01-006-14
Service Bulletin Details
Public Details for: 01-006-14
Summary to be provided on a future date.
Models from 2012
2012 MAZDA MX-5 |
Models from 2011
2011 MAZDA MX-5 |
Models from 2010
2010 MAZDA MX-5 |
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 S ... I I 9'?!"'9 ~W5iil © 2014 Mazda Motor of America , Inc. Subject: Bulletin No: 01-006/14 Last Issued: 03/12/2014 CHECK ENGINE LIGHT ON WITH OTC P2096:00 APPLICABLE MODEL(S)NINS 2010-12 MX-5 vehicles with VINs lower than JM1 NC******233876 (produced before August 5, 2013) DESCRIPTION Some vehicles may experience the Check Engine Light on with OTC P2096:00 (Target AJF feedback system too lean) . This is caused by improper control logic. To correct the problem , the control logic has been changed . Customers having this concern should have their vehicle repaired using the following repair procedure . REPAIR PROCEDURE 1. Reboot the IDS to clear memory before reprogramming . 2. Using IDS 89.03 or later software, reprogram the PCM to the latest calibration (refer to "Calibration Information" table) by following the "Module Reprogramming" procedure. NOTE: Always update the IDS tool first, then follow on-screen instructions to download the needed calibration file for PCM reprogramming . It is not necessary to remove any fuses or relays during PCM reprogramming when the IDS screen prompts you to do so. You may accidentally stop power to one of the PCM terminals and cause the PCM to be blanked, or you may receive error messages during the IDS reprogramming procedure. IDS shows the calibration part numbers after programming the PCM . Please be aware that PCM calibration part numbers and file names listed in any Service Bulletin may change due to future releases of IDS software, and additional revisions made to those calibrations for service related concerns. When reprogramming a PCM , IDS will always display the "latest" calibration P/N available for that vehicle. If any calibration has been revised/updated to contain new information for a new service concern/issue, it will also contain all previously released calibrations. When performing this procedure, we recommend using the "Power Supply" mode in the Battery Management System to keep the vehicle battery up to capacity. If a different charger is used, make sure it does not exceed 20 AMPS. If it exceeds 20 AMPS, it could damage the VCM. 3. After performing the PCM reprogramming procedure, verify the repair by starting the engine and making sure there are no MIL illumination or abnormal warning lights present. NOTE: If any DTCs should remain after performing OTC erase, diagnose the DTCs using MS3 online instructions or Workshop Manual section 01-02 . After PCM reprogramming , it is no longer necessary to road test the vehicle to "relearn" KAM (Keep Alive Memory) . Page 1of2 CONSUMER NOTICE: The information and instructions in this bulletin are intended for use by skilled technicians. Mazda technicians utilize the proper tools/ equipment and take training to correctly and safely maintain Mazda vehicles . These instructions should not be performed by "do-it-yourselfers." Customers should not assume this bulletin applies to their vehicle or that their vehicle will develop the described concern. To determine if the information applies, customers should contact their nearest authorized Mazda dealership. Mazda North American Operations reserves the right to alter the specifications and contents of this bulletin without obligation or advance notice. All rights reserved . No part of this bulletin may be reproduced in any form or by any means, electronic or mechanical---including photocopying and recording and the use of any kind of information storage and retrieval system ---without permission in writing . Bulletin No: 01-006/14 Last Issued: 03/12/2014 © 2014 Mazda Motor of America, Inc. CALIBRATION INFORM~TION Spec .., .Year ·- · CAL 2010 2011-12 FED 2010 2011-12 ) :-t:ran~mis~jon ' . . ..... Fil.e Narpe 5MT SW-LFDNEBOOO 6AT SW-LFDPECOQO 6MT SW-LFDMEBOOO 5MT SW-LFGNEEOOO 6AT SW-LFGPEFOOO 6MT SW-Lf GMEEOOO 5MT SW-LFDKEBOOO 6AT SW-LFDLECOOO 6MT SW-LFDJEBOOO 5MT SW-LFGKEEOOO 6AT SW-LFGLEFOOO 6MT SW-LFGJEEOOO .. NOTE: It is not necessary to order a PCM part for this repair procedure. WARRANTY INFORMATION NOTE: "" • ranty repair. • ' This' repair:Will • - - ' ' ~ I Thi~.yta[rar\ty information applies only to verified customer complaints .on vehicles eligible for war- be . · covered. ~nder Mazda's Federal ~mission Warra:nty {ld~g term) . Additional diagnostic time cannot be claimed for this repair. Warranty Type A Symptom Code 6X Damage Code 9W Part Number Main Cause Quantity Operation Number I Labor Hours 5555-RP-PCM 0 XXK5MXFX I 0.3 Hrs. Page 2 of2