PIC-MF000002

SB-10051698-8488
Product Improvement Campaign
No: MF000002
Issued: 11/19/2012
Re: Engine EEC Reprogramming
Group: 13 Models: FE/FG
Expires: 11/19/2013
SUBJECT:
Customer Confidence Program MF000002 – Engine EEC Reprogramming
MODELS:
FEC52, FEC72, FEC92, FGB72
VEHICLES INVOLVED:
Certain 2012 and 2013 model year FEC52, FEC72, FEC92 and FGB72 trucks produced from April 8, 2011
through September 26, 2012.
PROGRAM:
As an important part of the Fuso Customer Confidence Program, the Engine EEC will be reprogrammed.
OWNER NOTIFICATION:
The replacement transmission aspect of the Customer Confidence Program will be released in controlled
segments to ensure a continuous availability of updated DUONIC transmission assemblies. Customers will be
notified by MFTA that a product performance enhancement is available from their local Fuso dealer. Dealers may
feel free to begin scheduling a customer appointment once the truck’s VIN appears on the dealer’s "Open
Campaigns" report beginning December 1, 2012.
MODIFICATION:
The engine EEC will be reprogrammed.
WARRANTY CLAIM SUBMITTAL FOR EEC REPROGRAMMING:
Submit a regular Warranty Service Claim A (WSC) via Fusonet for the EEC reprogramming. Enter all requested
header information, including the information listed below. MFTA Warranty will remove the MF000002 Campaign
notification from the VIN after receiving the WSC.
Warranty Service Claim Header Entry
Claim Type
Failed Labor Operation Number
A Code
B Code
C Code
Failed Part Number
W
138502
99
60
S
NPN
Warranty Service Claim Labor and Parts Entry and Failure Work Description for FE Models
Labor Operation / Work Code / Quantity / Labor Time
138502 / 99 / 1 / 1.2 hours
“Reprogram Engine EEC”
Failure Work Description
REPAIR PROCEDURE:
1. Park the vehicle on a flat, level surface, turn off the engine, apply the parking brake and chock the
wheels.
CAUTION! Do not remove the wheel chocks until all modification work has been completed.
2. Perform the Campaign using the attached modification procedure.
IMPORTANT! IF THE VEHICLE IS IN THE DEALERSHIP FOR A FAILURE AND DTC’S EXIST IN THE
SYSTEM, REMEDY THE TRUCK FIRST AND CLEAR ALL DTC’S BEFORE PROCEEDING WITH THE
EEC REPROGRAMMING.
1
Modification Procedure
Connect the Fuso Diagnostic Scanner to the Canter as shown below. Turn the ignition key switch to the ON
position. NOTE: During the reprogramming procedure, make sure the battery voltage does not drop below
11.0 VDC.
2
Open Fuso Diagnostic, open the EEC control unit and check and record the control unit’s version information.
If the software does not match the following, the EEC must be updated:
FE Models
Software – A0154484440001
Characteristics map coordinates – 0154481340001
FG Models
Software – A0154484440001
Characteristics map coordinates – 0154481440001
3
Go to MFTBC’s Field Rewrite Network (FRN) website at https://eol.mitsubishi-fuso.com/fss/ and obtain an
inquiry number and password for an EEC control module.
Insert the USB mass storage device into the laptop. Open the Adaptations tab, open the Data transfer tab,
and click on Copying from USB storage device.
Click Continue.
4
Indicates the file transfer was completed successfully.
5
1. Click
Initial startup
3. Switch off ignition.
4. Click Continue.
2. Click
Reprogramming
6
1. Switch on ignition.
2. Click Continue.
7
1. Enter inquiry number
2. Enter the password.
3. Click Continue.
8
Click Continue.
9
Click Yes.
10
Indicates the progress of the reprogramming.
11
Switch off ignition
Click Continue.
12
Indicates the progress of reprogramming.
13
1. Switch on ignition.
2. Click Continue.
14
Indicates the progress of reprogramming.
15
This screen is displayed when the programming is finished.
16
3. Click Diagnosis.
1. Click Version.
2. Check for new
information.
FE Models
Software – A0154484440001
Characteristics map coordinates – 0154481340001
FG Models
Software – A0154484440001
Characteristics map coordinates – 0154481440001
17
Turn the ignition switch OFF for a full minute. The error message below will appear. Turn the ignition switch
ON and click “Repeat” to continue.
18
Click on “Diagnosis” to return to the main diagnosis screen and click “Start quick test”.
Click Start quick test.
19
The reprogramming procedure can cause DTCs to be logged in the SSAM, IMMO, & TCM modules. If the
fault status displays a lower case letter f, those faults are stored and can be deleted using the Clear fault
memory tab. Then, turn the key to the OFF position for a full minute.
20
Turn the key to the ON position. Click Adaptations. Click Data transfer. Click Copying to USB storage
device. Safely remove the USB storage device from the laptop. Upload the File to MFTBC on the FRN
website.
21