftermarket fuel filters and has no relation to any original equipment installed on the listed passenger vehicles.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 37166 [USA]: Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.
  Certain tigas fuel pump modules manufactured between june 1 and september 24, 2006, sold under various brand names and p/nos. These fuel pump modules are sold as aftermarket for use in certain daimlerchrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.
  ti automotive will notify owners and replace the defective fuel pump modules free of charge. The recall began on october 6, 2006. Owners may contact ti automotive toll-free at 1-877-461-1834.
  this recall only pertains to aftermarket fuel pump modules and has no relation to any original equipment installed on vehicles by daimlerchrysler.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 41974 [USA]: Either circumstance may result in the vehicle rolling away without warning.
  On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
  dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. Owner notification began on june 14, 2004. Owners should contact daimlerchrysler at 1-800-853-1403.
  daimlerchrysler recall no. C45.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 8513 [USA]: Daimlerchrysler recall no. 843. if this happens, the tube could leak, reducing the effectiveness of one-half of the diagonally split braking system, and resulting in longer stopping distances.
  Vehicle description: passenger vehicles. The right rear brake tube can contact the exhaust system clamp and wear a hole in it.
  dealers will inspect the brake tubes for visible evidence of contact with the exhaust system clamp. If the tube shows evidence of contact, it will be replaced. If no evidence of contact exists, the tube will be fastened with a clip.
  owner notification began november 22, 1999.Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact daimlerchrysler at 1-800-992-1997. Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 14241 [USA]: If this happens, the "ignition-park" interlock system will be nonfunctional.
  Vehicle description: passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key can cause a trapped key condition which can result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, can break the connecting pin in the shifter.
  dealers will inspect for proper operation of the system. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a "self-adjusting" design.
  owner notification began october 26, 1998. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-992-1997.Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 2004003 [Canada]: Other
  On certain vehicles equipped with an automatic transmission and a floor-mounted shifter, the ignition-park interlock may become defeated and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position. This may result in the vehicle rolling away without warning. Correction: dealer will inspect the function of the ignition-park interlock system. Vehicles found with functional interlock systems will have a load-limiting push rod installed into the floor shifter lever. Vehicles with a non-functional ignition-park interlock system will have the shifter assembly replaced.

  Show Content

• Recall 1999009 [Canada]: Emissions
  On certain vehicles, incorrect weld wire, in combination with the stainless steel shell of the catalytic converter, will cause rusting at the weld joints and premature failure to the converter assembly. Correction: dealers will replace the catalytic converter.

  Show Content

• Recall 1999170 [Canada]: Brakes
  On certain vehicles, the right rear brake tube may contact the exhaust system clamp causing wear. If this happens, the brake tube could develop a leak, reducing the effectiveness of one half of the diagonally split braking system. This could result in longer stopping distances and a possible crash without prior warning. Correction: brake tubes will be inspected for evidence of contact with the exhaust clamp and replaced if necessary. If no evidence of contact exists, the tube will be secured with a clip.

  Show Content

• Recall 1998165 [Canada]: Other
  Note: vehicles equipped with a floor mounted automatic transmission shift lever. A combination of applying a mis-adjusted shifter release button with a low force attempt to shift out of park with the key in the locked position may break the connecting pin in the shifter. If this happens, the "ignition-park" interlock system will not function. Correction: the console shift interlock mechanism will be inspected for proper function. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a current production "self adjusting" design.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Auto trans ignition-park interlock investigation # EA03011

  The manufacturer reports above are based on daimlerchrysler¿s (dc) analysis of model year (my) 1998 (population = 356,384) and 1999 (population = 486,948) ja, jx and lh family subject vehicle data (earlier mys excluded).The population number includes all mys.The precise number of duplicates between odi and dc reports cannot be determined due to missing or incomplete information.The fatality incident involved an elderly person who attempted to stop a roll away vehicle and received fatal injuries.Odi also gathered information on my 1997-99 prowler vehicles in this investigation. The prowler vehicles were manufactured with a different design shifter mechanism (the shift lever is shorter).There are no complaints of prowler interlock failure in odi¿s database, and dc has received no reports either.The prowler is excluded from the recall scope.The investigation involved a condition where the interlock system could fail (or be made inoperative by the operator) during vehicle use, possibly inadvertently.The interlock system is required under fmvss 114.With the transmission in the park position and the ignition key off, the combined action of pressing the shift button and pulling the shift lever rearward may result in the operator overcoming the interlock system and cause the mechanical linkage of the system to disconnect.When this occurs, there is no overt indication to an operator that the system is defeated, and an increased risk of vehicle roll-away exists.Under recall 04v021, dc will replace damaged shift mechanisms, and will install on all vehicles a device which inhibits the operator¿s ability to overcome the interlock and defeat the system.Beginning with my 2000, dc incorporated a brake and transmission shifter interlock (btsi) system into the subject vehicles.Introduction of btsi involved design changes to the shift mechanism, one of which resulted in reduced mechanical advantage (rma) of the shift button.The rma shifter requires increased forces to overcome the interlock system, making the shifter less susceptible to damage.
  

