NTB-13-057
Service Bulletin Details
Public Details for: NTB-13-057
Nissan: service information regarding certain vehicles, equipped with blind spot warning (bsw) and lane departure warning (ldw) systems, needing to be checked, diagnose, inspected and repaired, if needed, by using electronic service manual
- 2013 -
Models from 2013
2013 NISSAN ALTIMA |
SB-10052282-6119 Classification: EL13-015 Reference: Date: NTB13-057 May 23, 2013 2013 ALTIMA SEDAN; LANE DEPARTURE WARNING AND BLIND SPOT WARNING SYSTEMS SERVICE INFORMATION APPLIED VEHICLE: 2013 Altima Sedan (L33) equipped with LDW and BSW systems SERVICE INFORMATION This bulletin contains diagnostic information related to 2013 Altima Sedan vehicles equipped with the Lane Departure Warning (LDW) and Blind Spot Warning (BSW) systems. Although the Electronic Service Manual (ESM) should be used primarily when inspecting, diagnosing, and repairing LDW / BSW related issues, the supplemental information in this bulletin will assist in these areas. A sample of the items covered in this bulletin include: • What to check / inspect first when a BSW / LDW related warning is shown in the Vehicle Information Display • What to check / inspect when the BSW and / or LDW lights are flashing • If and when to diagnose stored DTCs related to BSW and / or LDW Refer to the next two pages. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/3 LDW/BSW Supplemental Diagnosis If a 2013 Altima Sedan exhibits one or more of the following items, perform preliminary checks on the next page as they apply. • Message “Malfunction – See Owner’s Manual” with LDW / BSW icons showing in the Vehicle Information Display (including but not limited to what shows in Figure 1) Vehicle Information Display Figure 1 • LDW / BSW lights to the left of the Vehicle Information Display are flashing • LDW / BSW / MOD (Moving Object Detection) related DTCs are found stored • LDW / BSW does not meet customer expectations (possibly related to environmental issues i.e. rain, etc.) 2/3 NTB13-057 Preliminary Checks Issues with other systems may trip a BSW / LDW related DTC due to improper communication. Resolve the cause of any DTCs for other systems first that are not related to the ITS (Intelligent Technology Suite) system. Once the non- BSW / LDW related DTCs are resolved, check for BSW / LDW related lights / DTCs again. Possible causes for DTC U1308: • Part(s) have been replaced: ¾ RR camera ¾ ITS controller • Disconnected / loose connections: ¾ RR camera ¾ ITS controller ¾ ITS switch • Wrong part installed (may show error 2 when calibrating): ¾ RR camera is not ITS camera ¾ Dash switch Additional notes: • IBA (Intelligent Brake Assist) light may turn on if the ITS controller is disconnected. • ITS system is sensitive to heavy rains and wet surfaces (this is stated in owner’s manual). Customer comment may state system is not working properly or note that system shuts off when no objects exist. Example: The camera unit detects reflected images of vehicles or roadside objects that are not actually in the detection zone, especially when the road is wet. Refer to the 2013 Altima Sedan Owner’s Manual, page 5-22. • LDW / BSW white icons in dash will blink on and off if the system is temporarily disabled. The “clean camera” message may also appear in the Vehicle Information Display. Normally, this is due to low washer fluid level. “Washer Fluid Low” warning will appear in the Vehicle Information Display. • If LDW / BSW white icons in dash blink and / or the “clean camera” message appears in the Vehicle Information Display and washer fluid is OK, test the washer pump related to the camera cleaning system located in the trunk. Other possible causes to check would be the pump ECU in the trunk and / or washer hoses to make sure fluid is properly getting to the camera cleaning system. • “Initialize Camera Image Calibration” in CONSULT III plus: Do not use this feature unless instructed by NNA personnel i.e. TECH LINE, etc. • When a NAVI system has been replaced, it is possible that ITS concern items may have been disconnected or triggered. Check for DTCs and if necessary, recalibrate the ITS system. 3/3 NTB13-057