T-SB-0163-13

®TOYOTA
T-58-0163-13
November 6, 2013
Technical Service Bulletin
Entune/Navigation Software Update Process for Display
Audio (Non-HOD Type)
Service
Category
AudioNisual/Telematics
Section
Navigation/Multi Info Display
Market
USA
Toyota Supports ~
ASE Certification-
Applicability
YEAR(S)
MODEL(S)
2012-2013
4Runner, Corolla,
RAV4, Tacoma
2013-2014
Avalon, Avalon HV,
Venza
2012 - 2014
Camry, Camry HV,
Prius, Prius C, Prius
PHV, Prius V
2013
Highlander, Highlander
HV
ADDITIONAL INFORMATION
SUPERSESSION NOTICE
The information contained in this bulletin supersedes SB No. T-SB-0026-12.
• Applicability has been updated to include 2014 model year vehicles.
• The software version number, the SST part number, and the Repair Procedure have been
updated.
Service Bulletin No. T-SB-0026-12 is Obsolete and any printed versions should be discarded. Be
sure to review the entire content of this bulletin before proceeding.
© 2013 Toyota Motor Sales, USA
Page 1 of 5
@TOYOTA
Page 2 of 5
November 6, 2013
T-SB-0163-13
Entune/Navigation Software Update Process for Display Audio (Non-HOD Type)
Introduction
Use the following procedures to check and/or update the softwa re version of Entune/Navigation for
Non-HOD Type units.
NOTE
• Non-HOD Type Navigation units have a CD slot visible on the front of the radio.
• HOD Type Navigation units have a tilt-open navigation screen and CD slot beh ind the screen .
Required Tools & Equipment
PA RT NUMBER
QTY
0101 O-HBEKR-1 38
1
SPECIAL SERVICE TOOLS (SST)
USB Drive Firmware Update - Harman Becker*
* Essential SST.
NOTE
Additional SSTs may be ordered by calling 1-800-933-8335.
Warranty Information
OP CODE
DESC RIPTION
TIME
OFP
T1
T2
N/A
Not Applicable to Warranty
-
-
-
-
© 2013 Toyota Motor Sales, USA
@TOYOTA
T-SB-0163-13
November 6, 2013
Page 3 of 5
Entune/Navigation Software Update Process for Display Audio (Non-HOD Type)
Software Version Check Procedure
1. Press the Setup button.
2. In the Setup menu, select General.
Figure 1.
3. In the General Settings menu, scroll down and
select System Information.
Figure 2.
4. In the System Information menu the Software
Version information is displayed (eg ., 1.7.x, 1.8.4,
2.1.0, 2.2.0).
n:l!tl!"11f:•••
Figure 3.
© 2013 Toyota Motor Sales, USA
,
@TOYOTA
T-SB-0163-13
Page 4 of 5
November 6, 2013
Entune/Navigation Software Update Process for Display Audio (Non-HOD Type)
Software Update Procedure
1. Start the vehicle or put hybrid system in Ready ON mode.
2. Turn on the radio.
3. Press the Apps button (the system will switch to the Apps main page).
4. Install USB Drive SST into vehicle's USB slot (there will be a short pause while the software
version is read) .
5. An "Update software from X.X.X to 3.1.0?"
message will be displayed.
Figu re 4 .
6. Select Yes.
7. A "Please do not interrupt the software update
once it has started. The engine must be
running during software update." message will
be displayed.
Figure 5.
Please do not interrupt the software update
once it has started. The engine must be
running during software update.
Confirm
8. Select Confirm (the engine must be running or hybrid system in Ready ON mode during
software update).
9. The Software update will begin and the screen
will show a "Package 1 of 8" message, and
continue through 8 of 8. It will take approximately
5 minutes for the update to complete.
Figu res.
© 2013 Toyota Motor Sales, USA
@TOYOTA
Page 5 of 5
November 6, 2013
T-SB-0163-13
Entune/Navigation Software Update Process for Display Audio (Non-HOD Type)
Software Update Procedure (Continued)
10. When finished , a "Software update complete"
message is displayed.
Figure 7.
11 . Remove the USB Drive SST.
12. Turn the vehicle off then restart it.
13. Confirm the software version was updated
by performing the Software Version
Check Procedure.
Figure 8.
System Information
Device ID I Product ID:
B11z0 ,1wEXJ
i9 !. .! . . . w
7708
Software Version: 3.1.0
Navl0: 20110502
© 201 3 Toyota Motor Sales, USA
~ Co~y
to USB