13-BE-002
Service Bulletin Details
Public Details for: 13-BE-002
Summary to be provided on a future date.
Models from 2012
2012 HYUNDAI GENESIS |
Models from 2011
2011 HYUNDAI GENESIS |
Models from 2010
2010 HYUNDAI GENESIS |
Models from 2009
2009 HYUNDAI GENESIS |
GROUP HVUnDRI nEW THlnKlnG. Technical Service Bulletin SUBJECT: BODY ELECTRICAL nEW POSSIBILITIES. DATE NUMBER 13-BE-002 MODEL(S) FEBRUARY 2013 GENESIS SEDAN (BH) STEERING COLUMN POWER TILT AND TELESCOPE MODULE REPLACEMENT This bulletin supersedes TSB 11-BE-003 to update the service procedure and part numbers. Description: This bulletin provides seNice procedures to replace the tilt and telescope module for some BH Genesis vehicles. Applicable Vehicles: •Model: Genesis Sedans (BH) with power tilUtelescope column •Production Range: From April 25 1h, 2008 to May 3rd, 2011. *NOTE For vehicles produced from April 25, 2008 through November 14, 2009, an additional procedure is required (Service Procedure #2). Service Procedure #2 is not applicable to vehicles produced after November 14, 2009. All vehicles must have Service Procedure #3 performed after replacing the tilt/tele unit (Service Procedure #1 ). Parts Information: PART NAME Part Number QTY 95450-3M 151 1 Circulate To: General Manager, SeNice Manager, Parts Manager, Warranty Manager, SeNice Advisors, Technicians, Body Shop Manager, Fleet Repair ~ SUBJECT: STEERING COLUMN POWER TILT AND TELESCOPE MODULE REPLACEMENT Warranty Information: OP CODE OPERATION OP TIME 95401ROO Steering column tilt & telescope unit replacement 0 .5 M/H SERVICE PROCEDURE: Perform the following procedures in order. SERVICE PROCEDURE #1 . STEERING COLUMN TILT & TELESCOPE UNIT REPLACEMENT *NOTE - Before beginning, note all radio presets. Presets should be reset at the conclusion of this service procedure. - Disconnect battery negative terminal before performing this service procedure. 1. Partially remove the left door weatherstrip (A). 2. Remove the crash pad side cover (B). TSB #: 13-BE-002 Page 2 of 7 ' SUBJECT: STEERING COLUMN POWER TILT AND TELESCOPE MODULE REPLACEMENT I 3. Loosen the lower panel mounting screws (C) . 4. Disconnect the lower panel connectors (D) and then remove the lower panel. 5. Remove the reinforcement panel by loosening the mounting nuts (E). TSB # : 13-BE-002 Page 3 of 7 ' SUBJECT: 6. STEERING COLUMN POWER TILT AND TELESCOPE MODULE REPLACEMENT Disconnect the steering column tilt & telescope unit connector (F) and remove the mounting nut (G). Remove the steering column tilt & telescope unit (H). 7. Remove the steering column tilt & telescope unit ECU by releasing the lock from the mounting bracket (I). Install a new steering column tilt & telescope unit in reverse order of removal. TSB #: 13-BE-002 Page 4 of 7 . SUBJECT: STEERING COLUMN POWER TILT AND TELESCOPE MODULE REPLACEMENT SERVICE PROCEDURE #2. STEERING COLUMN TILT AND TELESCOPE SWITCH REMOVAL *NOTE This procedure is only applicable to vehicles produced from April 25, 2008 through November 14, 2009. If vehicle is produced after November 14, 2009, skip to Service Procedure #3. Vehicles built before November 15, 2009 have tilt and telescope travel limit switches. The new tilt & telescope unit does not use these inputs and it is required to remove them according to the procedure below. 1. Remove the steering column lower shroud (B) by loosening the mounting screws (A). 2. Cut the tilt switch wiring from the switch end part (C) to the band cable (D) as shown in the photo . TSB #: 13-BE-002 Page 5 of 7 .. SUBJECT: 3. STEERING COLUMN POWER TILT AND TELESCOPE MODULE REPLACEMENT Cut the telescope switch wiring from the switch end part (E) to the end part (F) of the motor connector as shown in the photo. *NOTE Cut the wiring as close as possible to the band cable or switch. 4. Reinstall all the removed parts in reverse order of removal. TSB #: 13-BE-002 Page 6 of 7 c .. SUBJECT: STEERING COLUMN POWER TILT AND TELESCOPE MODULE REPLACEMENT SERVICE PROCEDURE #3. STEERING COLUMN TILT & TELESCOPE UNIT ADJUSTMENT Make sure to follow the procedures below in order. Push the steering column tilt & telescope switch to the CD direction and hold it about for 1 second . 2. Push the steering column tilt & telescope switch to the Cg) direction and hold it about for 1 second. 3. Push the steering column tilt & telescope switch to the @ direction and hold it about for 1 second . 4. Push the steering column tilt & telescope switch to the @ direction and hold it about for 1 second. 5. Procedure is complete . TSB #: 13-BE-002 Page 7 of 7