FSB-216-014
Service Bulletin Details
Public Details for: FSB-216-014
Volvo: information provided regarding the coversion from twin mass flywheel to single mass flywheel. Model vn, vt. *pe
Models from 2013
2013 VOLVO VN |
2013 VOLVO VT |
Models from 2012
2012 VOLVO VN |
2012 VOLVO VT |
Models from 2011
2011 VOLVO VN |
2011 VOLVO VT |
Field Service Bulletin Trucks Volvo Trucks North America Greensboro, NC USA Date 8.2014 SB-10056545-5289 Group No. Release 216 014 01 Page 1(20) Twin Mass Flywheel Conversion Transmission Removed VN, VT FSB 216-001, Twin Mass Flywheel Conversion Transmission Removed (August 2014) This document provides the recommended procedure for converting the twin mass flywheel to a single mass flywheel. Parts Required: • Kit, Part Number 22318603 Note: Information is subject to change without notice. Illustrations are used for reference only and can differ slightly from the actual vehicle being serviced. However, key components addressed in this information are represented as accurately as possible. Service personnel: Please circulate, read and initial Service Manager Warranty Administrator PV729-FSB216-001_V Workshop Foreman Service Technicians USA64148 Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 Procedure You must read and understand the precautions and guidelines in Service Information, Function Group 4, “General Safety Practices, Transmission” before performing this procedure. If you are not properly trained and certified in this procedure, ask your supervisor for training before you perform it. DANGER Do not attempt to repair or service a vehicle without the proper training, tools and service information. Failure to do so may result in component damage, serious injury or death. 1 CAUTION To prevent distortion note the sequence of removal of all the fasteners and nuts. Position the clutch alignment tool (Tool Number 9990024). Remove the fasteners and nuts. W4088519 A – Clutch Alignment Tool Page 2(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 2 Install the pressure plate tools. W4088520 A – Fixture (Tool Number 9996857) B – Retainer (Tool Number 9996896) C – Support (Tool Number 9996996) 3 Remove the pressure plate. W4088523 Page 3(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 4 Remove the clutch disc. W4088524 5 Disconnect the engine speed sensor. W4088525 Page 4(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 6 Remove the engine speed sensor. W4088527 7 Turn the engine until the small hole in the washer plate is at the 12 o'clock position. W2088706 Page 5(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 8 Remove four bolts shown in illustration from flywheel. W2088707 9 Install four special bolts from flywheel lifting kit (tool number J-49004) in flywheel. W2088707 10 Remove all other bolts from flywheel. Page 6(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 11 Install lifting plate from flywheel lifting kit on flywheel. W2088708 12 Install jack adapter from flywheel lifting kit on transmission jack. W2088709 Page 7(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 13 Position jack adapter on flywheel lifting plate. W2088710 14 Remove four special bolts from flywheel. W2088711 Group No. Release 216 014 01 Page 8(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 15 WARNING The flywheel is heavy. Use a transmission jack and the flywheel lifting kit special tools to lift the flywheel off of the engine to avoid serious personal injury and damage to components. Remove flywheel from flywheel housing. W2088712 16 Remove two outer bolts from top of lifting plate. Position lifting eye from flywheel lifting kit on lifting plate. Install two outer bolts through lifting eye into flywheel. Note: Attach the lifting eye with the eye above the center of the flywheel. W2088713 Page 9(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 17 Position lifting chain and attach hook to lifting eye. 18 Remove the flange. W2091428 19 Clean the crankshaft flange. W4088531 20 Check the crankshaft seal for damage, corrosion or excessive wear. Replace if required. 21 Ensure that the flywheel guide pin is correctly inserted in the crankshaft. Page 10(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 22 To align the flywheel to the crankshaft, lift on the flywheel with the aid of the 2 bolts (M10x100 mm). Screw in the mounting bolts. W2091562 23 Use a drift to align the bolt holes. Install all the flywheel fasteners. Page 11(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 24 To hold the flywheel in position, install the rotation tool (Tool Number 88800014 or 88840317). W4088532 A – Rotation Tool 25 Torque the flywheel fasteners in sequence. Torque fasteners to 60 ± 5 Nm (44 ± 4 ft-lb). Torque each fastener in sequence an additional 120 ± 10 degrees. W4088533 Page 12(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 26 Remove the rotation tool. Install the plug. W4088534 27 Install the engine speed sensor. Torque fastener to 8 ± 2 Nm (6 ± 1.5 ft-lb). Note: Install a new O-ring when reinstalling the engine speed sensor W4088527 Page 13(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 28 Reconnect the engine speed sensor. W4088525 29 Install special tools (Tool Numbers 9991801 [B] and 9992564 [A]). Install the pilot bearing into the flywheel. W4088535 A – Mandrel B – Handle Page 14(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 30 Install the new clutch disc. W4088524 31 Install new pressure plate. Note: Install the clutch disc and pressure plate together. W4088520 A – Fixture (Tool Number 9996857) B – Retainer (Tool Number 9996896) C – Support (Tool Number 9996996) Page 15(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 32 CAUTION If the pressure plate fasteners are torqued out of sequence distortion damage can occur. Torque pressure plate fasteners in sequence to 53 ± 5 Nm (39 ± 4 ft-lb). W4088519 A – Clutch Alignment Tool 33 Remove the clutch release bearing hose zip ties. W4088540 Page 16(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 34 Remove the clutch release bearing hose. W4088541 35 Remove the clutch cylinder. W4088542 Page 17(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 36 Install the spacer disc. W4088543 37 Install the new clutch cylinder with the longer mounting fasteners included in the kit. Torque fasteners to 45 ± 5 Nm (33 ± 4 ft-lb). 38 Check the clutch release bearing hose O-rings for damage. Replace the O-rings (part number 22485772), if necessary. W4088544 Page 18(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 39 Install the clutch release bearing hose. Install cable ties to secure the hose into position. W4088541 40 Connect all previously removed cables to the negative (ground) battery terminals. Tighten fasteners to 20 ± 2 Nm (15 ± 1.5 ft-lb). 41 Using Premium Tech Tool run conversion kit(s) as listed below:: Note: Once the hardware conversion has been completed, run Conversion Kit 85142350 only for US07 and EM-USA10 vehicles. For EOBD-2013 and EM-USA14 vehicles, run Conversion Kit 1 and Conversion Kit 2 in order. Vehicle Conversion Kit 1 Conversion Kit 2 VN, VT, US07, ATO3112C, ATO3112D Not Applicable 85142350 VN, EM-USA10 Not Applicable 85142350 VN, EOBD-2013 85142351 85142352 VN, EM-USA14 85142351 85142352 Page 19(20) Volvo Trucks North America Field Service Bulletin Date 8.2014 Group No. Release 216 014 01 Page 20(20) Reimbursement This repair may be eligible for reimbursement if a product failure was experienced within time and mileage limits of the applicable Warranty coverage. Reimbursement is obtained via the normal claim handling process. Reimbursement UCHP Reimbursement eWarranty Claim Type (used only when uploading from the Dealer Bus. Sys.) W W Primary Labor Code 2160-03-09-01 — 1.7 hrs. 21618–2–00 — 1.7 hrs. Causal Part 21905650 21905650 Labor Code Volvo Trucks North America reserves the right to make any changes in design or to make additions to or upon its products without incurring any obligations to install the same on vehicles previously built.