Where is the 2016 MERCEDES-BENZ E-CLASS produced?
- The 2016 MERCEDES-BENZ E-CLASS is produced in Sindelfingen, Germany.
Are there recalls for the 2016 MERCEDES-BENZ E-CLASS?
- There are 47 recall(s) for the 2016 MERCEDES-BENZ E-CLASS, additional information is below.
Does the 2016 MERCEDES-BENZ E-CLASS work with Apple Carplay?
- The E-CLASS does support Apple Carplay.
NHTSA Mandated Recalls
Recall R/2017/124 [UK]: Faulty control unit may cause vehicle to perform outside specification
Where a control unit coding was updated in a workshop between 3 december 2016 and 5 december 2016 the coding may not correspond to the specification and may trigger unplanned action in the vehicle. The safety and emissions systems may not react as design intent. recall the vehicles that are likely to be affected and update the software in the corresponding control units.
Recall R/2017/041 [UK]: Short circuit may occur
The wiring to the front windscreen washers may not have been correctly routed. This may cause a short circuit and render the wipers in operative. on affected vehicles check wiring and rework where necessary.
Recall R/2017/093 [UK]: Front airbag may be deactivated
It has been identified that the front passenger seat occupancy weight sensing system control unit may have bee incorrectly installed during assembly. If the passenger seat is placed in the rear/lower position range then it can cause the pressure hose to become kinked which will reclassify the occupant as being a child seat. This will result in the front passenger airbag being deactivated and place the occupant at a higher risk of injury if the vehicle is involved in a frontal collision. recall all affected vehicles to inspect the pressure pipe. If found to be kinked then the dealer is to contact mb technical department to establish the rectification process.
Recall R/2017/159 [UK]: electric power steering motor defective
Contacts inside the electric power steering motor may not have been correctly formed. Failure of these contacts would cause the loss of power steering assistance.If this happens a warning lamp will illuminate replace the electric power steering motor on affected vehicles.
Recall R/2017/096 [UK]: Starting current limiter may overload
Where the car incurs severe engine damage resulting in the engine failing to turn over (engine seizure) and if the driver repeatedly attempts to start the engine despite the engine not cranking the very high electrical current could lead to overheating of the starting current limiter and the potential for a fire. recall the vehicles that are likely to be affected and install an additional fuse in the electrical line to the starter.
Recall R/2016/125 [UK]: Engine may lose power
The subject vehicle could unexpectedly lose drive and coast to a halt with no motive power due to a software issue in the powertrain control unit. In certain circumstances it is possible that the risk of collision is heightened. recall the vehicles that are likely to be affected and update the software of the power train control unit.
Recall R/2016/255 [UK]: Vehicle may cut out
The rear bench seat frame may impede the wiring harness connecting the fuel supply pump. This could affect fuel supply and the engine may cut out. on affected vehicles check condition of the wiring harness repair if necessary and reroute.
Recall R/2016/275 [UK]: Risk of fire
On certain 6 and 8 cylinder engine vehicles a faulty rear engine compartment panel/bulkhead may have been installed. It is therefore possible that the panel/bulkhead may contact the left exhaust catalytic converter due to insufficient clearance. If the catalytic converter is subjected to high temperatures due to heavy driving conditions i.E. Full throttle or towing then there is a risk of the rear engine compartment panel igniting and a vehicle fire ensuing. recall all affected vehicles to inspect the clearance between the rear engine compartment panel/bulkhead and the exhaust catalytic converter. If the clearance is insufficient then the rear engine compartment panel/bulkhead will be replaced.
Recall R/2017/148 [UK]: Steering power assist may deactivate
The connector on the electric power steering control unit may not be properly sealed against water entry. If water enters the control unit the power steering assistance can be lost. The steering assistance not working could increase the risk of collision. recall the vehicles that are likely to be affected and replace the plug housing of the electric power steering.
Recall R/2017/084 [UK]: Steering column switch module may become inoperative
It has been identified that the lever used to select the drive range on the steering column switch module may become inoperative due to possible damage of a circuit board. In the event of this fault occurs then manual selection of the drive range (d r n p) would no longer be possible. The auto-p function as well as the automatic parking brake will still be available as intended. During manoeuvring the vehicle may not change the drive range as intended by the driver when operating the selector lever during standstill. This could result in an increased risk of a collision/accident. recall all affected vehicles to replace the steering column switch module.
