TSB-0102-14

@TOYOTA SEQUOIA
2015 PRE-DELIVERY SERVICE CHECK SHEET
.
~I .:.!
~
BEFORE INSPECTION
0
01 Install Short Pin (see page 2) ........................................
0
UNDER VEH ICLE (ON HOIST)
~CZ:
01 Remove disc b rake anti -rust covers/anti-corros ion
wheel film ................................................................ ...... .
02 Inspect tires for defects/damage ................................. .
03 Initialize lire Pressure Warning System (TPWS)
(see page 2) ........... ....................... .... ........................
... .
04 Install wheel covers/caps/spare tire wheel covers-. .. .
05 Inspect for fuel, oil, coolant. and other fluid leaks . . . ...
06 Inspect under the vehicle for damage, rust, etc ... .. . ..
07 Visually check bolts and nuts on c hassis and powertrain
for looseness .. .. . .. . . .. .... ... . . .. .. .. . . . . . .. . .. . ... . .. .. . . . .. . . . . . . ...
08 Install rubber body plugs (stored in glove box or center
console)" ............ ..... ........... .. ... . .. . .... ....
. ..
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition •tG-ON"; place gear selector m reverse. tum
on lights and rear defogger Unlock doors release fuel door
01
02
03
04
05
06
07
08
09
10
11
Check dome, courtesy, map , and sun visor lights• .......
Check warning/indicator lights, gauges, and horn .........
Check windshield wipers and washers ...........................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ............. ..............
Check inside/outside rear view mirror operation/
adjustment. ............................................ . . . .. . .. . . ... . ... ..
Check cigarette lighter and power outlets• ......... .............
Check audio/navigation*/backup camera• system and
set clock......................... .. ....................................
Install shift-lock override button cover ............................
Check sliding roof* ......... ............ ......................................
Check Rea r Seat Entertainment system operation* ........
Check Parking Assist system* .... ....... ..............................
DO
DO
OD
DO
DO
DO
DO
0
Enter Odometer Reading
00
00
00
Reading Before Test _ _ __ _ Reading After Test - -- - - -
01
02
03
04
05
06
07
08
09
10
11
12
13
14
DO
DO
00
00
DD
OD
DD
DD
DD
OD
DD
.
Check cold engine operation ......... ...... ....................... ....
Check engine operation during warm-up ... ......................
Check engine at normal operating temperature . ......... .. ..
Check automatic transmission operation ............ . ......... ..
Check brake and parking brake operation ...... ..... ...........
Check steering operation and off-center/vehicle
pull/flutter ........ ............. ... ........ .........................................
Inspect for abnormal noise and vib ration .. ..... . . .... .. ....
Inspect for squeaks and rattles ........................................
Check front and rear* heater and A/C operation..............
Check cruise control operation .. .. . . .. . . . .. . .... . . .. . . .. . . . ... .. . .
Check Blind Spot Monitor system· .... ...... ... .. ... .. ....
Check front seat heater/ventilation operation• ........... ......
SeUcalibrate compass• (see page 2)... ........... .................
Check rear height control air suspension*. .. ....................
D D
DD
0 D
DD
0 0
0 D
DD
0 D
0 0
DD
D 0
D 0
CJ 0
CJ 0
FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc (Remove just before delivery to customer).......
02 Visually inspect all interior pa rts for installation,
damage, fit, dirt, etc............................ .. .. .. . . ... . .. . . .. . . ... ..
03 Verify floor mat application and install us i ng
retain ing clips* ..................... ..................... .....................
04 Remove Rapgard™ and clear protective bumper film' ....
05 Wash and clean vehicle ................................................
06 Inspect pai nt fin ish for scratches, c hips, rust, dents,
damage, etc...................................... .. ... .. .... .. ......... .........
07 Inspect exterior body parts for proper installation,
damage, rust, etc.............................................................
08 Place oil cha nge sticker on inside of windshield, top
left corner .. .. . .. .. . .. . . . .. . ... .. ... .. .... . . .. . . ... . .. .. . . .. . . .. . . . .. . . . .. .. . . ..
09 Place Owner's Guide and first aid kit portfol io* in
glove box ... .. .......... ....... ................................................. .
