International 4700 2001

• Recall 2002113 [Canada]: Brakes
  On certain trucks the fitting that connects the double check valve to the rear axle air brake relay valve may break. If the fitting breaks the rear service brakes will cease to operate, resulting in an extended stopping distance, possibly resulting in a collision.

  Show Content

• Recall 2002165 [Canada]: Brakes
  On certain vehicles, the trw model 410m ecu (electronic control unit) can misinterpret particular false wheel speed signals generated from any of the following conditions: an incorrect gap between the sensor and tone ring, a chaffed sensor wire, connector corrosion, sensor vibration or quality of harness and pin-outs. If one of these conditions occurs, the ecu could not distinguish between an actual low friction event on road surface and a low amplitude sensor signal and would activate the abs brakes, instead of deactivating the abs in response to a false signal. The driver would experience a hard brake pedal during the middle to end of a braking event and a decrease in deceleration at the end of the stop. The driver may experience an unexpected extended stopping distance, which could result in a collision. The abs warning indicator light may not come on to warn the driver of a system malfunction. Correction: dealer will affect repairs. Note: recall superseded by 2004171 and 2004172.

  Show Content

• Recall 2004048 [Canada]: Brakes
  On certain vehicles, the bosch zero offset pin slide (zops) hydraulic disc brakes may experience calipers sticking in the applied position, which can result in excessive or abnormal heat generation at one or more of the brakes. In bus applications, the combination of the following factors may collectively result in an unreasonable risk to motor vehicle safety: potential fire at a wheel end, high incident rates of stuck calipers, and evacuation and containment concerns relating to multiple passengers. Correction: dealers will affect repairs. This is an expansion of recall 2003053.

  Show Content

• Recall 2004172 [Canada]: Brakes
  On certain vehicles, the trw model 410m electronic control unit (ecu) can misinterpret particular false wheel speed signals generated from any of the following conditions: an incorrect gap between the sensor and tone ring, a chaffed sensor wire, connector corrosion, sensor vibration or quality of harness and pin-outs. If one of these conditions occurs, the ecu could not distinguish between an actual low friction event on road surface and a low amplitude sensor signal and would activate the abs brakes, instead of deactivating the abs in response to a false signal. The driver would experience a hard brake pedal during the middle to end of a braking event and a decrease in deceleration at the end of the stop. The driver may experience an unexpected extended stopping distance, which could result in a collision. The abs warning indicator light may not come on to warn the driver of a system malfunction. Correction: dealers will replace the abs ecu. Note: this recall supersedes recall 2002165.

  Show Content

• Recall 2004048 [Canada]: Brakes
  On certain vehicles, the bosch zero offset pin slide (zops) hydraulic disc brakes may experience calipers sticking in the applied position, which can result in excessive or abnormal heat generation at one or more of the brakes. In bus applications, the combination of the following factors may collectively result in an unreasonable risk to motor vehicle safety: potential fire at a wheel end, high incident rates of stuck calipers, and evacuation and containment concerns relating to multiple passengers. Correction: dealers will affect repairs. This is an expansion of recall 2003053.

  Show Content

• Recall 2004172 [Canada]: Brakes
  On certain vehicles, the trw model 410m electronic control unit (ecu) can misinterpret particular false wheel speed signals generated from any of the following conditions: an incorrect gap between the sensor and tone ring, a chaffed sensor wire, connector corrosion, sensor vibration or quality of harness and pin-outs. If one of these conditions occurs, the ecu could not distinguish between an actual low friction event on road surface and a low amplitude sensor signal and would activate the abs brakes, instead of deactivating the abs in response to a false signal. The driver would experience a hard brake pedal during the middle to end of a braking event and a decrease in deceleration at the end of the stop. The driver may experience an unexpected extended stopping distance, which could result in a collision. The abs warning indicator light may not come on to warn the driver of a system malfunction. Correction: dealers will replace the abs ecu. Note: this recall supersedes recall 2002165.

  Show Content

• Recall 2004048 [Canada]: Brakes
  On certain vehicles, the bosch zero offset pin slide (zops) hydraulic disc brakes may experience calipers sticking in the applied position, which can result in excessive or abnormal heat generation at one or more of the brakes. In bus applications, the combination of the following factors may collectively result in an unreasonable risk to motor vehicle safety: potential fire at a wheel end, high incident rates of stuck calipers, and evacuation and containment concerns relating to multiple passengers. Correction: dealers will affect repairs. This is an expansion of recall 2003053.

  Show Content

• Recall 2004172 [Canada]: Brakes
  On certain vehicles, the trw model 410m electronic control unit (ecu) can misinterpret particular false wheel speed signals generated from any of the following conditions: an incorrect gap between the sensor and tone ring, a chaffed sensor wire, connector corrosion, sensor vibration or quality of harness and pin-outs. If one of these conditions occurs, the ecu could not distinguish between an actual low friction event on road surface and a low amplitude sensor signal and would activate the abs brakes, instead of deactivating the abs in response to a false signal. The driver would experience a hard brake pedal during the middle to end of a braking event and a decrease in deceleration at the end of the stop. The driver may experience an unexpected extended stopping distance, which could result in a collision. The abs warning indicator light may not come on to warn the driver of a system malfunction. Correction: dealers will replace the abs ecu. Note: this recall supersedes recall 2002165.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.