T-SB-0091-12
Service Bulletin Details
Public Details for: T-SB-0091-12
Summary to be provided on a future date.
- 2012 - 2011 - 2010 - 2009 - 2008 -
Models from 2012
2012 TOYOTA HIGHLANDER |
2012 TOYOTA HIGHLANDER HYBRID |
Models from 2011
2011 TOYOTA HIGHLANDER |
2011 TOYOTA HIGHLANDER HYBRID |
Models from 2010
2010 TOYOTA HIGHLANDER |
2010 TOYOTA HIGHLANDER HYBRID |
Models from 2009
2009 TOYOTA HIGHLANDER |
2009 TOYOTA HIGHLANDER HYBRID |
Models from 2008
2008 TOYOTA HIGHLANDER |
2008 TOYOTA HIGHLANDER HYBRID |
®TOYOTA T-SB-0091-12 Rev2 Technical Service Bulletin June 21, 2012 Power Back Door Does Not Close Properly Service Category Vehicle Exterior Section Door/Hatch Market USA Toyota Supports ~ ASE Certification. . Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2008 - 2012 Highlander, Highlander WMl(s): 5TD, JTE HV REVISION NOTICE July 18, 2013 Rev2: • Production Change Information section has been updated. October 22, 2012 Rev1: • Production Change Information, Warranty Information, and Parts Information sections have been updated. Any previous printed versions of this bulletin should be discarded. Introduction Some 2008 - 2012 model year Highlander and Highlander HV vehicles may exhibit a condition where the Power Back Door does not close properly. The Back Door may get to the fully closed position and then reverse to the open position. In cases where the Power Back Door does close, a pop or clunk noise may also be heard when the back door latch reaches the striker during the power close function. In some cases, Diagnostic Trouble Codes (DTCs) B2222 and/or U0230 may be present. Use the following information to inspect the Power Back Door and address this condition . NOTICE The purpose of this Service Bulletin is to provide repair instructions for the Power Back Door. It enhances the durability of the Power Back Door when operating using the Power Close function. When the Power Close function is used, if objects or cargo are continually interfering with the closure of the back door, damage to the back door and/or back door hinges may occur. To minimize the possibility of damage occurring, before closing the Power Back Door, customers should always confirm that objects in the cargo area will not impede or interfere with the closing operation of the back door. Additionally, customers should not use any part of their body to intentionally activate the Jam Protection function of the Power Back Door. Please see the Owner's Manual for additional information on the Power Back Door Jam Protection function. © 2013 Toyota Motor Sales, USA Page 1 of 8 @ TOYOTA T-SB-0091-12 Rev2 June 21, 2012 Page 2 of 8 Power Back Door Does Not Close Properly Production Change Information This bulletin applies to vehicles produced BEFORE the Production Change Effective VINs shown below. DRIVE TYPE GRADE PRODUCTION CHANGE EFFECTIVE VIN 2WD All 5TD#K3EH#CS088602 4WD All 5TD#K3EH#CS 173141 4 Cyl 2WD All 5TDZA3EH#CS030853 4WD Base JTEDC3EH#C2010777 HV Limited JTEDC3EH#C2010780 ENGINE 6 Cyl Warranty Information DESCRIPTION OP CODE 801122 Inspection of Rear Hinges, Hatch Assembly, & Door Motor Only* TIME OFP T1 T2 0.5 68810-48040 68810-48041 68810-48090 68810-0E070 68810-0E071 9A 13 * Use typical body shop sublet type "ZZ" other to claim practice for claiming preparation, repair, sealing , and painting of the rear hinges and back door panel assembly. APPLICABLE WARRANTY • This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. • Warranty application is limited to occurrence of the specified condition described in this bulletin. © 2013 Toyota Motor Sales, USA @TOYOTA Rev2 T-SB-0091-12 June 21, 2012 Page 3 of 8 Power Back Door Does Not Close Properly Parts Information NOTE Please review entire Inspection Procedure BEFORE ordering parts, all parts shown below may NOT be necessary to correct this condition. PART NUMBER PART NAME QTY 68810-0E120 Hinge Assy, Back Door, RH (Pad Thickness = 2 mm) 1 68820-48030 68820-48031 68820-0E060 68820-0E061 68820-0E090 Hinge Assy, Back Door, LH (Pad Thickness = 2 mm) 1 67005-48430 67005-48431 67005-0E230 67005-0E231 67005-0E232 Panel Sub-Assy, Back Door (PBD) 1 85007-09001 85007-09002 Motor Unit, Back Door (Includes Upper Rod and Stud) 1 69356-48010 Back