Recall R/2017/147 [UK]: Left front seat belt pre-tensioner may not meet specification
The propellant mix in certain seatbelt pre-tensioners ignitors may be incorrect. If the front seatbelt pre-tensioners are deployed the lock function of the pre-tensioners cannot be guaranteed. recall the vehicles that are likely to be affected and replace the front seatbelts that are likely to be affected.
Recall R/2017/156 [UK]: Rear seat belt pre-tensioners may fail to restrain occupants as intended
The rear seatbelt pre-tensioner ignitors may not perform as expected. This could increase the risk of injury to the seat occupants. The lock functions of the rear seatbelts are not impaired. recall the 3 400 vehicles that are likely to be affected and replace any potentially affected seatbelts with quality assured units.
Recall R/2017/177 [UK]: Airbag may not deploy correctly
The propellant mixing ratio in the igniters of the front passenger airbag assembly may not meet specification. If the airbag is required and activated it might not deploy or not completely deploy. This could increase the risk of injury to the occupants. recall the vehicles that are likely to be affected and replace the front passenger airbag assembly.
Recall R/2017/214 [UK]: Oil leak from turbocharger feed pipe.
Under certain conditions the oil feed pipe to the turbocharger may leak.Oil may contact hot components and there is a risk of fire. on affected vehicles replace the oil feed line to the turbocharger.
Recall R/2017/282 [UK]: Electrical wiring in steering assembly may be insufficiently grounded
The steering column clock spring may break. This will cause warning messages to illuminate in the instrument cluster but in extreme instances it may cause the driver's airbag to deploy. affected vehicles will be recalled to establish sufficient grounding of the steering components.
Recall R/2020/243 [UK]: Engine control unit software to be updated
Improve the vehicle emissions via software updates. update the relevant control unit?S software and if necessary replace the nox sensors.
Recall R/2019/256 [UK]: To achieve an improvement in the emissions via software updates
Improve the vehicle emissions via software updates. update the diesel engine control unit software and add a supplementary booklet for the operator's manual
Recall R/2019/304 [UK]: Software update required to improve emissions
Improve the vehicle emissions via software updates. update the diesel engine control unit software and add a supplementary booklet for the operator's manual. Check and replace nox sensor if necessary.
Recall R/2018/308 [UK]: The air conditioner housing may possibly not have been installed according to specification
The airbag control unit may be damaged. replace the air bag control unit on affected vehicles.
Recall R/2018/327 [UK]: The routing of the fuel feed hose might not meet specifications
Fuel hose might be incorrectly routed with a possibility of chaffing and leakage. check the routing of the fuel feed hose on affected vehicles and rework it if necessary.
Recall R/2019/089 [UK]: A lock nut may be cracked in the steering gear
A lock nut may be cracked in the steering gear. the electric power steering is to be checked and if necessary replaced.
Recall R/2017/299 [UK]: Seatbelt pretensioner may not operate
Due to a deviation in the suppliers production process a specific squib batch may not comply with specifications in the event of an accident during which the left hand seat belt tensioner in the rear is activated the belt may not fully retrain the occupant. on affected vehicles replace the left rear seat belt with a correct version.
Recall R/2018/253 [UK]: Faulty routing of sensor hose in front bumper may impair the function of the active hood
The function of the active hood may be impaired. check the routing of the silicone hose for the active hood and correct if necessary.
Recall R/2019/108 [UK]: A reset in the cpc control unit could occur whilst driving
The eco start-stop function may be disabled and cause the vehicle to stall. the affected vehicles are to be recalled and the software updated.
Recall R/2020/226 [UK]: Electro-chemical processes may create conductive connections inside the electric busbar
Electro-chemical processes might create conductive connections inside the electric busbar. modify the busbar and install a separate electric line on the affected vehicles.
Recall R/2019/326 [UK]: The spoiler on the rear door may have been mounted incorrectly
The spoiler on the rear door might not have been mounted according to specification. check the mounting of the rear door spoiler on the affected vehicles and rework it if necessary.
