S-SB-0009-14

Service Bulletin Details

Public Details for: S-SB-0009-14

Summary to be provided on a future date.


- 2014 - 2013 -

Models from 2014
2014 SCION FR-S
Models from 2013
2013 SCION FR-S
Technical Service Bulletin
S-58-0009-14
Rev1
~
'27 =:; C:: I Cl r l
April 23, 2014
Outside Door Weatherstrip - Multiple Concerns
Service
Category
Vehicle Exterior
Section
Door/Hatch
Market
USA
Scion Support s ~
ASE Cer tificatio n-
Applicability
YEAR(S)
MODEL(S)
20 13 - 20 14
FR-S
ADDITIONAL INFORMATION
REVISION NOTICE
June 16, 2014 Rev1:
• The Parts Information section has been updated.
Any previous printed versions of this bulletin should be discarded.
Introduction
Some 2013 - 2014 model year FR-S vehicles may exhibit multiple concerns from the Outer
Weatherstrip (belt molding).
The cross section of the weatherstrip has been revised to limit the amount of water passing into
the door. If the felt attached to the window stabilizers/guides accumulate water, the vehicle may
also make noise from the stabilizers/guides during window operation . In some cases , the felt on
the stabilizers/guides may freeze to the window or detach from the plastic backing and damage
the window.
Symptoms may include:
•
Noise coming from the weatherstrip during window operation , especially when wet.
•
Loosening of the weatherstrip from the door.
•
Inversion of the weatherstrip during window operation .
•
Noise from the stabilizers/guides during window operation.
• Scratches on the glass from worn stabilizers.
If the vehicle displays these symptoms, follow the procedures described in this bulletin to add ress
the condition(s) .
© 2014 Toyota Motor Sales, USA
Page 1 of 6
Rev1
S-SB-0009-14
April 23, 2014
Page 2 of 6
Outside Door Weatherstrip - Multiple Concerns
Production Change Information
This bulletin applies to vehicles produced BEFORE the Production Change Effective VIN
shown below.
MODEL
PRODUCTION CHANGE EFFECTIVE VIN
FR-S
JF1ZNAA1#E8705465
Parts Information
PART NUMBER
PART NAME
QTY
SU003-05207
Outer Weatherstrip, LH
1
SU003-05208
Outer Weatherstrip, RH
1
SU003-01616
Stabilizer, Front Door Glass, Outer (Per Door)
2
SU003-01617
Stabilizer, Front Door Glass, Inner (Per Door)
1
PREVIOUS
NEW
SU003-04334
SU003-0453 1
SU003-04771
SU003-04335
SU003-04532
SU003-04772
Warranty Information
OP CODE
DESCRIPTION
TIME
OFP
T1
T2
BD1408
Replace Front Door Panel Sub-assembly
(One Side)
1.6
Combo A
Replace Front Door Panel Sub-assembly
(Other Side)
1.6
93
13
Combo B
Replace Window Stabilizer (One Side)
0.1
SU003-04334
SU003-04335
SU003-04531
SU003-04532
SU003-04771
SU003-04772
Combo C
Replace Window Stabilizer (Other Side)
0.1
APPLICABLE WARRANTY
• This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months
or 36,000 miles, whichever occurs first, from the vehicle's in-service date.
• Warranty application is limited to occurrence of the specified condition described in
this bulletin.
© 2014 Toyota Motor Sales, USA
S-SB-0009-14
Rev1
April 23, 2014
Page 3 of 6
Outside Door Weatherstrip - Multiple Concerns
Required Tools & Equipment
SPECIAL SERVICE TOOLS (SST)
PART NUMBER
QTY
Plastic Pry Tool Kit*
00002-06020-01
1
Tool, Front Door Glass Adj *
09812-18010-01
1
REQUIRED MATERIAL
QUANTITY
Toyota Genuine Adhesive 1344, Three Bond 1344, Loctite® 242 ,
or Equivalent (for window nuts)
As Needed
* Essentia l SST.
NOTE
Additional SSTs may be ordered by calling 1-800-933-8335.
Overview Procedure
1. Confirm the condition .