Door Upper Rod (Includes Lift Arm Stud) 1 68961-23010 Lift Arm Stud 1 90080-11194* Bolt, w/Washer* 4 PREVIOUS NEW 68810-48040 68810-48041 68810-0E070 68810-0E071 * Non-reusable part. Required Tools & Equipment REQUIRED EQUIPMENT SUPPLIER Techstream 2.0** TIS Techstream PART NUMBER QTY TS2UNIT ADE Techstream Lite ** Essential SST. © 2013 Toyota Motor Sales, USA TSPKG1 TSLITEDLR01 1 @TOYOTA T-SB-0091-12 Rev2 June 21, 2012 Page 4 of 8 Power Back Door Does Not Close Properly Required Tools & Equipment (Continued) NOTE • Only ONE of the Techstream units listed above is required. • Software version 8.10.021 or later is required. • Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787. REQUIRED MATERIAL QUANTITY Feeler Gauge As Needed Inspection Procedure Inspect the Power Back Door Assembly. 1. Inspect the upper hinges for any gaps present by placing a 0.05 mm (0.002 in.) or greater feeler gauge between the 2 bolts mounted to the back door as shown in Figure 1. If a gap exists, replacement of both Back Door Hinges AND the Back Door Panel Sub-assembly is required . Proceed to step 2. If a gap is not found , STOP - this bulletin does NOT apply. Figure 1. 1 I Gap Location © 2013 Toyota Motor Sales, USA @TOYOTA T-SB-0091-12 Rev2 June 21, 2012 Page 5 of 8 Power Back Door Does Not Close Properly Inspection Procedure (Continued) 2. Visually inspect the back door motor teeth for damage by opening the back door and manually moving the door towards the half-closed position while observing the large gear teeth for damage, as shown in Figure 2. If damage is found, replacement of the Back Door Motor Unit is required. Figure 2. 3. Visually inspect the Back Door Upper Rod and Lift Arm Stud for bends or damage. If it is bent, or damage is found, replacement is required. Figure 3. NOTE The Back Door Upper Rod and Lift Arm Stud are available as separate service parts from the Back Door Motor Unit if found damaged or bent. 1 Lift Arm Stud 2 Back Door Upper Rod 4. Proceed to Repair Procedure. © 2013 Toyota Motor Sales, USA I @TovoTt Power T-SB-0091-12 Bae~ Rev2 June 21, 2012 Page 6 of 8 Door Does Not Close Properly Repair Procedle I 1. )Sublet vehicle repair of the back door and back door hinges refinishing to a body shop if necessary. Repainting and repair of the back door and hinges should be done in accordance \with Toyota's body repair recommendations. IRemove and replace the back door, hinges, and lift arm/Power Back Door motor as needed based off inspection procedures in this bulletin. NOTE Original centering bolts used for the hinge assemblies are NOT reusable. Substitute referenced hardware in the Parts Information table (P/N 90080-11194). Refer to the Technical Information System (TIS), applicable model and model year Repair Manual and the following manuals: • Toyota Fundamental Body Repair Procedures Manual (Pub. No. BRM002E), available from the Materials Distribution Center (MDC) through Dealer Daily - Dealer Support Materials O~ra . • Toyota Collision Repair Manuals: • Toyota 2008-2013 Highlander Collision Repair Manual (BM06JOU) • Toyota 2008-2013 Highlander HV Collision Repair Manual (BM07VOU) © 2013 Toyota Motor Sales, USA - -- I ·~· @TOYOTA T-SB-0091-12 Rev2 June 21, 2012 Page 7 of 8 Power Back Door Does Not Close Properly Repair Procedure (Continued) NOTE To ensure correct installation of the back door struts, note the markings on the assembly (Figure 4). The markings indicate on which side of the car the strut should be installed, and the direction of the braces on the strut. Figure 4. © 2013 Toyota Motor Sales, USA @TOYOTI Power T-SB--0091-12 Rev2 June 21, 2012 Page 8 of 8 Baer Door Does Not Close Properly Repair Procedure (Continued) ! 2.1 Initialize the Power Back Door system. I i Refer to TIS, applicable model and model year Repair Manual: I, • 2008 I 2009 I 2010 I 2011 I 2012 Highlander: Vehicle Exterior - Door/Hatch - "Engine Hood I Door: Power Back Door System: Initialization" • 2008 I 2009 I 2010 I 2011 I 2012 Highlander HV: Vehicle Exterior - Door/Hatch - "Engine Hood I Door: Power Back Door System: Initialization" 3. \Confirm repair by opening and closing the back door in the power mode and ensuring proper operation. · f © 2013 Toyota Motor Sales, USA -- 1-