Recall R/2020/240 [UK]: The seat belt warning function does not meet the specification
The seat belt warning function does not meet the specification activate the correct seat belt warning scenario in the instrument cluster
Recall R/2021/082 [UK]: The communication module may be deactivated
The communication module may be deactivated carry out a check of the configuration of the communication module on affected vehicles and if necessary activate the communication module.
Recall R/2021/106 [UK]: The behaviour of the emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2021/129 [UK]: The emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2021/130 [UK]: The behaviour of the emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2021/133 [UK]: The emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2021/134 [UK]: The behaviour of the emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2017/253 [UK]: Right front seat belt pre-tensioner may not meet specification
The right front seat belt pretensioner may not conform to specification . This may adversely affect it's operation in the event of an accident. replace the pretensioner on affected vehicles.
Recall R/2018/010 [UK]: Front seat belt tensioners may not function
The front seatbelt pre-tensioner ignitors may not perform as expected. This could increase the risk of injury to the seat occupants. The lock function of the seatbelts is not impaired. on affected vehicles replace seatbelts with quality assured units.
Recall R/2020/240 [UK]: The seat belt warning function does not meet the specification
The seat belt warning function does not meet the specification activate the correct seat belt warning scenario in the instrument cluster
Recall R/2021/110 [UK]: The behaviour of the emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2021/129 [UK]: The emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2021/131 [UK]: The behaviour of the emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2021/133 [UK]: The emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall R/2021/134 [UK]: The behaviour of the emergency call system might not meet specifications
The behaviour of the emergency call system might not meet specifications. update the software of the communication module for the emergency call system.
Recall 2021514 [Canada]: Airbag
Issue: on certain vehicles, an incorrect passenger-front airbag may have been installed during a previous repair. As a result, the airbag may not inflate properly in a crash. Safety risk: an airbag that does not inflate properly can increase the risk of injury in a crash. Corrective action: mercedes-benz will notify owners by mail and instruct you to bring your vehicle to a dealer to replace the passenger-front airbag.
Recall 2018741 [Canada]: Airbag
On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: dealers will replace the passenger frontal airbag module. Note: canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected.
Recall 2018724 [Canada]: Steering
On certain vehicles originally sold or currently registered in areas of heavy road salt usage during winter months (quebec, new brunswick, nova scotia, prince edward island, and newfoundland & labrador), the bolts that attach the electric power steering assist motor to the steering gear housing may corrode and break. This could cause a loss of power steering assist. The resulting increase in steering effort could create the risk of a crash causing injury and/or damage to property. Correction: dealers will replace the mounting bolts and apply a corrosion protection coating to the gear housing and bolts. If the bolts bolt cannot be removed, a replacement steering gear will be installed.
Recall 2017490 [Canada]: Airbag
On certain vehicles, electrostatic discharge, when combined with a broken clock spring and insufficient grounding of the steering components, could lead to an inadvertent deployment of the driver's frontal airbag. Unintended airbag deployment, in a non-warranted (non-impact) situation, could startle the driver, which could result in a crash causing injury and/or property damage. In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: dealers will add sufficient grounding to the steering components. Note: a broken clock spring would result in a driver airbag warning message appearing in the instrument cluster, as well as a red airbag warning lamp illuminating.
Recall 2017207 [Canada]: Steering
On certain vehicles, the electric power steering connector may not be properly sealed against water entry. This could allow moisture to enter the power steering control unit which could interrupt the signal and cause the electric steering assist to deactivate. A loss of power steering assist could unexpectedly increase steering effort which would increase the risk of a crash causing injury and/or damage to property. Correction dealers will replace the connector and, if necessary, replace the steering rack.
Recall 2017062 [Canada]: Engine
On certain vehicles, the starting current limiter could be overloaded under certain conditions. In the event the starter is blocked, a very high electric current could flow through the starting current limiter during repeated engine starting attempts. The high electric draw could cause the starting current limiter to overheat causing the surrounding components to melt which would increase the risk of fire causing injury and/or damage to property. Correction : dealers will install an additional fuse in the electrical line to the starter.
To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.
NHTSA decoded information from VIN
139 Results returned successfully. NOTE: Any missing decoded values should be interpreted as NHTSA does not have data on the specific variable. Missing value should NOT be interpreted as an indication that a feature or technology is unavailable for a vehicle.