2. Disassemble door per the Repair Manual.
3. Reassemble door and adjust window glass.
4. Reinitialize window.
Inspection Procedure
NOTICE
BEFORE performing the procedures in this bulletin, ensure there is NO body or door damage that
may affect the alignment of the side window glass.
Removal Procedure
NOTE
Use the same procedure for both the RH and LH sides.
Refer to the Technical Information System (TIS), applicable model and model year Repair Manual:
• 2013 I 2014 FR-S:
Vehicle Exterior - Exterior Panels I Trim - "Front Door Belt Moulding: Removal"
1. Disconnect cable from the negative(-) battery terminal.
2. Remove front door trim board sub-assembly with power window switch assembly.
3. Remove front door trim board sub-assembly.
© 2014 Toyota Motor Sales, USA
S-SB-0009-14
Rev1
April 23, 2014
Page 4 of 6
Outside Door Weatherstrip - Multiple Concerns
Removal Procedure (Continued)
4. Remove front door service hole cover.
5. Remove front door glass sub-assembly.
Refer to TIS , applicable model and model year Repair Manual.
• 2013 I 2014 FR-S :
Vehicle Exterior- Front Door- "Door I Hatch : Front Door: Disassembly"
HINT
Note position of the inner stabilizer bolt as a reference for window alignment before removing
the Front Door Glass sub-assembly.
6. Remove front door glass Outer Weatherstrip
assembly.
Figure 1.
A. Remove the screw.
B. If necessary, use a screwdriver to disengage
the claw and remove the front door glass
Outer Weatherstrip assembly.
NOTICE
Tape the screwdriver tip before use.
7. Inspect Door Glass Inner and Outer Stabilizers for wear or damage.
NOTE
Replace stabilizers if felt guide surface is worn or damaged.
Installation Procedure
NOTE
Use the same procedure for both the RH and LH sides.
1. Install Inner and Outer Window Stabilizers if necessary.
HINT
Leave Inner Window Stabilizer bolt loose until window is installed.
© 2014 Toyota Motor Sales, USA
S-SB-0009-14
Rev1
April 23, 2014
Outside Door Weatherstrip - Multiple Concerns
Installation Procedure (Continued)
2. Install front door glass Outer Weatherstrip
assembly.
Figure 2.
Engage the claws to install the screw and a NEW
front door glass Outer Weatherstrip assembly
as shown.
NOTE
Ensure proper installation of Outer
Weatherstrip by confirming that the claw
attached to the weatherstrip is fully engaged.
3. Install front door glass sub-assembly.
Refer to TIS , applicable model and model year Repair Manual:
• 2013 I 2014 FR-S :
Vehicle Exterior - Door/Hatch - "Front Door: Reassembly"
NOTE
Use Loctite™ 242 or equivalent on front door glass flange nuts.
4 . Adjust front door glass sub-assembly.
Refer to TIS , applicable model and model year Repair Manual:
• 2013 I 2014 FR-S :
Vehicle Exterior - Door/Hatch - "Front Door: Adjustment"
HINT
Align Inner Stabilizer bolt to original position as a reference for window alignment.
5. Install front door service hole cover.
6. Install power window switch assembly with front door armrest base panel.
7. Install front door trim board sub-assembly.
© 2014 Toyota Motor Sales, USA
Page 5 of 6
' ' " SC:ICJn
'27
S-SB-0009-14
Rev1
Apri l 23, 2014
Outside Door Weatherstrip - Multiple Concerns
Installation Procedure (Continued)
8. Install door armrest cover.
9. Connect cable to negative (-) battery terminal.
Torque: 6.0 N*m (61 kgf*cm, 53 in*lbf)
10. Initialize power window control system .
11 . Confirm the repair.
© 2014 Toyota Motor Sales, USA
Page 6 of 6


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.