10 Perform Techstream Health Check .... ........................... .
11 Install front license plate and mounting bracket*
(see page 2) . . .. .. . .. ... .. . . .. .. . . . .. ... .. . .. . . .. . . .. .. . . . .. . .. .. . .. . . . . .. .. . . .
UNDER HOOD
Check engine oil level ............. ....................... .. .......
Check brake and power steering* fluid levels .................
Check engine coolant level. ............... ...... ..... ..................
Check windshield washer fluid level . ...........................
05 Chec k battery s tat e-of-ch arge using Digital Battery
System A nalyzer (SOC Reading:
%) .....
06 Inspect for fuel , oil, coolant, and other fluid leaks .... ........
D
ROAD TEST
Start al left front door Check window and door lock operation (from master power
switch. if equipped) Continue around vehicle in a counterclockwise d1rect1on
checking each door and window operation. child door locks. seal bells, interior
condition, all lights, luggage compartment contents Finish by checking headlight
aim and continue into UNDER HOOD checks.
01
02
03
04
0
OD
OD
D
DD
DO
DD
A complete road test helps assure customer sa/1sfact1on Dnve vehicle over a
variety of road surfaces and dnvmg cond1t1ons Check for unusual noise and
driving performance
WALKAROUND INSPECTION
01 Check Smart Key System* ........................ .. ... .. ... ...
02 Check door and door lock operation, including each
w ireless remote control/theft deterrent system* ...............
03 Check window ope ration .................................................
04 Check that engine starts with all keys ..............................
05 Check that child safety door locks are in normal
(unlocked) position* .........................................................
06 Check seats and seat belt operation .............................
07 Check rear defogger*/rear view mirror defogger' ............
08 Check side marker, tail, backup, and license plate lights.
09 Check luggage compartment light* and trim appearance
1O Check jack and tool installation ······································
11 Check headlight aim ........................................................
August 201•
DO
DD
OD
DD
DD
OD
Inspect or install when equipped/required .
D
0 D
0 0
D
D
D 0
D 0
D
D
DD
0
Completion and retention of this form is required to comply with Toyota's Warranty Polley
TECHNICIAN'S SIGNATURE
I
NAME (PLEASE PRINT)
Date
Dealer Name
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
SERVICE MANAGER'S SIGNATURE
I
NAME (PLEASE PRINT)
Dealer Code
I
Vehicle Identification Number (Sticker)
SHORT PIN INSTALLATION
To minimize battery discharge the Short Pin has been removed
and is stored in the engine compartment Relay Block.
Install the Short Pin.
NOTE
If the vehicle is stored in the dealership for a long period of
time after PDS, disconnect the negative(-) battery terminal
to prevent battery discharge. Refer to Service Bulletin No.
PG001-06, "Battery Maintenance for In-Stock Vehicles &
Pre-Delivery," for battery maintenance information.
1 Storage Location
2 Installation Location
TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPWS sensor.
NOTE
To adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature,
perform a Health Check using Techstream and select the "Compensation Tire Pressure" checkbox. The compensation
pressures will be displayed on the Health Check results screen . Adjust the tire pressure when the tires are cold .
COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rear view mirror.
NOTE
• Do NOT perform calibration of the compass in a place where the Earth 's magnetic field is subject to interference
(underground parking , under a steel tower, between buildings, roof parking, near a railroad crossing , near a large
vehicle, etc.).
• During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with
the calibration .
FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION*
The bracket and 6 mounting screws are placed in a vinyl bag located on the right front passenger's side floor.
Installation Procedure
Attach the license plate bracket by snapping the clips on th e
top of the bracket onto the lower lip of the air intake opening
on the bumper.
2. Align the 4 mounting holes in the bracket with the 4 dimples in
the bumper.
3. Screw two 20 mm (0.787 in.) self-tapping mounting screws (A)
into the top holes on the bumper and then screw the two 30 mm
(1 .81 in .) self tapping screws (B) into the bottom holes.
4. Align the mou nting holes in the license plate with the
corresponding holes in the bracket. Using the 2 remain ing
20 mm (0. 787 in .) self-tapping screws (A) , mount the license
plate directly to the bracket assembly.
1.
NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT overtighten the self-tapping screws.
1 License Plate
2 Screw A: 20 mm (0.787 in .)
3 Screw B : 30 mm (1.81 in .)
4 Front License Plate
Mount ing Bracket