  Show Content

• Safety belt cinching latch plate investigation # PE02082

  There are no injuries or fatalities associated with this alleged defect.While conducting this investigation, odi found that the subject cinches meet the load bearing requirements of federal motor vehicle safety standard 208, and that many of the reported failures were due to incorrect child safety seat installations. Additionally, the report rate is low (1.60/100k).The information available fails to establish the existence of a defect trend at this time.Further allocation of agency resources to this issue is unwarranted and the preliminary evaluation is being closed.
  

  Show Content

Left front upper ball joint broke

First horn was blowing out of control, than the engine we got it fixed, or so we thought ,than got the starter fix drove it 2 weeks and now it turns over but does nothing so it's sitting in my yard not working and am sick of it so far i have paid out over a grand and this car don't work just why,oh god just why.I have paid some of everything you think of one that car i have had it towards so much state farm wanted to cancel my insurance, okay let's begin.Starter replaced,eg road valve senser,valley + pipe, ignition coil,ignition relay,temperature senser,ignition wire, rotor, injector, brush, bearing ball, december frame not to mention the labor my god. And now it sits in my yard am tired really.

The abs and the braking system quit working i got on the freeway and i had breaks by the time i got three off ramps later to get off the freeway i had no brakes they didn't work in the pedal went all the way to the floor causing and accident

Having issues with dash and headlight dimming,also radio goes off and looses memory,door locks won't work when radio goes off. Burnt out defogger relay and power amp fuse with no power amp, also had to replace horn relay yet taking all those relays out and problem still happens. Already checked lighter assembly, that was popping amp fuse. Fixed that still happening. Also goes through 1 quart of oil a month but no leaks under the car when moved. ?????? Help!!!!!! The oil problem should fall under hazardous meterials act if all these cars are dumping used oil all over this country.

Tl* the contact owns a 1998 dodge stratus. While performing an oil change, the contact noticed that the lower ball joint and control arms were rusted. The contact stated that the lower ball joints and control arms were replaced four months ago. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was 74,000.

Tl* the contact owns a 1998 dodge stratus. The contact stated that the gear shifted from park without the key in the ignition. The contact also stated that the key became stuck in the ignition. The failure occurred on multiple occasions. The contact referenced nhtsa campaign id number: 04v02100 (power train), however, the vehicle was not affected at the time and no repairs were done. The manufacturer was notified of the failure. The approximate failure mileage was 50,000.

Tl* the contact owns a 1998 dodge stratus. While the vehicle was at the dealer for routine maintenace, it was discovered that the front ball joint and control arm needed to be replaced. The vehicle was repaired. The manufacturer was not made aware of the failure. On two separate occasions, the vehicle failed to start. The vehicle was taken to the dealer for diagnostic testing. The dealer determined both times that the fuel pump needed to be replaced. The vehicle was repaired both times. The manufacturer was not made aware of the failure. Several years later, the contact was unable to remove the key from the ignition switch. The vehicle was not included in nhtsa campaign numbers: 04v021000 (power train) and 98v183000 (power train). The vehicle was not repaired. The manufacturer was made aware of the failures. The failure mileage was 5,000.

I started the car, placed my foot on the brake and it went to the floor. I exited the vehicle and found a large pool of fluid on the right front of the car. Abs and brake light came on. Master cylinder was near empty. I had the car towed to my local mechanic and he found that all the brake lines (6?) were leaking at the abs pump. This is the car my wife drives. My wife! I am anal with regard to my vehicles condition and maintenance. To have a failure like this on a what is supposed to be a "quality american made vehicle" is absurd and totally unacceptable! My brothers 1999 honda, my step son's 1991 nissan stanza (recently sold) a 1993 geo prizm (i.E. Toyota corolla!!!) recently sold had zero rust on any brake fitting, brake line or fuel line. I had no brake issues previously. *kb

Tl* the contact owns a 1998 dodge stratus. The contact stated that the vehicle was parked when it ignitied into flames. The fire department was able to extinguish the fire and a fire report was filed. The fire department concluded that the fire originated from the high pressure power steering hose. The contact spoke with the manufacturer and was advised that the vehicle was not included in nhtsa recall campaign id number: 06v001000 (steering: hydraulic power assist: hose, piping, and connections) dealt with the 1999-2002 dodge stratus and not the 1998 even thought the failure was caused for the same reason. The failure mileage was 175,000.

Common OBD-II Error Codes

• P0442 [2] Evaporative Emission Control System Leak Detected (small leak)
• P0455 [2] Evaporative Emission Control System Leak Detected (gross leak)
• P0456 [2] Evaporative Emissions System Small Leak Detected
• P1494 [1] EGRCHK Solenoid Circuit Malfunction