T-SB-0023-13

@TOYOTA
T-SB-0023-13
Rev1
February 8, 2013
Technical Service Bulletin
Floor Mat Installation Du ring PDS
Service
Category
General
Section
Pre-De livery Service
Market
USA
Toyota Supports ~
ASE Certification ~
Applicability
YEAR(S)
MODEL(S)
2014
4Runner, Avalon,
Avalon HV, Camry,
Camry HV, Corolla, FJ
Cruiser, Highlander,
High lander H V, Land
Cruiser, Prius, Prius
C, Prius PHV, Prius
V, RAV4, RAV4 EV,
Sequoia, Sienna,
Tacoma, Tundra,
Venza , Yaris
ADDITIONAL INFORMATION
REVISION NOTICE
September 6, 2013 Rev1:
• Applicability has been updated to include 2014 model year RAV4 EV vehicles.
Any previous printed versions of this bulletin should be discarded.
Introduction
2014 model year vehicles are equipped with driver's side floor mat retaining clips to secure the floor
mat in the correct position_ In addition, some models may utilize retaining clips for passenger side
and rear seat floor mats as well. Follcm the appropriate installation procedure to attach the driver's
side, and if applicable , the passenger's side and rear seat floor mats to the vehicle carpet using the
floor mat retaining clips during Pre-De~very Service (PDS).
© 2013 Toyuta Motor Sales , USA
Page 1 of 9
@TOYOTA
Rev1
T-SB-0023-13
Page 2 of 9
February 8, 2013
Floor Mat Installation During PDS
Introduction (Continued)
CAUTION
• Always verify the floor mat to assure it is designed specifically for the model and model year it
is being installed in.
• ONLY use floor mats that can be retained using the retaining clips. All OEM Toyota floor mats
are specifically designed to fit correctly and be retained using the retaining clips.
• Make sure the floor mat is properly placed on the vehicle carpet and secured with the retaining
clips. If the driver side floor mat is NOT properly placed and secured, it could slip and interfere
with the movement of the pedals during driving and may cause an accident
• Verify the operation of the accelerator, brake , and clutch (if equipped) pedals and clearance
to the mat.
• NEVER install more than one floor mat at a time in the driver's seating position.
• If applicable, any secondary set of floor mats (based upon customer preference, such as the
all weather floor mats or other floor mats) MUST be placed in the trunk with all the packaging
material intact. Do NOT install the secondary mat on top of the primary floor mat already
i nstalled in the driver's seating position.
Warranty Information
OP CODE
DESCRIPTION
TIME
OFP
T1
T2
N/A
Not Applicable to Warranty
-
-
-
-
© 2013 Toyota Motor Sales , USA
®TOYOTA
Rev1
T-SB.{)023-13
Page 3 of 9
February 8, 2013
Floor Mat Installation During PDS
Installation Procedure: Hook Style
1. Verify that the driver, and if applicable , passenger side and rear seat, floor mats are for the
correct model and model year they are being installed in.
2. Attach the driver, and if applicable , passenger side and rea r seat, floor mats to the vehicle
carpet using the retaining clips. Secure the mat by inserting the retaining clips through the
grommet holes .
Figure 1.
--·'"-...·~---- ------
.
.- .
\ -.
-:: . :
,·
/)
-
.-;
·.
/
/
. . '\. .,-
;.
/
..
· ··~~---.._
- ----------------
·---~~
I
~--·-
I
G) .··
.,
.
-~
__ , ! . '· ··_.
~ ·'.: ~
.
.. ~
...... ..
·- --:::-
.
''\
' ·.'.':... ' '
,··· ~
~ - ,_ ·
/ .
-
,. ,•·: '
•
•
0
'
,'
l
~
-••. •
;;--r==n .
-;' : :·
· - -'~~ · - ·
'·
. _- · ..
,f . '\~,~ , ~·:
{·. •·'. , ~
<_,. I• . ~
' ! ~:
-· ··
' · \~ .
, I""'"";•• Cl~·
3
© 2013
To~ta
Motor Sales, USA
I
Correct Installation
.
-
@TOYOTA
Rev1
T-SB-0023-13
February 8, 2013
Page 4 of 9
Floor Mat Installation During PDS
Installation Procedure: Hook Style (Continued)
3. Verify proper installation.
NOTE
If applicable, DO NOT remove the beige "Caution" tag from the floor mat This should only be
removed by the customer.
Figure 2.
© 2013 Toyota Motor Sales, USA
@TOYOTA
Rev1
T-SB-0023-13
Page 5 of 9
February 8, 2013
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip
1. Verify that the driver, and if applicable , passenger side and rear seat, floor mats are for the
correct model and model year they are being installed in.
2. Attach the retention clip to the floor by inserting the retention clip claws into the floor eyelet.
Figure 3.
A
---------------s
@.......
1
Retention Clip
5
Cross-sectional Diagram
2
Front of Vehicle
A
Retention Clip Claw
3
Retention Clip Eyelet on Vehicle Floor
8
Locking Clip
4
Seat
© 2013 Toyota Motor Sales, USA
@TOYOTA
Rev1
T-SB-0023-13
February 8, 2013
Page 6 of 9
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip {Continued)
3. To lock the retention clip in place, insert the
Figure 4.
locking clip of the retention clip into the designated . . . . - - - - - - - - - - - - - - - - - .
hole.
1
4. Align the floor mat holes with the retention clip
hooks and place the floor mat holes onto the
retention clip hooks.
Locking Clip
Figure 5.
1
Retention Clip Eyelet on Floor Mat
2
Retention Clip
3
Front
© 2013 Toyota Motor Sales, USA
@TOYOTA
Rev1
T-SB-0023-13
February 8, 2013
Page 7of9
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip (Continued)
5. Verify proper installation.
NOTE
If applicable, DO NOT remove the beige "Caution" tag from the floor mat This should only be
removed by the customer.
Figure 6.
© 2013 Toyota Motor Sales, USA
@TOYOTA
Rev1
T-SB-0023-13
Page 8 of 9
February 8, 2013
Floor Mat Installation During PDS
Installation Procedure: Pre-installed Knob Style
1. Verify that the driver, and if applicable , passenger side and rear seat, floor mats are for the
correct model and model year they are being installed in.
2. Align the floor mat holes with the retention clip
knobs and place the floor mat holes onto the
retention clip knobs.
Figure 7.
0
3. Turn the retention clip knobs a quarter of a turn to
lock in place and verify the "triangle" marks on the
retention clip knobs and floor mat are aligned .
1
Retention Clip Eyelet on Floor Mat
2
Retention Clip
3
Front of Vehicle
Figure
a.
~-----------------.
1
Twist Knob
2
Knob in Locked Position
3
Align " Triangle" Marks
© 2013 Toyota Motor Sales , USA
@TOYOTA
Rev1
T-SB-0023-13
February 8, 2013
Floor Mat Installation During PDS
Installation Procedure: Pre-installed Knob Style (Continued)
4. Verify proper installation.
Figure 9.
NOTE
If applicable, DO NOT remove the yellow
"Caution" tag from the floor mat This should
only be removed by th.e customer.
© 2013 Toyota Motor Sales, USA
Page 9of9